Rear view cameras

• Brand: Falcon
• Model: RC120-SCCD
• Purpose: rear view
• Type: threaded mount
• Color system: NTSC
• Photosensitive Element: SCCD
• NTSC Pixel Number: 720×576
• Horizontal viewing angle: 170 degrees
• Minimum illumination: 0.05 Lux
• Parking markings:

• Sensor. color, SONY CCD;
• Viewing angle. 170 degrees;
• Light sensitivity. 0.1 lux;
• Resolution. 728×582 / 728×512;
• Parking markings.

• color sensor. SONY CCD;
• viewing angle. 170 degrees.;
• photosensitivity. 0.01 lux;
• resolution 728582/728512;
• moisture protection. IP66;
• 520 TV lines;
• parking lines;
• PAL / NTSC.

• Sensor. color, CMOS;
• Viewing angle. 140 degrees;
• Light sensitivity. 0.2 lux;
• Resolution. 728×582 / 728×512;
• The degree of moisture protection. IP68;
• The number of TV lines. 480;
• Working temperature. 30 70;
• Power cord length. 120 cm;
• Video signal wire length. 600 cm;
• Parking markings.

• Sensor. color, CMOS;
• Viewing angle. 140 degrees;
• Light sensitivity. 0.2 lux;
• Resolution. 728×582 / 728×512;
• The degree of moisture protection. IP68;
• The number of TV lines. 480;
• Working temperature. 30 70;
• Power cord length. 120 cm;
• Video signal wire length. 600 cm;
• Parking markings.

• color sensor. SONY CCD;
• viewing angle. 170 degrees.;
• photosensitivity. 0.01 lux;
• resolution 728582/728512;
• moisture protection. IP66;
• 520 TV lines;
• parking lines;
• PAL / NTSC.

• color sensor. SONY CCD;
• viewing angle. 170 degrees.;
• photosensitivity. 0.01 lux;
• resolution 728582/728512;
• moisture protection. IP66;
• 520 TV lines;
• parking lines;
• PAL / NTSC.

Mercedes Sprinter. Rear View Camera Install

• Sensor. color, CMOS;
• Viewing angle. 140 degrees;
• Light sensitivity. 0.2 lux;
• Resolution. 728×582 / 728×512;
• The degree of moisture protection. IP68;
• The number of TV lines. 480;
• Working temperature. 30 70;
• Power cord length. 120 cm;
• Video signal wire length. 600 cm;
• Parking markings.

• color sensor. SONY CCD;
• viewing angle. 170 degrees.;
• photosensitivity. 0.01 lux;
• resolution 728582/728512;
• moisture protection. IP66;
• 520 TV lines;
• parking lines;
• PAL / NTSC.

• Sensor. color, CMOS;
• Viewing angle. 140 degrees;
• Light sensitivity. 0.2 lux;
• Resolution. 728×582 / 728×512;
• The degree of moisture protection. IP68;
• The number of TV lines. 480;
• Working temperature. 30 70;
• Power cord length. 120 cm;
• Video signal wire length. 600 cm;
• Parking markings.

• dynamic parking markings;
• sensor. color, SONY MCCD;
• power supply. 12V;
• viewing angle. 190 degrees;
• photosensitivity. 0.1 lux;
• resolution. 1280720;
• the degree of moisture protection. IP68;
• number of TV lines. 720;
• PAL / NTSC;

• dynamic parking markings;
• sensor. color, SONY CCD;
• power supply. 12V;
• viewing angle. 170 degrees;
• photosensitivity. 0.1 lux;
• resolution. 728582/728512;
• the degree of moisture protection. IP68;
• number of TV lines. 520;
• PAL / NTSC;

An indispensable thing for novice drivers, as well as for already experienced car enthusiasts, is a rear view camera. This tool allows you to see what is happening behind your car, which can be quite difficult for most drivers. There are different situations when what is happening on the road is quite difficult to see through the mirrors, but you don’t want to become a victim or cause an accident. Therefore, the best way to protect yourself and your car is a rear view camera.

The rear view camera gives you the opportunity to fully imagine the situation, which means you will forget about the problems and will always feel confident behind the wheel of your car. Modern cameras have a viewing angle of up to 180 degrees. Therefore, if you decide on such a purchase, then you will definitely not regret it.

2 Installing a rear view camera is a simple and effective way

Regardless of the body type of the LADA Granta model, the rear view camera above the license plate is installed using the same technology. So, carefully remove some of the trunk trim. First. the brake light pad, which is fixed on clips, then. the side part on clips and screws, and only then the main trim. Now, using a Phillips screwdriver, unscrew the 6 M8 bolts around the perimeter, on which the pad is held.

Next, you should mark the installation site, it is best to place the camera in the center of the lining so that it is adjacent to the license plate cover. In this case, the view will also be on the edge of the bumper, which will greatly facilitate the parking process. Now, using a drill, you need to carefully drill a hole for the mount and fix the camera (depending on the type of mount) on a nut and washer. Using electrical tape, connect the wires from the device to the wires from the license plate light and install into the factory plug.

