Restoration on “Hyundai IX35

The crossover is powerful and stylish, but when the rear view camera “Hyundai” does not work, there is no need to talk about the normal functioning of the road handsome man. The device is mounted in a plastic molding near the license plate lights. The bottom of the molding is a landing area for a video camera. Wet weather and dirt do their job. moisture collects and leads to malfunctions, remaining in the case for a long time.

About the principles of purchase

Experts advise considering the following features of different types of cameras:

Rear view camera does not work: reasons, how to identify a breakdown

If the rear view camera in the car does not work, there is no serious reason for despair. The situation is fixable. The main thing is to find out the reasons and deal with the problem in time. Let’s analyze the most frequent breakdowns and the possibilities of their correction using the example of “Hyundai IX35”.

How video information is transmitted

Let’s talk in simple terms about the principles of the camera. Before determining the reason why the rear view camera does not work, it is worth knowing the principles of its operation. Video transmission is possible in two ways:

• The video cable runs to the monitor on the dashboard. The wire is routed through the passenger compartment. In this case, the signal is transmitted with high accuracy, without being subject to radio interference. The only negative point is the need to disassemble the interior trim.
• There is a more convenient wireless installation method. Information is transmitted over the radio, but the transmission range is feasible only at a distance of 15 meters.

Installation of the system is quite expensive, so some motorists prefer to carry out the procedure on their own. Consider why the problem happens when the rear view camera is not working? How to quickly solve it?

Secrets of adjustment

Having installed the device, you have to configure it. The task of the car owner. adjust the parking guidelines. To do this, you need a block about two meters long. There should be a distance of one meter from the rear bumper to the bar. The edges of the block should protrude from the sides of the car at an equal distance. Next, you need to get behind the wheel, turn on and off the side lights. The next step is to enter the menu and select your brand of device.

After activating the video camera, the steering wheel should be turned first to the right side until it stops, then to the left. On the screen, you must click on the mark “next”. The monitor will give out a rectangular outline.

After that, you need to use the regulation keys: you need to achieve the position of the bar exactly in the center on the display. The work ends with confirmation. A new disassembly will require updating the settings and doing the same manipulations. Which of the manufacturers takes pride of place in the popularity ratings?

How to repair rear-view cameras

The owner of the vehicle has two ways: to send it for repair and to adjust the device on its own. If the machine or the installed camera is under warranty, then it is recommended to contact the technicians who know why the rear view camera does not work. Service work will not deprive the car warranty. the car owner will benefit in this. You can try to fix a car that has come out of the warranty period on your own. What can be done, consider the example of “Hyundai ix35”.

Briefly about the technical device

Most common problems

The device can be built in different places: in the trunk handle, license plate light, in the cabin. The owners of the latter were more fortunate than other road users, since such cameras rarely break. This can be explained simply. there is no influence of the external environment in the cabin, no aggressive chemicals used in car washes. Why isn’t the rear view camera working? The main enemy of this device. water.

Liquid ingress leads to the inability of the camera to function normally, to distortion of the information displayed on the screen. Often, auto mechanics are faced with the problem of muddy pictures or an inoperative apparatus. The culprit for such incidents is the liquid that has seeped inside. What are the ways to fix the problem?

Secrets of adjustment

Having installed the device, you have to configure it. The car owner’s task is to set up the parking guidelines. To do this, you need a block about two meters long. There should be a distance of one meter from the rear bumper to the bar. The edges of the block should protrude from the sides of the car at an equal distance. Next, you need to get behind the wheel, turn on and off the side lights. The next step is to enter the menu and select your brand of device.

After activating the video camera, the steering wheel should be turned first to the right side until it stops, then to the left. On the screen, you must click on the mark “next”. The monitor will give out a rectangular outline.

After that, you need to use the regulation keys: you need to achieve the position of the bar exactly in the center on the display. The work ends with confirmation. A new disassembly will require updating the settings and doing the same manipulations. Which of the manufacturers takes pride of place in the popularity ratings?

About the principles of purchase

Experts advise considering the following features of different types of cameras:

How to repair rear-view cameras

The owner of the vehicle has two ways: to send it for repair and to adjust the device on its own. If the machine or the installed camera is under warranty, it is recommended that you contact the technicians who know why the rear view camera does not work. Service work will not deprive the car warranty. the car owner will benefit in this. You can try to fix a car that has left the warranty period on your own. What can be done, consider the example of “Hyundai ix35”.

