70mai Dash Cam Pro.

70mai Dash Cam Pro. It is a car dvr offering many functions to enhance driving safety.

Key Features: Parking monitoring Advanced driver assistance system Superior day and night vision APP support, easy to play and download Compact design 3-minute installation voice control

WDR: Adjust the exposure balance so the camera can get more detailed information, allowing the dashboard to process more light on the Sentor and create a brighter image.

Defog ALGorithm: (Defog Algorithm) effectively reduces distortion or degradation of images and reproduces clear vision while driving in smoke and haze conditions.

G-Sensor: 70mai Dash Pro automatically starts recording when a collision is detected. Frames locked in the event file are separated from the regular file.

140 ° Wide Angle: Allows you to record a wider angle of view and allow DRIVERS to see 4 lanes. Along with 6 glasses, it can provide light transmission, thus record crystal clear video signal.

2592 x 1944 Pixels HD: 2.5 times 1080P HD resolution, produce road movies anytime, anywhere, capture the details of your routes, never miss any wonder when traveling.

6-Glass Lens: 6-layer glass lenses allow 70mai Dash Cam Pro to prevent blur in multiple climates and conditions along with the Defog effect.

APP Enabled: connected to the device’s hotspot, you can easily access the Internet, view and download video images while traveling without using mobile traffic.

SONY IMX335, F / 1.8: SONY IMX335. It is a type of image sensor widely used in cameras for its ability to capture crisp, high resolution images and footage even in low light conditions.

Instructions

Product overview

Installation Please install the product following the below method.

Install the electrostatic sticker Remove the electrostatic sticker from the shipping box and place it in the recommended area on the windshield as shown in the figure below. Please clean the windshield and remove any air bubbles between the electrostatic sticker and the windshield during installation.

Connect 70mai Dash Cam Pro to the bracket Attach the bracket to the 70mai Dash Cam Pro as shown in the picture below. You will hear a click when it is in place.

Attach Dash Cam Pro Remove the protective sticker on the bracket of the 70mai Dash Cam Pro and attach the dash cam to the center of the electrostatic sticker as shown in the picture below. Press the bracket by hand to make sure the heat-resistant adhesive is in close contact with the electrostatic sticker.

Connect the power source As shown in the illustration, run the power cable along the top of the windshield, the C-pillar, and around the passenger glove box. Position the end so that it goes to the cigarette lighter port. After connecting to car charger, plug the charger into the port

Adjust the angle of the Dash Cam Pro Turn on the Dash Cam Pro and adjust the angle of the camera up and down against the preview screen to make sure the camera is facing the front.

70mai Smart Dash Cam Pro Activation

70mai Smart Dash Cam Pro needs to be activated with 70mai app. Visit the website below to download and install the 70mai app.

Select “Add device” in 70mai app and complete activation as requested.

Specifications Image sensor: SONY IMX335 Resolution: 2592 × 1944 Camera FOV 140 °, F1.8, 6 pieces Wireless connection: Wi-Fi IEEE 802.11 b / g / n / 2.4ghz G-sensor: acceleration sensor Expandable memory: 16-64 GB microSD card and read / write speed Class10 and above Supported OS: Android4.4 / iOS8.0 and above Power supply: car cigarette lighter Battery type: lithium polymer battery Battery capacity: 500mA Input: 5V 2A Operating temperature:.10 ° C

70mai Dash Cam.

Xiaomi 70mai Dash Cam Smart WI-FI Smart Dash Cam Car DVR with Built-in WI-FI. International version

Smart, simple and secure

Provide reliable information about the accident. Help with insured events. Shot of a roadside landscape.

70mai Dash Cam Accurate Voice Control Automatic Emergency Recording Night Vision App Control Video Playback Easy Installation

Voice control. Hands-free teams, driving with safety

Application control. Built-in WI-FI, free traffic

Mini design. Obstacle free, full view

Installation in 3 minutes. The easiest way to install

Wide FOV 130 ° Built-in AI Adjustable Lens Angle 1080 Full HD High Sensitivity Sensor Clear Night Vision

Power button

The device only has one button, the power button.

When the device is turned off Press to turn on the device;

When the device is on Press to On. / Off. WI-FI access point; Press and hold to turn off the device; Press 3 times to format the TF card; Press 5 times to restore default settings.

Indicator

A ring indicator is located on the outer edge of the power key. The indicator has the following states:

Off state When the device is off, the indicator is also off.

Saving state When the device is turned on, the indicator turns on. While the device is in another mode, the color of the indicator differs as follows:

Green: usually recording; Blue: not in recording mode; Red: write error.

Indicator status When the indicator is on, regardless of its color, the WI-FI hotspot opens, if the indicator is in a color-changing state (slowly alternating between light and dark), the Wi-Fi hotspot closes if the indicator stays on. ,

Mounting

Electrostatic Sticker Clean the windshield and place the electrostatic sticker on the recommended area as shown in the figure below. Make sure you remove any air bubbles between the sticker and the glass.

