How to install a rear view camera on a KIA Rio hatchback (sedan) with your hands

Reversing in any vehicle creates a large number of problems. The Kia Rio rear-view camera, which is included in several trim levels, can simplify the task. From time to time, there is a problem associated with the improper operation of such a device. You can dismantle and repair the device with your own hands if you have a small set of tools.

Features of the original camera

The stock camera on the sedan and hatchback Rio 4 has properties that facilitate reversing. The rear view camera on the Kia Rio has the following qualities:

• The device provides more complete visual control in comparison with budget models.
• In some trim levels, a camera is installed that can display video in high definition resolution. At the same time, the picture quality is not lost in low light.
• The displayed image is equipped with parking markings. It facilitates reversing maneuvering in confined and tight urban environments.
• When equipping the camera, a wide-angle lens is used. Protection is provided when using a shock-resistant housing, which is protected from aggressive environmental influences.
• Some models can work in the infrared range, which is selected at night. Some webcams transmit information to a server where it can be stored for a long period.

The original camera can be installed by hand on the X-Line model. At the same time, the cost of the used equipment is low.

What to choose for replacement

If the original Kia Rio X-Line rear view camera is expensive, you can choose another model.

Most often, they pay attention to the Chinese versions, since they are much cheaper.

When installing the camera on a car without a corresponding option, you should consider the need to place a display on which the image will be displayed.

How to install and connect

Self-installation of the Kia Rio view camera does NOT create difficulties. To carry out the work, you need electrical tape, screwdrivers, a knife, clips and keys. Video camera installation can be divided into several main stages:

• The trim is removed, after which you need to pull out the cover. The panels are fastened with screws and caps. To increase reliability, locks are used, which just press a little.
• You can install the device instead of a plafond, which is designed to illuminate the room. This place is most suitable because it provides the required visibility and protection from environmental influences.
• If we install the device in a car, which was supplied without a camera, we have to lay a cable through the entire cabin to the torpedo. In most cases, the cable is laid along the floor under the finishing material or under the plastic protection of the threshold, but in some cases it is attached to the roof.
• After laying the wire, the device is connected to the reversing lamp, as well as to the main device. Such a scheme determines that the system will turn on only when reversing.
• At the time of connection to the GU, the tulip is connected to the CCD IN jack.
• The plug, located at the rear, consists of ground, side light, reversing fog light connectors. It is recommended to use a special clip-connector when connecting.
• If there is no OEM monitor, you should install an external one to which the video recording device will be connected. It is often placed over a mirror.
• After completing the procedure, you should check the operation of the system. For this, reverse gear is engaged. In some cases, it is necessary to adjust the position of the camera, since even a slight displacement becomes a prerequisite for which it is uncomfortable to use the system.

If there is a bolt near the device, then you should put a mass on it. Putting the original device in its original place is quite simple, but in some cases you have to change its shape and size.

Possible malfunctions and their elimination

Some versions of the vehicle come with an integrated rear view camera. Possible malfunctions of the system that allows you to safely maneuver in reverse are in the following points:

• Damaged wiring.
• The appearance of oxide on various contacts.
• Mechanical damage to the case.
• Malfunction of the device itself.

You can fix some problems yourself. A wiring damage case has the following features:

• The hardest part is finding the gap. It is not always possible to visually determine cable damage; a multimeter is required for continuity.
• After determining the location of the break, it is necessary to replace the entire cable, to save money, the section is cut off and both ends are connected, qualitatively insulated.

To determine the state of the device, you need to dismantle it. At the same time, we note the following points:

• Mechanical damage indicates moisture may have entered. Too high humidity becomes a prerequisite for the appearance of corrosion on the contacts.
• The connection pins are inside and outside the device. There are no problems with the restoration of external problems, it is difficult to gain access to the internal ones, since not all of the cameras in the model are collapsible.

If the camera is damaged, it has to be completely replaced. Before buying a new one, it is recommended to clean all available contacts, since the problem often lies in the appearance of corrosion.

Rear view camera Kia Rio sedan

For greater safety when driving in reverse, the best option. Display the “picture” of what is happening outside the driver’s line of sight on the console screen (main device, monitor). By connecting a rear view camera, you will get the desired result. High-quality optics, good resolution and excellent visibility (170 degrees. You can see almost everything that happens behind the car) is a guarantee of comfortable and safe driving. Connecting a rear view camera to the system does not require any special skills (power /. And video cable), the only difficulty. Carefully lay the line cable through the passenger compartment to the dashboard. The camera refers, as a rule, to the place of the license plate illumination, rather than disturbing the overall design. Increased dust and moisture protection guarantee long-term use of the system, during the entire service life of the vehicle (however, it is not recommended to direct a jet of water under pressure at the camera when washing a car). High light sensitivity makes it possible to use the camera in the dark.