How to replace the camera on a Hyundai

If the rear view camera does not work on the Hyundai IX35, it is not necessary to install the original models, since it is not forbidden to use analog modifications. For this, it is important to select a product with the most identical properties. It is optimal to purchase a variant with a plastic case. The hermetically sealed unit does not corrode. The bottom point of the molding can be covered with glue and sealant, then water will not penetrate the fixture board. You can coat the housing with butyl rubber sealant. In some situations, the camera can be salvaged. To do this, it is disassembled, cleaned, dried.

Restoration on “Hyundai IX35

The crossover is powerful and stylish, but when the rear view camera “Hyundai” does not work, there is no need to talk about the normal functioning of the road handsome man. The device is mounted in a plastic molding near the license plate lights. The bottom of the molding is a landing area for a video camera. Wet weather and dirt do their job. moisture collects and leads to malfunctions, remaining in the case for a long time.

Another reason why the rear view camera does not work on the IX35 is corrosion and oxides. A good half of the part is made of aluminum alloy. It is highly oxidized. Most often this happens through and through. The electrical board becomes unusable, so there is no point in trying to repair something. Only replacement remains.

How video information is transmitted

Let’s talk in simple terms about the principles of the camera. Before determining the reason why the rear view camera does not work, it is worth knowing the principles of its operation. Video transmission is possible in two ways:

The video cable runs to the monitor on the dashboard. The wire is routed through the passenger compartment. In this case, the signal is transmitted with high accuracy, without being subject to radio interference. The only negative point is the need to disassemble the interior trim.

There is a more convenient wireless installation method. Information is transmitted by radio, but the transmission range is feasible only at a distance of 15 meters.

Installation of the system is quite expensive, so some motorists prefer to carry out the procedure on their own. Consider why the problem happens when the rear view camera is not working? How to quickly solve it?

Rear view camera does not work: reasons, how to identify a breakdown

If the rear view camera in the car does not work, there is no serious reason for despair. The situation is fixable. The main thing is to find out the reasons and deal with the problem in time. Let’s analyze the most frequent breakdowns and the possibilities of their correction using the example of “Hyundai IX35”.

Briefly about the technical device

Problem options

Consider the main types of problems that may arise when handling this car gadget:

• The rear view camera does not show the image automatically (does not start working when reversing);
• The device does not respond at all, does not turn on, there is no signal;
• The picture is cloudy, dirty, foggy;
• The image is mirrored or inverted. a frequent glitch with Chinese devices;

• The rear view camera transmits a blue screen (or black, white) to the monitor;
• Noisy picture (blinking or flickering);
• The gadget works, but displays the markup incorrectly.

The rear view camera does not turn on and does not work: the patient is alive?

In this post, we will explain why the rear view camera sometimes does not work in the car. By the way, this is a very moody gadget! There are many reasons why it can stop functioning, from weather effects to internal problems. We will try to give all the existing explanations, and, of course, indicate ways to solve each problem.

First, a little advice! If you are the owner of a new rear view camera that has not expired the warranty period, but it has stopped working, it is better to entrust the search for the cause of the malfunction to the specialists of the service center.

But, it is better to first try to find the malfunction of an old rear-view camera yourself. It is quite possible that you will be able to solve the problem with your own hands, without costs and strong hassle.

Do-it-yourself repairs

Next, proceed to the troubleshooting instructions. Stick to our algorithms, and you may not have to go to specialists.

• First, let’s look at why the rear view camera doesn’t automatically turn on. That is, yesterday the device worked normally, but today the screen stopped showing.

• Most likely, the gadget has stopped receiving power from the source. As a rule, it is connected to a reversing lamp. As soon as the automatic transmission turns on the reverse gear, voltage arises, the lamps light up, the camera starts automatically. If the lights are burnt out, the camera may malfunction as well. To eliminate this dependence, the optical device is connected to the reversing lights through a relay with a constant current from the cigarette lighter.
• Another option. the contacts could come off and the device was disconnected from the gearbox sensor. It is necessary to check the regulators, restore contacts, and sometimes even replace the sensor. And yes, do not forget to first check the voltage with a multimeter. it should be 12 volts.