Attach the camera mount to the windshield. Remove the protective cover from the mount and stick the mount base to the center of the electrostatic sticker. Make sure your cam body is parallel to the ground.

Press down on the mount to firmly attach it to the electrostatic sticker.

Plug the USB cable into the cigarette lighter socket. Match the cable to the top edge of the windshield and secure it along the passenger side and glove box as shown below. Connect the cable to the power adapter and insert the adapter into the cigarette lighter socket.

The cigarette lighter socket may be positioned differently in your car. The picture is provided for reference only.

Voice control

70mai Dash Cam supports voice control. When the DVR is working, you can control it with the following voice commands:

Take a photo: take a photo. Video Recording: Record an emergency video clip and save it separately in the Events folder. Silent Recording: Stop audio recording, record video without sound. Record with sound: start recording sound, including the sound inside the car. Disable WI-FI: Disable the WI-FI hotspot of the DVR. Turn on WI-FI: turn on the WI-FI hotspot.

In the following situation, voice control does not work:

70mai Dash Cam app accesses the device; indicator flashes.

Activating the camera on first use

Turn on the camera. When the DVR boots for the first time, you will hear the voice message “70mai is loading, please activate the device by connecting to your mobile phone”. At this time, the indicator flashes blue. (If the indicator is blue but always on, please press the power button to open the dash cam’s WI-FI hotspot.)

Using the app to connect to the dash cam 1. Open the 70mai dash cam app and log in to your account. 2. On the home page of the application, click “Add new DVR” and follow the instructions to establish connection with the DVR. The default password for the DVR. 12345678. 3. When you hear the prompt “Please press the power button to log in”, press the power button to accept the connection request from your mobile phone. 4. When connecting to the DVR for the first time, you will see an instruction in the application. Please read it carefully to get acquainted with the basic skills of using the DVR, as well as adjust the angle of the DVR.

Application functions

Device list If you have NOT added a DVR, the device list is empty. Click the “Add New” button or the “” icon on the right side of the title to add a new DVR. If you added a DVR, Click the device image to go to the DVR plugin page. If there are several DVRs in the device list, you can select another device by clicking on the device image.

Check for a firmware update. If new firmware is available, a red dot appears on the Firmware Update button at the bottom of the home page. Click “Firmware Update” to check the firmware update. If there is a new firmware, click “Download” to download the update package to your mobile phone. When the update package is downloaded, you need to go to the DVR module page to send the package to your device. If your device has been updated to the latest version, you can uninstall the update package by clicking the delete icon on the header of the firmware update page.

Before entering the plugins page, you must connect your mobile phone to the dash cam WI-FI hotspot. When you leave the plugin page, the connection will be automatically disconnected.

Preview Get live preview from the dash cam. You can switch to the full size preview by clicking on the “enlarge” icon in the lower right corner of the preview.

Take a picture Press the “take a picture” button to take a picture. When you hear the shutter sound and the voice prompt “The photo has been saved”, the photo has been taken and saved in both the albums of the DVR and the mobile phone.

View the dash cam album. On the dash cam plug-in page, click the “Album” icon to enter the device album. You can find videos and photos saved in the TF card. There are three subfolders in the device album:

Normal Event photo

You can play or download videos and photos when entering a specific list.

Push update package. If you downloaded the latest firmware, go to the plugin page and click the “Push Update” icon to transfer the update package to the DVR. If there are no update packages available, the “Push update” icon is disabled. When the dash cam receives the upgrade package, the indicator shows blue blinking and recording stops.

PERSONAL CENTER

On the main page of the application, click the “User” icon at the top left to enter the personal center

Change profile In the personal center, you can change your avatar, nickname, name and gender.

Control your devices You can also control your devices here. You can add a new device as well as delete an existing device.

Video recording

Normal video 1 minute duration Recording mode: loop recording

Event video 30 seconds before the current video. Recording mode: loop recording.

Photos Photo memory capacity: up to 300 photos. If your photo storage is used up, you need to manually delete old photos to free up space.

Video storage

TF card requirement

The Xiaomi 70mai Dash Cam supports standard TF card with capacities ranging from 16GB to 64GB and speed class 10 or above. Before implementation, please make sure you format the TF card inside the dvr.

All videos are overwritten, starting with the old ones, when the disk space limit is reached. Be sure to back up your footage to your phone or computer in case of an accident.

TF cards can be damaged during continuous video recording and cleaning. In this case, replace the TF card if it doesn’t work.

Make sure you are using high quality TF cards from a reputable brand. Actual write speed and capacity of low quality TF cards may be lower than stated. Videos are usually NOT saved to low quality TF cards. We do NOT accept any responsibility for such cases.

Please format it inside the DVR before inserting the new TF card. We strongly recommend that you format your TF card once every 2 weeks; otherwise, your TF card may get too slow.