Dust and moisture resistant.

This reversing camera is water and moisture resistant. It has an IP66 protection index.

Compatibility.

The camera has a built-in license plate light and is installed instead of it, without violating the overall design of the system.

Markup.

Switchable lane lines allow you to estimate the actual distance to an object without leaving your vehicle.

The camera’s viewing angle is 170 °, which is much more than the capabilities of human vision. You get a panoramic view.

All connecting cables and mounting accessories are included with the device. The high quality of Incar components are ready to be confirmed by hundreds of thousands of motorists using our equipment Not only, but also in Kazakhstan, Ukraine, Belarus and Moldova.

Clarifications on the body models and years of production Kia Rio (2011-2017) sedan.

Specifications

Sensor	1/3 “color CMOS
Resolution	480 TV lines
Number of pixels	628582
system	NTSC
viewing angle	170 degrees
Minimum illumination	0.1 LUX
waterproofness	IP66
video output	1Vp-p, 75Ohm, RCA male
operating voltage	12V DC
Working temperature	-40.65 degrees
parking lines	switchable markup

Specifications are subject to change without notice.

Kia Rio rear view camera

Modern electronic devices, which are constantly replenishing the list of equipment in the car, are designed to provide the driver and passengers with an appropriate level of comfort and safety. For example, not so long ago, parking sensors caused a real delight in the public, and now they are ordinary means that allow the owner of a car to park safely. Regularly acquires progressive electronic accessories and a practical Kia Rio model. Consider a rear view camera. For Kia Rio, it comes in two versions: standard and standard. The functionality of both classes of elements is identical, but the differences lie in how the rear view camera is installed.

What are the advantages of rear view devices?

For the Kia Rio model, a device such as a rear view camera is endowed with a number of advantages. Most owners, who have tested this accessory in action, unanimously reiterate that there are no negative sides in the video element.

The positive aspects of the device include the following:

• Exceptional aesthetics, because in comparison with the parking sensors, where the sensors are flush with the bumper, the rear view camera is absolutely invisible to the prying eye.
• Silence of action;
• The ability of the lens to broadcast a high definition image;
• Enviable viewing quality regardless of the time of day;
• The ability to implement a color picture on the display with the marked contours of the parking lines (the image appears immediately after activating the reverse gear of the transmission).

All types of cameras that fit the Kia Rio boast a wide angle in terms of visibility. This figure reaches 170 degrees. The lens of the device is enclosed in a durable case and has a parameter of 1.8 mm. This design allows you to protect the optical device from harmful penetration of moisture, dust and other pollutants. Equipment modifications are capable of realizing images with the following resolution:

• 628 x 582 dots;
• 704 x 576 pixels.

What complete set does the camera have and how to mount it?

As noted, there are two types of devices among the cameras available for the KIA Rio. The universal category of equipment will suit different models equally well, regardless of the generation of their origin. The standard device should be selected for a specific modification of the “Korean”. The first type must be installed in the tailgate (in the place under the license plate), and the second can be purchased in conjunction with a lamp designed to illuminate the rear number of a car.

The display may be included with the video element, but in most cases it is purchased separately. Manufacturers include a video cable in the mandatory kit for the element. Their length reaches six meters. The picture generated by the camera is to be transmitted to a special monitor, which is integrated into the salon rear-view mirror. Alternatively, the broadcast can be carried out on the display of the multimedia complex.

Setting up rear view video

The very installation of the rear view camera looks like this.

• First, dismantle the upholstery in the luggage compartment of the KIA Rio.
• Now we remove the rear lighting device, which serves to illuminate the stern license plate.
• The camera is immersed in the nest and fixed with a pre-prepared fastener.
• The next step will be to connect to the onboard power supply.
• The cord supplied with the camera contains a pair of connectors. The first one is connected directly to the device, and the second one is connected to the power cable of the rear headlight of the KIA Rio.
• After complete switching of the wiring, we proceed to install the room lighting lamp.
• The video cable should be pulled through to the points of the cabin where the display is supposed to be installed. Recommended wiring Place in the corrugated pipes originally present in the vehicle.
• Now we mount the screen itself.
• Upon completion of the entire list of operations, we check the functionality.
• If everything works, then I return to its place the previously dismantled upholstery of the luggage section.