• If the rear view camera does not work, it says “no signal”, the reason may be interference from other electronics in the cabin. Try not to turn on simultaneously with our device other devices that operate in the frequency range of 2.2-2.5 GHz (wireless networks);

• If the rear view camera works, but is buggy when transferring the image to the monitor, the solution will depend on the type of problem:

• The flashed picture. The sun is shining into the lens and the image is too bright. This factor, as you understand, cannot be corrected. Unless, look for another parking location;
• Cloudy or foggy image. If the camera stops showing clearly, then dirt, dust or moisture has got inside the eyepiece. The gadget is carefully dismantled, disassembled and cleaned (dried). Use soft rags, brushes, cotton pads. And for the future, you should think about buying protection against dirt and water for the camera;
• Mirror or inverted transmission. Perhaps the gadget was originally installed incorrectly (upside down) or configured. First, try adjusting the settings in the car’s audio system. To turn off mirroring, you need to deactivate the MIR option, to change the orientation of the picture, adjust the FLP option. Sometimes the physical rotation of the eye 180 degrees helps to solve the problem.
• The camera shows delayed, blinking, or flickering violently. The most common cause is incorrect installation. Loose fixation leads to vibration of the device when the engine is running. As a result, the image is rippled. Check that the device is securely attached to the car. Another explanation is damage to the integrity of the cables or poor insulation of the contacts. You will have to dismantle and fully check the electronic components of the device.

• When the rear view camera is turned on, a black, white or blue screen appears on the recorder. This is the most unpleasant case, most likely the cause of which is a software failure. The gadget needs new firmware (software). It is advisable to entrust the solution of this problem to the masters of the service center;

• The rear view camera is broken due to mechanical impact. Let’s say you dropped it, hit it, hit it. Alas, the repair of its components, most likely, will cost more than a new device.
• The rear-view camera on the mirror stopped working normally (any manifestations that did not exist before). blinks, turns off in the cold, does not turn on or turns on every other time, etc. Poor signal quality may be the culprit. The device will have to be dismantled, carefully disassembled, cleaned the contacts, removed dust from the microcircuit, cleaned oxidized areas, re-soldered the damaged elements of the board (if they are detected visually), etc.

Reasons and solutions

Let’s move on to the reasons why the rear view camera does not work. All of them can be divided into three groups:

2017 Honda Ridgeline. Backup Camera Stopped Working (Wiring Destroyed)

• Problems with power supply, violation of the integrity of wires and contacts. The problem could arise after self-pinout or over time;
• Incorrect installation. The place of installation has a great influence on the durability of the gadget. So, if the device is installed inside the passenger compartment, it is less susceptible to environmental factors (moisture, dust, frost), but it reacts more strongly to electromagnetic interference from other automotive equipment;
• Mechanical damage to external or internal elements of the device.

Dismantling stages

So, we have listed why the rear view camera on the radio tape recorder may stop working. Some of the problems are solved by dismantling the device. Let’s see how to do it right:

• Disconnect the power cable;
• Unscrew the nuts securing the device to the car. If necessary, remove the casing or body elements;
• Wipe the outside of the device with a soft cloth, remove traces of rust and dust;
• Disassemble the case carefully;
• Dry the components from moisture;
• Inspect the seals (rubber bands), if necessary, replace them;
• Check the integrity of the internal elements of the device. the board, the cleanliness of the contacts, the presence of oxidized areas. Remove dust with a brush, brush off corrosion;
• Replace damaged sectors by re-soldering (if you can);
• Assemble the gadget in reverse order and install it on the car.

The device now needs to be re-calibrated and configured. If, after all the manipulations, the rear-view camera still turns off, does not work, dazzles or does not transmit a normal picture to the monitor, alas, you will have to contact the specialists. They will perform professional diagnostics and quality repairs, if the latter is possible.

Rear view camera does not turn on automatically

The classic equipment connection scheme provides for connecting the device to a reversing lamp. The voltage appears when the reverse gear is turned on, but in the presence of a burned-out light bulb, the electronics work intermittently. To avoid such problems, power must be connected to the taillight through a DC relay from the cigarette lighter. The camera may stop turning on and working if it is disconnected from the gearbox sensor due to an unreliable connection of the contacts. To fix the problem, you will need to perform a connection check.