Do NOT insert or remove the TF card when your dash cam is working.

TF card exceptions

If the dash cam stops recording due to TF card exclusion, the indicator light is red. The following exception states can be:

TF card capacity is less than 8GB; TF card class less than 4; Old TF card; TF card has become slow in write speed; TF Card not recognized; There are files that are NOT generated by the device; TF card format is wrong.

Source of power

Your dash cam receives electricity from the cigarette lighter socket. Use the original power cord and adapter to maintain a stable input power source. We are NOT responsible for any loss or damage caused by the introduction of a second power source other than the cigarette lighter socket, or the use of non-original power cables and adapters.

READ  DVR 70mai Dash Cam Installation

Some cars still supply power to the cigarette lighter outlet after the engine is turned off. To avoid draining your car’s battery, press and hold the power button to turn off the camera, or remove the adapter from the cigarette lighter socket. Remember to turn on the camera when you start your next ride. We are NOT responsible for any loss or damage caused by disconnecting the camera when leaving the vehicle.

Battery

The built-in battery of the DVR is only used to save the last video file when the external power supply is disconnected. DO NOT use the camera without external power supply.

DO NOT remove the built-in battery by yourself.

Stop using the device and Contact service for assistance if you encounter any of the following factors: the battery temperature is too high; the battery is deformed; the battery expands; battery fluid spills; and any other abnormal battery related incidents.

Search for the problem. Security measures

70MAI Dash Cam records video outside of moving vehicles. It cannot protect drivers and passengers from any accidents. We do NOT accept any responsibility if the user becomes involved in any traffic accident and / or incurs any losses due to product failure, loss of information or product operation.

Due to differences in vehicle type, driving preference, environment and other differences, parts of the product or all of the product may not function properly under the circumstances. Recording may not work properly due to loss of external power supply, operation in abnormal temperatures and / or humidity, collisions, damaged TF card, and other possible reasons. We do NOT guarantee that all videos can be completely saved in any situation. Images recorded by this product are for reference only.

Install the product correctly, do not obstruct the driver’s vision and DO NOT cover the airbag. Improper installation of the product may result in damage and injury.

Keep this product away from strong magnetic fields to avoid damage.

Do not insert or remove the TF card while the device is working, so as not to damage the TF card.

Use a TF card with a capacity of 16GB to 64GB and a read and write speed not lower than Class10. Format TF card before inserting it.

TF cards can be damaged after repeated use. Replace TF cards in time to be able to save videos. We do NOT accept any responsibility for any failure caused by TF cards.

The product can record and save footage from road accidents, but we DO NOT guarantee that footage from an accident can always be recorded and saved. Minor collisions may NOT be detected by the sensor; therefore, the footage cannot be placed among accident videos.

DO NOT use this product at temperatures above 60 ° C or below 20 ° C.

The battery can be discharged if the device is not used for a long time. You may be asked to reset the device time when you turn on the device again.

Do not shake or press on the product. Strong impact or shaking may cause irreparable damage to the camera.

Do not clean this product with chemical solvents or cleaning agents.

Video recorder Xiaomi 70 Mai setup instructions in Russian

Setting up the Xiaomi 70 mai dash cam car DVR.

Power button

The 70mai DVR only has one button. power button.

Press the power button to turn on the DVR.

When the dashcam is on, click the power button to turn on or turn off the Wi-Fi hotspot.

Press and hold the power button to turn off the DVR.

Press the power button three times to format the micro SD card.

Press the power button five times to reset the device to factory settings.

70mai dvr indicator

The indicator is shaped like a ring and is located around the power button.

The indicator has the following modes:

The indicator is off when the DVR is off.

When the device is turned on, the indicator lights up in the following colors:

  • Green: normal recording
  • Blue: non-recording mode
  • Red: write error

Smoothly flashing mode. When the Wi-Fi access point is on, the indicator is in a state of smooth flashing mode regardless of its color.

Flashing Mode:

  • Green Flashing: Recording emergency video.
  • Blue Flashing: Formatting the memory card, restoring factory settings, receiving a service pack, updating the firmware, waiting for a connection confirmation.
  • Red Flashing: Low battery.

Installing the Xiaomi 70 mai DVR

Clean your windshield and stick the sticker to the recommended area shown in the picture. It is necessary to remove bubbles between the glass and the sticker.

Attaching the bracket to the windshield.

Remove the protective film from the sticker and stick the bracket firmly pressed against the center of the sticker. It should be borne in mind that the body of the DVR must be parallel to the ground.

Connecting the USB cable to the cigarette lighter.

Route the cable along the top edge of the windshield and lower it down from the passenger side as shown.

Connect the cable to the power supply and plug the power supply into the cigarette lighter.

Voice control

70mai dash cam supports voice control.