Let’s sum up

When the installation of the rear view camera is carried out correctly, then when the reverse gear is activated, the corresponding picture appears on the monitor. Today, the role of the camera cannot be overestimated, especially for novice motorists, because the rear view camera is designed to provide irreplaceable assistance in maneuvering in tight spaces in the parking lot.

Installing a rear view camera Kia Rio. How to install a rear view camera on Kia Rio

Many car owners of Kia Rio are faced with a dilemma of what is best to install on their car. parktronic system or just a rear-view camera. It is quite difficult to give an unambiguous answer in the choice of specific parts for Kia Rio to this question, and even more difficult to advise from the outside. The choice is very subjective. However, we will try.

And first, let’s decide on its advantages and parameters.

• Provides a more complete visual control in comparison with budget models of the “parking assistant”.
• Unlike parking sensors, it looks much more aesthetically pleasing and fits better into the design of the car. In addition, it is less noticeable, as it is most often installed above the license plate, under the bend of the trunk. Sensors installed on the bumper, even painted to match the color of the car, do not always have an ergonomic look, and for their fastening, drills are often required.
• Certain lens models are capable of delivering high definition video, while working equally well both during the day and at night.
• Usually, the image is also equipped with parking markings, which act as a guide when maneuvering in reverse in closed and cramped urban environments.
• Rear-view cameras Equipped with a wide-angle lens built into shock-resistant housings, protected from aggressive environmental influences such as moisture, sand, dust or dirt.

If the choice still fell on the first option, then feel free to go to the page describing the installation of the parking sensors. If you decide that your Kia Rio is worthy of the “honorable wearing” of the second accessory, this article will help you understand the process of installing and connecting this miracle of technical thought.

In the text, we will consider the process of installing a rear-view camera, combined with a license plate, on the Kia Rio sedan model, and connecting it to the radio tape recorder. For a hatchback, the actions will be similar.

• Camera;
• Monitor for displaying images on the rear-view mirror (not in all trim levels) or separately;
• Connection wires.

You may need: screwdriver, electrical tape, knife, clips.

• First, you need to remove the trunk trim and pull out one of the shades. You can read how to do this in the article on replacing the license plate light bulb. In short, you need to find the screws that secure the upholstery and handle, and Unscrew them by pulling out the caps. And then, pressing the clips, Squeeze the cover out and disconnect from the connector.
• Now, in this place install the rear view camera.
• How to lay wires through the cabin, it is better to decide on your own: let them on the floor, hide them under plastic, or through the roof.
• The wiring connection is reduced to connecting the wires from the rear view camera kit to the head unit and the reversing light plug.

• In the GU, you need to connect the tulip to the CCD IN jack, and the red wire coming out of the tulip with the blue REVERSE cable (usually there is a label with the name on it).
• The rear plug consists of a mass, side lights, fog lights and reverse. It is more convenient to connect using a special clip-connector for 1mm. Connect the red wires from the tulip and the camera power supply to the plus, which is the orange-white power cable (on the far right in the photo). The black ground wire must be connected to the minus (black on the far left). In addition, if we observe the mounting bolt on the body (it is also relevant for the Kia Rio hatchback model), you can put a lot on it, leave the rest on white with an orange stripe.

Everything. The rear view camera connection process is now complete. It remains only to check its performance, and you can safely move forward.

Also, we advise you to watch a video explaining how to connect wires in Kia Rio.

What complete set does the camera have and how to mount it?

• The rear view video device has exceptional aesthetics. Unlike the parking sensors, the sensors of which are visible on the bumper, the lens is invisible to the prying eye. The equipment is completely silent.
• The lens produces images of high definition and excellent quality. Rear visibility is equally good at any time of the day.
• The equipment is capable of producing a color picture with parking markings. This combination will ensure safe reverse travel. The image appears on the monitor in automatic mode immediately after switching the lever to the reverse position.

Rear-view cameras designed for installation on the Kia Rio are of two types. Universal equipment is suitable for any model and generation, and the standard equipment is selected for a specific machine. The first type of rear-view camera is mounted in the tailgate of the Kia Rio above the license plate, the second comes complete with a lamp, which illuminates the rear number of the car.