If the device writes no signal, does not work, freezes, glitches or turns off, the reason may be due to the presence of interference from phones or other electronic gadgets. It is not recommended to turn on equipment that works with a wireless network near car systems. Impact of the environment. with dirt and dust getting inside the case increases the likelihood of breakdowns. Bright light from the sun shining through the lens may light up the screen image.

Rear view camera fogged up

A cloudy display may be caused by dirt, dust, and moisture on the lens. Weather conditions with high humidity and temperature parameters cause fogging of the rear view camera. Dirt can block all or part of the lens. As a result, the screen shows dull, individual elements of the image are poorly viewed. Eliminating such problems will not be difficult. The lens is easy to clean with a soft, clean glass cloth.

Rear View Camera Shows In Mirror Image: How To Fix

Many drivers face problems when the rear view camera shows the image upside down, flips or flips the image. The reasons for such malfunctions may be associated with improper setup and installation of the device, the choice of an inappropriate monitor. To reverse the picture and remove specularity, you need to change the settings in the MMS. To do this, go to the menu and disable the Mirror option. In some cases, you need to open the case and turn the eyepiece 180 °.

If these manipulations do not help and the monitor continues to work in a mirror image, then you will need to make changes to the control scheme. Elements involved in changing the orientation of the picture usually have special markings. The option labeled FLP makes it possible to rotate the picture in the opposite direction in the vertical direction, and MIR helps to get rid of mirroring. To obtain a normal image of the picture, you must disconnect the corresponding jumpers.

Rear view camera ruffles

Ripples on the screen are common problems with incorrect installation of the gadget. The image may be severely rippled or cloudy, the product may not function properly, and it may detect markings and distances. The reason is associated with strong vibration of parts when the engine is running. To eliminate the defect, it is necessary to ensure tight fixation and reliable fastening of the equipment.

What to do if the rear view camera has a black, white or blue screen

A black, blue, or white screen on the monitor indicates imaging problems. In such cases, the camera does not work due to software problems and to fix them, you will need to flash the device. It is better to entrust equipment repair to specialists who will diagnose the malfunction, establish the exact reason why the camera does not show and choose the best way to eliminate it.

Why the rear view camera does not work: malfunctions

The reversing camera can be installed in several places. on the trunk handle, in the license plate frame, on the bumper or inside the passenger compartment. Devices installed in the cabin are less susceptible to adverse effects of moisture and other external factors, therefore they work more stably. Most often, malfunctions of outdoor gadgets are caused by moisture penetration into the device, which can cause image defects or a complete failure of the electronics. Consider the main types of malfunctions, why the rear view camera does not work and how to solve problems.

Blinking rear view camera

Flickering and blinking of the screen may be due to poor signal quality. To eliminate the problem, it is necessary to check all the contacts of the wires, make sure that the cable connections are intact and that there are no insulation faults. In the presence of more complex breakdowns, if the camera has completely failed, you will have to check all the electrical equipment. The process consists in dismantling and disassembling equipment, cleaning contacts and boards.

If your camera stops working, you can find and fix the breakdown yourself. Repairs are made according to the following scheme:

• before dismantling the equipment, check the power supply of the device using a special tester, the voltage should be 12 volts;
• disconnect the power cable;
• unscrew the fastening elements and remove the equipment;
• clean the gadget with a soft cloth, remove traces of rust and oxidation from the power connectors;
• remove the body, check the condition of the gaskets and, if necessary, replace them;
• inspect and clean all parts from dust;
• check the working board for swollen capacitors and damaged elements, replace the failed parts by soldering;
• assemble the gadget in reverse order.

After installing the electronics in place, it is very important to correctly adjust all settings and check the equipment operation. If, after all the above manipulations, the device still does not work, it is better to seek qualified assistance at the service center.

Repairs

If malfunctions appear after installation, you should evaluate the reliability of the cable connection. The basic cable length is 3-5 meters. This means that it can be deformed or damaged during installation.