When the DVR is turned on, you can voice control the following functions:

  • Take picture: Take a picture
  • Record video: Record emergency video and save it to a separate folder
  • Record without sound: Turn off sound recording
  • Record with sound: Enable sound recording
  • Turn off Wi-Fi: turn off Wi-Fi hotspot
  • Turn on Wi-Fi: Turn on Wi-Fi hotspot

Voice functions do not work when the device is being accessed or when the indicator is flashing.

Turning on the 70 mai dash cam for the first time

When you turn on the dashcam for the first time, you will hear the voice prompt “70mai boots up, please activate the device by connecting to your cell phone”. At the same time, the flashing blue indicator will light up.

If the indicator is solid blue, press the power button once to turn on the Wi-Fi hotspot.

To connect to the DVR from your phone, install the 70mai app on your phone. The app can be found in the Play Market and App Store

The first time you launch the application, you need to register. To do this, click “Sing up”.

You will see a user agreement window, which must be confirmed by clicking the “Agree” button.

Next, enter your email address and click “Get security code”. A secret code will be sent to your suite. After receiving the secret code, enter it in the application. Then enter any password, repeat the password and click Submit to complete the registration.

Now you need to click the Add device button to add the DVR to the application. In this case, the Wi-Fi access point on the camera must be turned on, as described earlier.

Next, select 70mai Smart Dash Cam

Make sure that the Wi-Fi access point of the DVR is turned on (smoothly blinking blue indicator) and click “Next”.

Now you need to connect your phone to a Wi-Fi access point, which has a name in the format 70mai_d01_xxxx. When connecting, enter the password 12345678. After connecting to the Wi-Fi point, return to the application and click “Connect”.

To configure the DVR, click “Device settings”

The following settings window will open

Also, using the application, you can update the firmware of the device, view the broadcast from the video recorder in real time, take pictures

70 mai dash cam car dvr firmware update

Click the “Firmware update” button at the bottom of the application start page to check for new firmware.

If there is a new firmware version, click “Download” to download the update package for the DVR to your phone.

Next, you need to connect to the Wi-Fi access point of the DVR, as described above, and open the DVR viewing page in the application.

Now, to update the firmware, press the button “Update” (Push update). The DVR indicator will be blinking blue during the update process.

Recommended memory card

The DVR supports standard micro SD memory cards from 16 to 64GB class 10 or higher.

Remember to format the memory card before embedding.

FAQ. How to flash 70 mai video recorder. Firmware instruction

Before updating the 70mai recorder, or as many say “firmware for the 70mai video recorder” from Xiaomi, we recommend that you read all the information presented below in this thread in full. The most crucial moment, first, let’s figure out which revision (version you have a 70mai video recorder). You can distinguish it visually by looking at your device and compare it with photos.

Only after that you download the desired file. “70mai firmware” based on the received data in the version of your recorder from the unfolding “spoilers”. And only then start flashing the device. I draw your attention to the fact that even if the 70mai registrar from Xiaomi is permanently connected to power from the USB cable, it still needs to be charged at least up to 60% before starting the firmware, in order to avoid problems !

Where can I download the firmware? Anywhere, the main thing is that you subconsciously trust the source. The official source, let’s say the original source of the files. Chinese forum XDA (copies of them also apply to w3bsit3-dns.com). You can easily find them through the XDA-DEVELOPER search engines. The links on my website lead to the cloud where I placed copies of THESE files. I do not distribute the file, but I post it for myself, since I very often flash the device of this model (to friends / colleagues), and I do not carry a flash drive with me Comilfo. easier to swing from the cloud. Before you start updating your video recorder on May 70, read the instructions above. Download the firmware file you need for 70mai in Russian with voice control. Be sure to download the correct file below and DO NOT rush to update the firmware. the process of which is described below. If you have any questions (there is access to the 70 mai firmware file via the link to the cloud), or you run into something along the upgrade path. write in a personal, I will tell you what to plug. Firmware for the Chinese version If you have a 70mai DVR (you bought it), it speaks an incomprehensible language and looks more like a meow of cats))) yes yes. This is Chinese, it still happens. inside all the menus are in “Chinese”, but in the latest firmware from the market this is often fixed. Anyway, if she meows in Chinese. This is the file you need. Download it exactly. as it is different for English-speaking “global” registrars. Study your DVR carefully before proceeding with the firmware update, find the visual difference on the stickers on the case!

Firmware for the English version If you have a 70mai video recorder arrived (you bought it), and inside all the menus are in “English”. you are clearly much more fortunate than the owners of its Chinese version. since here it is at least a little clear that some of the settings. To update the firmware, you need this file. Download it, but in any case DO NOT confuse it with the file above, as it is different for 70mai Chinese registrars. and if you mix it up your registrar becomes a useless brick. Study your 70mai DVR carefully before proceeding with the firmware update following the instructions above!