The process of installing the camera itself is as follows. The very first step is to dismantle the trunk trim. Work should be done very carefully so as not to damage the material. After that, it is necessary to remove the lantern, which serves as a backlight for the number. Rear view camera for Kia Rio fits snugly into the socket and is fixed with brackets and screws.

A rear view camera will become an assistant and an experienced driver, and beginners who have just started to master the Kia Rio car in business.

For the Kia Rio model, a device such as a rear view camera is endowed with a number of advantages. Most owners, who have tested this accessory in action, unanimously reiterate that there are no negative sides in the video element.

The positive aspects of the device include the following:

• Exceptional aesthetics, because in comparison with the parking sensors, where the sensors are flush with the bumper, the rear view camera is absolutely invisible to the prying eye.
• Silence of action;
• The ability of the lens to broadcast a high definition image;
• Enviable viewing quality regardless of the time of day;
• The ability to implement a color picture on the display with the marked contours of the parking lines (the image appears immediately after activating the reverse gear of the transmission).

All types of cameras that fit the Kia Rio boast a wide angle in terms of visibility. This figure reaches 170 degrees. The lens of the device is enclosed in a durable case and has a parameter of 1.8 mm. This design allows you to protect the optical device from harmful penetration of moisture, dust and other pollutants. Equipment modifications are capable of realizing images with the following resolution:

• 628 x 582 dots;
• 704 x 576 pixels.

As noted, there are two types of devices among the cameras available for the KIA Rio. The universal category of equipment will suit different models equally well, regardless of the generation of their origin. The standard device should be selected for a specific modification of the “Korean”. The first type must be installed in the tailgate (in the place under the license plate), and the second can be purchased in conjunction with a lamp designed to illuminate the rear number of a car.

The display may be included with the video element, but in most cases it is purchased separately. Manufacturers include a video cable in the mandatory kit for the element. Their length reaches six meters. The picture generated by the camera is to be transmitted to a special monitor, which is integrated into the salon rear-view mirror. Alternatively, the broadcast can be carried out on the display of the multimedia complex.

The very installation of the rear view camera looks like this.

• First, dismantle the upholstery in the luggage compartment of the KIA Rio.
• Now we remove the rear lighting device, which serves to illuminate the stern license plate.
• The camera is immersed in the nest and fixed with a pre-prepared fastener.
• The next step will be to connect to the onboard power supply.
• The cord supplied with the camera contains a pair of connectors. The first one is connected directly to the device, and the second one is connected to the power cable of the rear headlight of the KIA Rio.
• After complete switching of the wiring, we proceed to install the room lighting lamp.
• The video cable should be pulled to the points of the cabin where the display is supposed to be installed. Recommended wiring Place in the corrugated tubes originally present in the vehicle.
• Now we mount the screen itself.
• Upon completion of the entire list of operations, we check the functionality.
• If everything works, then I return to its place the previously dismantled upholstery of the luggage section.

Installing a rear view camera on a Ford Focus 3 hatchback or sedan (station wagon)

• Standard camera
• Analogs
• How to install and connect
• Malfunctions and repairs

You can significantly expand the capabilities of Ford by installing a new main unit. It can serve as a navigator or TV. Rear view camera Ford Focus 3 further expands the capabilities of the device, you can also install it yourself. If the basic recommendations are followed, the probability of making a mistake is reduced.

Standard camera

Rear-view camera Ford Focus 3 Sedan or Station wagon is installed at the factory exclusively in an expensive configuration along with a standard parking sensor. The features of the original product are as follows:

• There is a dedicated Seat in the luggage compartment lid.
• Wiring has been laid through the cabin, for which a special niche is created.
• The workmanship of the device is high.
• In most cases, the device applies a virtual floor markup to the image.

Rearview camera Ford 3 Restyling can display virtual markings that adapt to the prevailing circumstances. The features of self-installation largely depend on the type of device to which the information will be displayed.

Analogs

Cameras can be called the most common device that is installed in various equipment.

New cars are supplied immediately with several devices, the image from which, when processed, creates a three-dimensional view.

On budget models of cars, only one camera is installed, which turns on when reversing. When choosing an analogue, attention is paid to the following points:

• Viewing angle.
• Type of material used in the manufacture of the case.
• Enclosure protection class.
• Resolution.
• Night shooting mode.
• Case dimensions.
• Type of used plug for wiring.
• Voltage.

Rear view camera for Ford 3 Hatchback is manufactured by many companies. When choosing a model, you need to take into account the popularity of the brand, since some Chinese manufacturers reduce the cost by using low-quality materials.