If the picture quality is lost when the reverse gear is turned on, it is possible that the power supply of the device was connected to the pulsating signal of the lampshades. To eliminate the defect, you need to align it by separating the capacitor from the device using a diode.

If the camera was connected using a video interface, and the picture shows poor quality, it is enough to revise the settings mode.

With visible distortions of the picture, one should look for a problem in the incompatibility of the standards of the multimedia system. If they do not match, you need to choose another camera model or use a converter.

By adhering to these rules, you can avoid many problems in the operation of the rear view camera. If after following these steps the problem persists, you will need the help of a specialist.

But when choosing a master, it is better to give preference to proven auto repair shops, which are trusted by many buyers. Otherwise, the questionable installer will not solve the defect and will only make you waste time and money.

Dismantling and disassembly

There are several options for the development of events if the rear view camera stopped working. The first involves contacting a car repair shop or an official service center, the second is fixing the problem with your own efforts. If the device was purchased recently, and its warranty period has not yet expired, it is advisable to take it to professional craftsmen. In the absence of a guarantee, it is much cheaper and easier to restore the system yourself.

Even an inexperienced driver can get rid of breakdowns and camera errors. To do this, you need to know the basic principles of the system, the specifics of breakdowns and dismantling. Most of the models are disassembled according to the following principles:

• If the device is not able to automatically start or does not work at all, you will have to dismantle the entire casing.
• The first step is to remove the small panel at the top where the fasteners are. They are removed to remove the main part of the skin. Under the skin layer there are nuts securing the trunk handle. Four self-tapping screws are used to mount the camera. Two are for the device itself, and two more are for fixing the connector.
• If there are traces of corrosion on the radar surface, it is necessary to get rid of them, and only then proceed to the next stage.
• Self-tapping screws are used to connect the body. When dismantling, you need to be careful, because they undergo oxidation.
• If moisture gets under the case, you will have to dry it. To do this, it is enough to clean the surface with a brush and then cover it with varnish to protect it from moisture.
• Many chambers have two spacers. One of them is located on the eyepiece of the camera, the second is located at the joints between the plastic parts and the body. If the gaskets have been deformed, they will have to be replaced.
• The assembly of a working camera is carried out according to the reverse principle. Before this, you need to process the joints with a hermetic composition.

Why does not it work

When choosing a place for mounting a rear view camera, three options are considered:

• Trunk handle.
• Number illumination frame.
• Interior of the car.

According to statistics, many camera malfunctions are noticed when it is installed inside a car. This is due to the intense influence of environmental factors that cause an increase in the level of moisture. There are also mechanical loads and other influences in the cabin.

Nissan Backup Camera Problem Fixed

Any contact of the device with liquid leads not only to the failure of the system to work, but also to significant defects in the picture. Car owners often turn to a service center due to poor image quality or the appearance of spots on the screen. This problem is due to moisture getting on the lens of the device.

If the camera stops working, the possibility of a power outage is possible. When self-installing the system, mistakes are often made in connecting it to the energy source, which entail the refusal of the device to work.

Why does the rear view camera not work when reverse gear is engaged?

Many drivers become anxious when they notice that the rear view camera is not working. But if you take the right measures and start a system recovery, the problem can be fixed in a short time.

Adjustment

Sometimes the picture quality is lost after driving in rainy or snowy weather, visiting a car wash or changing the mode of the parking system. But not all drivers know how to adjust the device and check its functionality. When adjusting the camera, follow these instructions:

• First you need to take a bar, 2 meters long, with sides of 2-3 cm.
• Then it must be placed at a distance of one meter from the center of the rear bumper, making sure that the edges of the structure protrude from the sides of the car.
• Next, you should get into the vehicle and open the settings menu. You may need to carry out other manipulations by turning on and off the lights of the dimensions.
• Then you need to open the camera settings and select the model of your car. After activating the camera, it remains to unscrew the steering wheel to the right and then to the left. such manipulations will allow you to adjust the camera. Then you should click on the item “next”, after which a rectangular outline will appear on the display.
• Use the “up”, “right”, “down” and “left” keys to position the outline in the desired part of the screen.

The listed recommendations allow you to quickly restore the system and get rid of poor picture quality, blurring and other defects. The subsequent start of the system will lead to the appearance of yellow lines on the screen, which will greatly facilitate the parking process.