How to install and connect a rear view camera on a Hyundai Solaris sedan or hatchback to a regular place

Not all Korean cars are equipped with a standard parking video device. However, it is possible to mount it yourself. A rear-view camera is installed on the Hyundai Solaris sedan in a regular place located on the trunk lid instead of one of the license plate lights.

Functions and features of the standard

The standard video camera for Hyundai Solaris is a cap made in the form of a lamp with built-in optics. It is placed instead of any flashlight. It is not difficult to install it, because the fixing and wiring are made in full agreement with the device being replaced. However, many drivers do NOT recommend this. There are several points that affect this decision.

When installing a Hyundai Solaris rear-view camera, 1 room lamp remains in operation. If it fails, then the license plate will not be highlighted, and this is an excuse for stopping the vehicle by the traffic police inspectors. Due to the fact that the lamps are installed away from the trunk lid axis, the image will be displaced to one side or the other, depending on the placement of the device, which negatively affects the quality of parking in drivers with little driving experience. This fully applies to the installation of a rear view camera Solaris hatchback.

What can replace the original

Instead of the standard Hyundai Solaris rear view device, many motorists use a universal video camera. In order not to rip it off, use an internal fastening on a hairpin. This slightly increases the work time, but the result is worth it. Position it so that the screen displays a SYMMETRICAL image of the traffic situation behind the car. The protrusion above the license plate (“saber”) protects the lens of the video device from dirt and precipitation, and both license plate lamps remain in operation.

The equipment connection is NOT different from that of a standard device. Another location of the rear view camera Hyundai Solaris leads to its premature failure due to moisture ingress inside the case and damage to the optics.

How to install and connect

Installation of a standard device does NOT cause any difficulties, since To do this, you need to dismantle 1 lamp and install the camera in its place. It is fastened with 2 self-tapping screws at the same points as the lamp. Connection to the vehicle’s on-board network (12 V) is carried out from the right block of aft lights. The reversing lamp is located here. The negative wire is connected to the housing terminal of the license plate lighting devices.

Mounting a universal video device instead of a standard Hyundai Solaris rear view camera requires a mounting hole. On the body of the device there is a threaded rod with a nut for fastening. The camera is designed in such a way that when placed on a flat surface, the lens is directed at an angle of 10-15 ° downward. This makes it possible to better navigate the road situation and correctly determine the distance to the obstacle.

The wires are pulled into the trunk through a standard hole with a rubber plug. Due to the fact that the plastic elements of the cabin are difficult to dismantle, the line is laid under the roof sheathing. To do this, remove the door seal and push the cable under the roof. If a monitor in a mirror is used as a screen, then the wires are pulled from above through the seal of the interior lighting shade. When connecting the display of the standard head unit, the line is drawn under the windshield pillar trim down.

The camera plug is inserted into the corresponding jack on the back of the recorder. When installing parking sensors on a car, the wires from both devices are connected into 1 bundle and pulled together. It is better to carry out these installation work at the same time, so as not to remove the cladding elements once again.

If the driver has correctly set and connected the video system, then when the reverse gear is turned on, an image of the situation behind the car will appear on the screen, and the colored signal lines will show the distance to the obstacle.

On Hyundai Solaris, the installation of a camera for viewing and reviewing the traffic situation when parking will cost within 1,100-1,300 rubles and will not greatly affect the family budget. The presence of THESE devices makes parking the car easy and safe.

Malfunctions and repairs

The performance of the camcorder depends on the operating conditions and the quality of installation. In some cases, jolting and vibration can fray the carelessly routed wires. Then the tourniquet will have to be dismantled and inspected and searched for the location of insulation damage. This can be avoided by routing the wires into the corrugated hose.

During operation of the device, moisture can get inside the case due to a violation of its tightness. The stock camera has a removable back cover. The body is disassembled, and the elements are blown with air and dried. The universal video device can be disassembled, although it is covered with sealant. The steps to restore functionality are similar. It is better if these works are performed by a specialist.