How to install and connect

Installation of a camera on a Ford can be done independently. In this case, a combination of a Chinese main unit and a camera will be used. Both can be purchased on the Chinese website at a low price. Recommendations for completing the work are as follows:

• Before installing the device, it is recommended to pre-connect it. Due to this, device compatibility is checked.
• It is recommended to start direct installation by removing the tailgate trim. To do this, remove the lower center pad, you need to pull it a little. Do not apply a load abruptly, as this may damage the panel.
• There are two bolts under the handle covers. Their dismantling is carried out using a Phillips screwdriver.
• After removing all panels, access to the wiring in the rear is available. The cover is removed by unscrewing 6 nuts, the last resistance is created by 3 pistons.
• There is a rubber plug for wiring in the door device. It is also used for laying wires; it is possible to simplify broaching by using a wire and a special liquid.
• After installing the camera, it is recommended to fill it with sealant. This allows you to significantly extend the operating life of the device. High humidity becomes a prerequisite for the appearance of corrosion and malfunction of microcircuits.
• If the camera is installed correctly, wiring should be done. Power is taken from the right lamp, a green-brown wire is used for this.
• The cabling is being laid. For this, the casing is removed, which is attached when using clips. For standard wiring, there is a special corrugation along which the cable from the camera is pulled. It is recommended to pull the wiring with clamps, which will increase the reliability of the created system.
• It is difficult to pull the wiring to the front torpedo, it takes a long time. The plug is inserted into the corresponding socket, then the operation is checked. If a mistake was made at the time of laying the cable, then there is a possibility of signal loss.

The price of the issue, taking into account the use of consumables, is about 1600 rubles. It is necessary to provide for the possibility of installing a washer, which will significantly increase the efficiency of the entire system. The device is checked by placing the vehicle in a parking space.

Malfunctions and repairs

Common malfunctions include the following:

• Mechanical damage to the camera.
• Cable break.
• Corrosion on contacts.
• Offsetting the device in place.

It is almost impossible to repair the camera with your own hands, since the design is represented by a combination of small microcircuits. It is possible to check a cable break only when using a tester; corrosion on the contacts is revealed by visual inspection. The problem arises with the fact that you have to dismantle the skin, which takes a lot of time.

Installing a rear view camera on a Kia Rio with your own hands

Modern automotive equipment ensures the safety of the driver and passengers of the car. If you buy a rear view camera on a Kia Rio hatchback or sedan, there is a chance of eliminating some risks. How to choose and install a device.

Camera features

The device can be universal and designed for any car. The stock camera for Kia Rio was created taking into account the features of the model. The differences between the two proposals are only in the installation activities.

• Decent aesthetics. The lens is invisible to people around, has a beautiful design;
• A clear and high-quality image is guaranteed. The overview will be sufficient at any time of the day;
• Transmission of a color picture with parking markings is provided. In this case, tuning is performed with maximum success;
• Large viewing angle up to 170 degrees. This is one of the main benefits. The lens features a 1.8mm lens and a high-strength body. The case guarantees protection from external factors: dust, moisture, dirt;
• Output of images with a resolution of 628×582 and 704×576 pixels.

Features of the device configuration

The main division has already become clear: standard and universal devices. Perfect option. OEM camera, as it is designed for a specific car.

The universal model must be installed in the Rio’s tailgate above the license plate. Standard equipment is included and integrated into the tail light.

The monitor for broadcasting the image is supplied separately, so it is advisable to take care of its purchase. Along with the lens, cables for video transmission are sold with a length of about six meters.

Correct installation and adjustment allows you to easily observe what is happening outside the car on the roadway.

The picture from the device is transmitted to the monitor, which is customary to mount on a mirror or radio screen.

State-of-the-art rear view camera for the Kia Rio included as standard. one of the best deals for every motorist.

Features of device mounting

The luggage compartment trim is initially removed. Work should be done as carefully as possible, as otherwise there is a risk of damage to the material. Then they remove the license plate light. The reversing camera fits neatly and tightly into the socket and is secured with brackets and screws.

Next stage. connection of wiring. The package traditionally includes a cord with two connectors. One of them connects the camera and the other. rear light power.

After connecting the wiring, the Kia Rio will work, but remember to put the license plate back on before driving. To broadcast on the monitor, the video cable is pulled to the place of the screen.

Summary

Installation of the monitor and installation of the rear view camera. the basis for a successful and safe driving Kia Rio.