The firmware process is as follows: 0 Insert the SD card into the 70mai DVR. To format the SD card, press the round button quickly 3 times. Or format the memory card in PC, in FAT32 format

Unpack the firmware 70mai archive. on the link above in the drop-down rolls. It will contain a file and its name will be. SD_CarDV.Bin. Burn it to a blank, freshly formatted microSD card. I used 4 Gb, that’s enough.

Insert the microSD card into the Xiaomi 70 mai camera; As soon as you connect the charging wire to the 70mai DVR, the firmware will literally start immediately. Therefore, make sure that you have written a really correct firmware file to the card.!

READ  How to convert 4k to Full HD

Connect the 70 mai recorder to an external power supply; Powerbank can be used. I plugged it straight into a wall outlet for a regular charger. that’s which all their smartphones / phones and gadgets usually charge.

The 70 mai will start flashing blue. Video recorder 70 mai chirps something in Chinese, a few phrases and. The firmware process has started;

It will last no more than three minutes, and will depend on the speed of your SD memory card. After a successful update of the 70mai firmware, the device will say something in Chinese (Probably, it may NOT say. And they say this is normal, but they told me. Then 70 mai will turn itself off (the blue LED will go out)

Turn on 70 mai. the device by pressing 1 time. And hear the native Russian language. The memory card is cleared after the firmware, and there will be no file on it that you copied there. The device will create new empty folders.

Perhaps the flash drive is even formatted, but I don’t know that and it’s better to ask our Chinese friends about it. Well, that’s all. I congratulate you. You have successfully flashed your Chinese 70 mai video recorder into Russian. You can now enjoy Russian voice acting (and for some models and Russian voice control). Be sure to look into voice control (link to the topic with all the commands, but in three languages). you will like that he constantly monitors what you say.

about the author

All materials presented on the site are unique and inimitable. All rights to this content belong to the author of the resource. Any posting of content (partially or completely) on second resources and printed publications without indicating a link to the website source: www.Odesoftami.com is illegal.

Review of the DVR Xiaomi Mi Dash Cam 1S (global version).

Today in the review is the global version of the Xiaomi Mi Dash Cam 1S DVR. In fact, this is an updated version of the Xiaomi Mijia Car DVR or its logical continuation. The recorder is built on the MSC8328P chipset and the Sony IMX307 sensor, implemented using STARVIS technology, which allows you to get a clear image in low light conditions. The camera honestly shoots at 1080P (1920×1080) quality, works with the Mi Home app.

The registrar is delivered in a cardboard box covered with plastic foil with the usual design for Xiaomi products.

On the bottom of the box there is information about the product.

On the stickers in the lower right corner there is just the QDJ4032GL code, indicating the globality of this registrar model.

Specifications in more detail:

Brand: Xiaomi Model: Mi Dash Cam 1S (MJXCJLY02BY) Version: Global (QDJ4032GL) Chipset: MSC8328P; Image sensor: Sony IMX307 (STARVIS) Function: G-sensor, HDMI output, night vision, parking monitoring, voice control; Display: Ips 3.0 inch 640 360; Built-in battery capacity: Li-ion 470 mA / h; Working Voltage: DC 5V 1.5A; Lens: F1.8 6 lenses; Viewing angle: 140 degrees; NTSC 1080P (1920×1080) H.264; Frame rate 30fps; Video Output: AV-Out, HDMI; Audio: Built-in microphone / speaker (AAC) WI-FI: 2.4GHz 802.11 b / g / n (image transfer, remote control, settings, sync and share albums up to 6 meters away); Loop recording: Yes; Loop recording time: 20 min; Memory card support: TF 16-64Gb (not included), class 10 and above; Motion detection: No; Night vision: Yes; Night vision distance: 20m; Parking Supervision Yes; Compatibility: Android 4.4 or iOS 8.0 and above; Working temperature:.10-60 С; Cable length: 3.5m; Product size (L x W x H): 8.80 x 5.30 x 2.80cm; Complete set of the recorder, charger, power cable, two electrostatic stickers, two stickers, a spatula for laying a cable, an attachment bracket, a user manual (including Ch. In Russian).

Information about the features of the registrar was put on the side edge of the box.

Modest but recognizable manufacturer’s logo.

The box is made of thick cardboard and is able to protect the recorder on the way to the buyer. The black foam insert serves the same purpose.

The recorder is packed into a paper bumper, on the bottom of which there was a drawing-instructions for laying the cable in the car. How many registrars have come across, and I see recommendations on this for the first time, thought out to the smallest detail.

The rest of the accessories are stacked in the lower tier of the box.

Together with the instructions in the package, there were two electrostatic stickers, through which the recorder is attached to the car glass. One sticker spare.

I first met this type of DVR mount on the Xiaomi 70MAI model. At first I was skeptical, but my doubts were dispelled by the year of operation of this registrar. not a single case of peeling off the sticker and dropping the recorder There were no cases. secure mount.