You can pull the wires into the passenger compartment through the standard corrugation, but this process is quite laborious, since the corrugation is narrow and not adapted for additional wires. At this stage, we recommend using a thin flexible brake cable, like those used on bicycle brakes. As practice shows, with it the wires stretch much easier and faster.

Device selection

When choosing a view camera for LADA Liftback, the following characteristics should be taken into account:

• Constructive performance. The camera can be mounted on the rear bumper or integrated into the boot lock cylinder. In rare cases, the device is placed behind a rear window. This installation method may affect the quality of the view.
• A method of connecting to a device that receives information. Rear view camera can display the image on the monitor located on the dashboard or built into the mirror.
• Signal transmission method. It can be carried out via a cable pulled through the passenger compartment or using radio waves. The latter method does not require removing the casing, however, the signal quality may decrease.
• Optical system parameters. The viewing angle should be 120… 170 °. At high values, the image may be distorted.
• Matrix type. CCD devices provide better visibility at night, but they are slower to read information. CMOS sensors are very fast, but they cannot function in complete darkness.
• Color system. All cameras transmit color images. It is converted to PAL or NTSC chroma on output. It is recommended to select cameras that support both standards.
• Mirroring capability. This parameter ensures the correct perception of the image. The function is disabled in most devices.
• Dust and moisture resistant. There are 3 degrees of protection, depending on which the device can withstand short-term or long-term immersion in water.
• Photosensitivity. This parameter reflects the ability to work in the dark, it is measured in lux.
• The presence of parking lines. A good camera should overlay a rectangular grid over the image. This helps to better orientate when reversing.

Do-it-yourself installation of a rear-view camera on a Lada Grant Lux liftback or sedan

Installation of a rear view camera on LADA Granta is carried out independently or with the help of a specialist. Video devices are not included in the standard package, so they will have to be purchased separately. When choosing a rear view camera for Granta Liftback, you need to take into account not only the cost, but also the technical characteristics of the equipment.

1 How to choose a good camera and a convenient installation method?

There are a huge number of rear-view camera models on the market that are suitable for both Grant and other VAZ models, including the LADA Priora and LADA Vesta models. We are talking about universal versions of domestic and Chinese production. When choosing a camera, you should pay attention to its packaging, the presence of a good viewing angle (at least 170 degrees), the quality of the matrix, parking lines and the manufacturer’s warranty. On average, a rear-view camera costs between 1200-2000 rubles. When it comes to installation methods, there are three most common options.

The first method, which we will describe in detail, is to install the device instead of a license plate light.

The third method is to install the camera directly into the rear bumper using a technology similar to installing a parking sensor. In this case, the ideal viewing angle and camera height are obtained, but accessories of this type are slightly more expensive, while installation becomes much more complicated, since you will have to remove the bumper and drill it. In addition, with this method, it is more difficult to drive and connect the wiring, but at the same time the camera will look more organic on the car body. Which of the ways to choose is up to you, we will consider the simplest and most common way to install over a rear license plate.

Where and how to install

The video system installation procedure includes the following steps:

• Choosing a place to fix the monitor. If the owner does not want to display information on the radio tape recorder, use a fold-out monitor installed in an arbitrary area. The head unit is mounted in the trunk.
• Preparation of tools. To install the camera, you will need screwdrivers with different attachments, pads with cables and standard adapters.
• Dismantling work. Before starting the installation of the camera on the LADA sedan, remove the thresholds from the doors on the left side, fold the rear seats and remove the trunk lining.
• Wiring. The cables from the central part of the console to the trunk are pulled through the regular place of the radio, the lower part of the torpedo, the sills and the pillars of the rear door.
• Fixing the parking sensors. You can install the camera on the spoiler, this is done by drilling a hole. The video sensor can also be put on the license plate.

INSTALLATION

Most often, a rear-view camera is placed above the license plate (on an overlay called a “saber”). This arrangement is the most successful from the point of view of the view, the camera is not striking and there is no need to remove the bumper. First, remove the trunk lid trim, and then the saber, which is held by 6 M8 screws.

Determine the best location for the camera and drill a hole there. We fasten the accessory on the back with a nut.

We lay the wires from the camera into the trunk through regular corrugations.

Best and Cheap Android stereo for your car | installation | Reverse camera connection | DIY

It is more convenient to pull the wiring into the front of the car under the rubber seal of the headlining. Then we drag it under the dashboard to the back of the radio. To remove the MMC, you will first need to dismantle the panel cladding.

Connection

General wiring diagram for rear view camera:

In the trunk, we connect the camera to the rear light wiring:

• 12V to green wire (reverse)
• “Mass” to black

We connect the miniISO connector to the radio tape recorder, the arrangement of the wires in the blue block is as follows:

• Ground (outer part of the tulip) of the connector to pin 16.
• Plus (center) of the connector to pin 19.

It is worth noting that if the MMS was installed on the car in the “norm” or “standard” configuration, then it will be necessary to additionally bring 12V from the reverse gear to the A1 connector of the radio.