Rear View Camera Hyundai Solaris

For greater safety when driving in reverse, the best option. Display the “picture” of what is happening outside the driver’s line of sight on the console screen (main device, monitor). By connecting a rear view camera, you will get the desired result. High-quality optics, good resolution and excellent visibility (170 degrees. You can see almost everything that happens behind the car) is a guarantee of comfortable and safe driving. Connecting a rear view camera to the system does not require any special skills (power /. And video cable), the only difficulty. Carefully lay the line cable through the passenger compartment to the dashboard. The camera refers, as a rule, to the place of the license plate illumination, rather than disturbing the overall design. Increased dust and moisture protection guarantee long-term use of the system, during the entire service life of the vehicle (however, it is not recommended to direct a jet of water under pressure at the camera when washing a car). High light sensitivity makes it possible to use the camera in the dark.

Dust and moisture resistant.

This reversing camera is water and moisture resistant. It has an IP66 protection index.

Compatibility.

The camera has a built-in license plate light and is installed instead of it, without violating the overall design of the system.

Markup.

Switchable lane lines allow you to estimate the actual distance to an object without leaving your vehicle.

The camera’s viewing angle is 170 °, which is much more than the capabilities of human vision. You get a panoramic view.

All connecting cables and mounting accessories are included with the device. The high quality of Incar components are ready to be confirmed by hundreds of thousands of motorists using our equipment Not only, but also in Kazakhstan, Ukraine, Belarus and Moldova.

Clarifications on the bodies of models and years of production Hyundai Solaris (2010-2013), Verna (2010-2013).

Specifications

Sensor	1/3 “color CMOS
Resolution	480 TV lines
Number of pixels	628582
system	NTSC
viewing angle	170 degrees
Minimum illumination	0.1 LUX
waterproofness	IP66
video output	1Vp-p, 75Ohm, RCA male
operating voltage	12V DC
Working temperature	-40.65 degrees
parking lines	switchable markup

Specifications are subject to change without notice.

Installing a rear view camera on Solaris. quickly and effortlessly

So, the rear view camera on Solaris consists of two parts:

• A camera that is installed above the car number or trunk lid.
• Monitor, it is installed on the control panel.

The two parts are connected with special four-core cables. The first two wires are connected to the reversing lamp. The rest of the veins are led to the monitor through the car interior trim.

At first glance, it may seem that installation and installation is a very difficult process, but in reality it is not. If you adhere to all the installation rules, there will be no big problems. Installation should be done very carefully and carefully so as not to damage your car.

Consider installing a rear view camera on car brands: sedan, Hyundai, Hyundai solaris. These cars have a similar fastening of the cladding, so the installation is almost the same in each case.

Tools needed for work:

• Set of screwdrivers.
• 10 spanner.
• Insulating tape.
• Corrugation.

We start installing the rear view camera on the Solaris:

• First you need to disassemble the trunk handle. It is held on self-tapping screws. Unscrew it carefully with a Phillips screwdriver. After that, we remove the clips, there should be NO more than 10 pcs.
• In total, you should get a bare body. Remove the trunk lining. This is both the part where the LEDs and the number are. The boot lid is held in place by bolts and clips. It is important, first you need to unscrew the bolts and nuts, and then the clips.
• After removing the cover, you need to drill a special plug in it. It is located approximately in the middle, above the license plate.
• In order for everything to be neat, it is recommended to begin with pulling out the plug and drilling a 2 mm hole in it. The camera should fit very tightly into this hole.
• You also need to drill a hole in the removable boot lid. Drill first with a thin drill, and then the desired thickness.
• Before attaching the camera to the front, there are a few things to consider. The camera should be positioned at a certain angle downward. This is necessary so that you can calculate approximately the distance to the interference.
• After installing the camera, a small gap remains between the trunk lid and the body. It needs to be filled with colorless sealants.
• After drying, Install the trunk lid in its place.
• We connect the four-core cable to the camera and extend it to the monitor. This can be done in two ways. Through roof or floor upholstery.
• We remove the ceiling sheathing, it is mounted on self-tapping screws and special grooves. We pass the cable through the top and connect, we lived to the monitor. If no abnormal situations occurred when switching on. Installing the roof sheathing back.
• First you need to fix it in the grooves, and then tighten the screws.
• After turning on the camera on the screen, it should be visible, all the angle of the rear of the car.