It looks like a simple transparent film, but it keeps tenaciously on the car glass, and a recorder tripod is already glued to the outlined circle in the center. I was very pleased with the instructions for this registrar. Since the version is global, the instructions contained sections in English, Chinese, Spanish and unexpectedly Russian, for which many thanks. over, this is NOT a Google translation, and not an anecdotal puzzle, but really normal Russian.

The rest of the accessories in the kit, except for the bracket and a spare mug of double-sided tape for gluing the tripod to the electrostatic sticker, packed in separate bags.

One of the packages contained a rare thing for a set of recorders. spatula for laying the power cord under the rubber seal and trim elements of the car.

Familiar already to me from Xiaomi 70MAI single-port charging at 5 Volt 2.4 Ampere.

The tripod for installing the recorder with a rotary mechanism is very small, it will not be conspicuous and look foreign in the car. A spare round of double-sided tape in case something goes wrong.

And the last accessory. DVR power cord 3.5 meters long with L-shaped microUSB plug.

The updated version of the registrar, just like the previous one, also looks neat and is designed in an attractive style of Xiaomi minimalism.

A drawing with instructions for installing the recorder was applied to the protective film of the display. It’s simple and it’s hard to make a mistake.

On top of the case there is an on / off button, an arm lock and a power connector for the recorder. In the same photo, you can see that the lens barrel is made of metal and has a knurl.

On the underside of the recorder there are holes for the reset button and microphone, as well as a sticker with brief characteristics.

The operating mode indicator and the memory card slot are located on the left side of the case. The slot is covered with a cover and accidental loss of the card or clogging of the slot is practically excluded. The indicator glows white during shooting. In the event of an emergency, the indication color changes to red.

The right side of the case does not contain any functional elements.

For order and presentation in overall dimensions measurement results.

Assembled with a bracket, the camera is still very compact and does not take up a lot of space on the glass. Swivel mechanism allows you to adjust the desired angles.

Turning on the recorder is accompanied by a melody, and when you turn it on for the first time, the user is immediately prompted to choose one of four interface languages. English, Russian, Chinese or Spanish. Not a very large selection, but still quite global.

After selecting the language, the recorder interface will guide the user through the instructions and Presets.

Further and always after connecting the power supply, the recorder will turn on and record. If there is a memory card in the recorder, then he will ask you to insert it, but if it is necessary to install and everything is in order with it, the indicator on the side will glow white.

All control of the recorder is carried out by four touch buttons, marked with white dots under the screen. The screen itself is NOT touch-sensitive and touching the icons above the buttons will not give results.

The DVR status bar is located at the top of the screen. During recording, a red dot blinks next to the Rec message, the date and time are projected, as well as the crossed out WI-FI icon if the registrar is NOT connected to the Mi Home application on the phone. The P symbol also appears here when the parking monitoring function is activated. parking monitor. By default, video recording is silent and the microphone icon is crossed out. By touching the touch button, turn on the microphone, and the video will already be with sound.

The checkbox button activates the process of recording emergency video from a separate folder on the memory card (up to 20% of the total volume), this video can be erased only through a computer or when the folder is full and the recorder will start deleting the oldest records. Ordinary video of users can be erased at any time, or it will happen when the memory is full and the recorder also begins to replace the old video with new files. The files weigh 237 MB each, containing 2 minutes of video. Gallery icon button moves user to DVR memory folders.

Going to any folder stops video recording, which is indicated by the corresponding inscription on the screen. After returning from any folder to the gallery, video recording resumes. Files inside folders are represented by large icons.

The last touch button activates the DVR settings menu where you can turn on / off the sound when the DVR is turned on, set the time to turn off the screen after starting recording, etc. And so on.

You can set the sensitivity of the shock sensor of the recorder or turn it off completely. Taking into account the condition of the road surface, I chose low sensitivity, otherwise crossing the tram rails or falling into a small hole causes video recording to the emergency folder.

You can select the recording quality (only two options, labeled as “finished”. 1080p with a resolution of 19201080, i.e. FHD, and normal 1280 720, i.e. HD) and select the language again.

It is possible to adjust the speaker volume, view the status of the memory card and format it.

The next screen of the settings menu allows you to set the date and time, set the shock sensor sensitivity of the parking monitor function, and start the system update.

DON’T forget in the ability to reset to factory settings and view information in the software.

All of the above operations can be done from the phone by connecting the recorder to the Mi Home application. In addition, the application will become available to take a photo. For some reason, the registrar in such a function was forgotten.

To connect to Mi Home, you need to turn on the access point of the registrar (the very first item in the settings menu).

In Mi Home, the registrar should be found in the “Nearby Devices” tab. When connected, the WI-FI settings window will open on the phone, where a new network will appear. MiDashCam1S_v2_8508. When connecting to this network, you will need to enter a password, which was on the recorder’s screen. On subsequent connections, you do not need to enter a password, you just need to select the desired network.

As noted above, the application adds the ability to take photos. You can also watch the video recorded by the registrar by entering the gallery. Video recording stops again.

The settings menu item is indicated by three dots in the upper right corner of the screen, and from here you can perform the same manipulations with the recorder as through its buttons, plus check the software update and change the name of the gadget. A little later, a software update to version 1.0.5 arrived

Items related to setting up the recorder from the application completely duplicate the button manipulation option.

When connected to a computer, we can see the folder structure and photo / video. Normal video is stored in the Normal folder, in the Event folder. video in how he drove into a pit or an accident happened. Video is dropped into the Monitor folder in events immediately after hitting the car during parking (when the car, for example, stands in the yard at night).

I want to Pay attention to the fact that if you activate the surveillance mode while parking, then after it, when you need to go somewhere, this mode must be turned off, since It does not turn off automatically and event video (accident, entering a pit, etc.) Will not be saved in the events folder, but will generally be recorded in the folder for regular video, i.e. Will not be protected from erasure. In parking monitor mode, the recorder is powered by an internal battery. In case of hitting the car, the recorder starts recording without turning on the screen and without attracting attention. When the owner turns on the ignition, the recorder with a voice message and text on the screen informs about the presence of a new video in the Monitor folder.

READ  Xiaomi Mi Home Security Camera 360 Setting

The angle of view of the recorder was checked according to the following method: “We put 2 columns on the floor at a certain distance from each other, for example, 2 meters (the more, the more accurate the measurement result will be). Exactly between them we put the recorder and move it away from the line connecting the posts, watching the picture. As soon as the columns are at the very edges of the frame. we measure the distance from the recorder to the line. If b. the distance between the posts, a. distance from the lens to the line connecting the posts, then the angle = 2 arctan (b / 2a) “In my case, b turned out to be 6.95 meters, a. 2.2 meters and the angle of view of the recorder was 115.34 degrees, which is noticeably better than in 70Mai. Claimed 140 degrees. most likely diagonally.

As for the functionality, there is nothing more to add and I suggest looking at the quality of shooting.

In daylight, the registrar proved to be quite confident in fixing the situation on the road and car numbers not only in the same lane, but also in the oncoming one. over, there is distortion of the picture even in the lower corners of the frame and the license plates of the cars can be read. The change of illuminated and shaded areas is well practiced. There is sky flare, which often happened on video, filmed by 70Mai.

Since Youtube degrades the quality of the video, the link to the original.

The DVR sensor quickly adapts to video recording of poorly lit and well-lit areas.

The lack of WDR function affected only at night. There were times when the license plates on the video were overly illuminated. The main reason for this is the too bright head light of my car. However, in the corners of the frame and on the adjacent lanes, where the lighting is not so intense, the license plates are read quite normally.

In all cases, the shooting quality was set to maximum.

The registrar does not take a photo at the level of a DSLR, but it is quite normal for the gadgets of its sector.

On the glass, the recorder Takes up not much space, and does not interfere with the view and remain unobtrusive from the street.

I can only compare this registrar with 70Mai. In terms of the quality of the daytime picture, they are comparable, but the processing of details in the corners of the frame is slightly better in the Xiaomi Mi Dash Cam 1S. The 1S also copes better with transitions from poorly lit to well-lit areas; on a sunny day, there is an unnatural flare of areas of the sky. The presence of a screen A definite plus, i.e. The recorder is completely autonomous. Product support is ongoing and software updates are available. A parking monitor is provided and operates normally. Appearance, build quality I DO NOT take for consideration. habitually neat for Xiaomi. Overtemperature protection is provided, which disconnects the recorder from the power supply.

Installation of the rear video recorder Xiaomi 70Mai, for example Lada Vesta SV Cross

Hello friends! Today I will show you how I installed and connected the rear DVR to my Lada Vesta SV Cross.

For those who like to watch videos, there is a video review on YouTube:

As a rear DVR, it was decided to use a compact DVR from Xiaomi, namely the Xiaomi 70Mai. It is small, without a screen, and when unpacking it, I said that it should not be in the front, but just behind. Well, my hands got around and did. I bought it HERE all offers HERE

Since the rear window gets dirty quickly on the station wagon and hatchbacks, it must be placed in the range of the rear wiper.

Well, now the actual installation. Remove the driver’s door seal.

Then the rear door seal.

This is necessary in order to run the power cable under the ceiling trim without removing it.

Next, we remove the end caps of the panel, under which I brought out the power cable for the recorder from the alarm with two USB ports. This is where you need to stretch the cable from the rear recorder.

I have a video about the installation of this block on my channel:

Well, then we stock up on patience and start twisting. The process, of course, could not be the most fun, but I did it once and my head does not hurt. The cable will not rattle, fray and, accordingly, over time, a shorty will NOT appear or just a break. So we are NOT stingy and cool.

10 minutes and the cable is ready. Installation can begin.

We start with the front pillar. It can be removed, but it was decided to disassemble the interior to a minimum. The cable was simply tucked neatly under the rack without removing it.

In order to stretch the cable from the front to the rear door under the ceiling without dismantling it, you will need a piece of wire.

Then we tie a cable to it and just stretch it.

That’s all, the cable has passed and the ceiling is NOT touched.

Next, the cable must be pulled to the fifth door under the ceiling, preferably again without dismantling it and bring it out through the corrugation under the door trim and to the location of the recorder.

To do this, you will have to pull off just a couple of clips from the ceiling, you can NOT remove it, but then it will be very difficult. We slightly bend the ceiling and stretch the wire from the fifth door to the rear passenger.

We tie the cable to the wire and pull it to the fifth door.

Well, here’s the cable and stretch back almost indiscriminately.

The cable lies on a soft ceiling, so also turn it with electrical tape, its additional fixation is NOT required.

We put the seals in place.

The salon has been completed. Fast, no dust or noise. For everything about everything for 10 minutes.

Now it is necessary to remove the central part of the fifth door trim, without dismantling the cable under it cannot be pulled.

Next, you need to pull the cable through the corrugation and bring it under the removed casing. For pulling, wire is also needed, and for convenience it is necessary to pull off the corrugation O-rings from their regular places, otherwise the wire, and even more so the cable does not want to pass.

Well, actually we stretch and pull the cable.

That’s all, we put the ceiling clips and we will NOT disturb the ceiling itself anymore.

You can also put in place all previously removed seals.

It is better to fix the excess of the stretched cable with ties, for example, to other wires, so that it does not dangle there much.

The excess cable turned out to be no more, I did not cut it, on the screeds the extra piece will safely hide under the plastic sheathing. In my opinion it turned out quite well.

Well, actually the installation of the skin itself.

As you may have noticed, I did not wind the electrical tape to the end, but only with a small protrusion from under the plastic, so that it would NOT rub the cable with its butt, and so that the visible part of the cable was more neat.

xiaomi, 70mai, dash, installation

The recorder was specially hung low, in the wiper’s area, otherwise in spring and autumn it will only remove dirt on the glass.

You can’t even see it from the outside on the tinted glass, that’s good.

The only thing left to do is to connect the cable to the previously prepared USB port. Here I put the unit on two ports, watch the video about its installation, if interested.

The cable is connected, we hide the excess and you can close the end cover.

We put the plug in place.

Well, that’s all set. The recorder is installed, connected and paired with the front one. They are launched from me through the alarm. They also both turn on for five minutes when an alarm is triggered or when a warning signal from a light hit to the body. If someone hooks on in the parking lot, they will NOT go unnoticed. A convenient and useful thing. I talked about this in more detail in the video about installing the front DVR. So the recorder does not have a screen, a big plus, at night nothing shines in the mirror and does NOT interfere. All control takes place from a smartphone via WI-FI.

This is how in half an hour with smoke breaks and minimal disassembly of the cabin, you can install a rear recorder. As you can see, there are extra wires on the surface, everything is laid in a corrugation, respectively, the cable is not threatened with chafing, bending and breakage, one might say factory assembly. I am very pleased with the result.

As for the presence of tinting on the glass, of course it affects the result, in the daytime it is almost imperceptible, not critical, the picture is quite readable, the numbers are visible, and in general it is worthy. For a general understanding of the traffic situation, more than enough.

But with the arrival of night, the picture deteriorates. You can’t see a damn thing through the toner. Only bright lights and nothing else. The license plates can be seen only at a distance of no more than two or three meters. In general, for the night, the option with toning of course could not do. But because of this, I’m not going to take off the tinting, and even more so to cut out a piece of tinting for the recorder, I can’t go for it. So if you don’t have tinting and are NOT going to glue, then you are more fortunate than me.

Is it rational or not, the installation of the registrar on the back, I will not argue, firstly, I had this registrar idle and it was a sin NOT to use it. Yes, toning completely kills night photography, but at least during the day everything is fine, it’s also better than nothing. Yes, and the installation, as you have seen, cannot be easier. In general, I’ve been skating with him for about a month and I can say that I have never regretted installing it. DOES NOT interfere, do not ask for food, but the record is.

And by the way, no matter how dark toning is, drivers driving behind, it is, in principle, noticeable, and believe me, this is a very deterrent factor for those who want to sit on their tail, blink, blink and cuddle at traffic lights and rise. I think it’s unpleasant to sit behind the wheel and understand that you are being filmed head-on. The behavior of the cars behind me changes noticeably from aggressive to calm immediately after changing lanes behind me in my lane. So in any case, the recorder in the back is, as for me, always good in every sense. I have set, I am satisfied.

Be careful friends on the road, be polite, and remember, they are waiting for us at home! And when the roads become calmer, perhaps we will no longer need these recorders.!