How to install and connect a rear view camera on a Chevrolet Cruze sedan (hatchback)
When reversing, a reversing camera is required, which displays the image on the center display. Despite the fact that the Hatchback is small, such a device would be useful. Installation of the rear view camera for Chevrolet Cruze sedan can be done by yourself, it requires a small set of tools.
Reversing camera installed to a Chevrolet cruze
Established
The car in question is supplied in a configuration that provides for the presence of such an option. The stock camera of the Chevrolet Cruze hatchback has the following features:
- Large viewing angle. The installed camera has an indicator of 170 degrees. Therefore, when reversing, the required visibility is provided.
- The device displays the markup. It greatly simplifies the parking of a vehicle.
- Decent image quality in low light. The camera is not equipped with a backlight, but it turns on in reverse gear along with the flashlight.
- A standard device can last for several years. This is due to the fact that it has a plastic sealed body.
- The cost of the original camera is high. You can significantly reduce costs when purchasing a device with disassembly.
The device is highly protected against environmental influences. In some cases, a camera is purchased for the plafond, which is used as a protective element.
Analogs
If desired, you can install analogs. When making a choice, you should pay attention to the following points:
- Chinese sites sell a wide variety of devices. They can be much cheaper while still displaying a high-quality image.
- When choosing a camera, attention is paid to the size of the display. At low resolution, the picture will be very blurry, the lack of clarity will create a problem at the time of parking.
- The rendered markup can be static or dynamic. The second option is considered more practical, as it changes depending on the position of the vehicle.
When choosing analogs, it is recommended to take into account the size of the structure. If the device is larger, then you have to increase the size of the footprint.
How to install
You can install the device yourself. This requires the following tools and consumables:
- A special device designed to dismantle decorative caps. In their manufacture, plastic is used, which will not be able to withstand a high load. Can be replaced with a flat head screwdriver.
- A set of keys is required. To disassemble the rear door and the shade, you will have to unscrew a lot of fasteners.
- A multimeter is required to test circuits. If there was already a system earlier, then the old wiring needs to be checked. Minor damage and corrosion on the contacts leads to a large number of problems: no signal, flashing, and others.
- Phillips and flat blade screwdriver.
- Closed relay.
- Suitable type of wiring. It is selected depending on which camera is used.
- Insulating tape. This material is often used as insulation.
- Fuse. Experts recommend installing a safety element that will eliminate the possibility of a short circuit.
During the installation process, you may need a rag to clean dirt and a knife to strip the insulation. If an old camera is installed that needs to be dismantled, then forceps are used.
Camera installation can be divided into several basic steps. They look like this:
- Installation of the camera provides for installation in a special seat in which the room lighting is located. This location works well as it provides the required viewing angle.
- To gain access to the required place, you need to remove the skin. It is attached using several screws and clips. Dismantling is easy enough, but you should be careful, as strong pressure can damage the fasteners.
- When laying the loops, care must be taken to ensure that no water gets into the area where they are located. Too high humidity can cause oxide to form on the contacts.
- The plafond is being dismantled, which serves to illuminate the room. It is secured with several bolts. At the time of disassembling the structure, it is recommended to clean it from various contaminants.
- The device wires lead to the front of the car. For this, a special hole with a rubber gasket is used. When laying the cable, attention should be paid to ensure that there is high-quality insulation at the point of contact with the case. Vibration can rub the insulation. You can eliminate the likelihood of such a problem when using corrugation.
When attaching the camera, care should be taken to secure the device securely. Attention is also paid to the degree of tightness, since moisture ingress causes corrosion.
How to connect
You can connect the device yourself. For this, the cable is laid through the cabin. You can connect a view camera as follows:
- The cable is being laid under the sheathing. She acts as additional protection. In most cases, the wires are placed under the sill trims.
- When connecting, special adapters are used. They eliminate the likelihood of signal loss due to strong vibration, allow you to quickly dismantle the main elements of the system.
- The positive lead is connected to the positive lead of the rear-view headlight. Likewise, simultaneous activation of the rear view camera with reverse gear can be ensured.
- It is recommended to fasten the wiring using clamps. Otherwise, there is a possibility of rubbing the wire on metal parts of the body.
- The wire from the camera can connect to the rearview mirror, head multimedia system, separate screen and other display devices.
If we connect the rear view camera to the old wiring, all contacts should be stripped. Low resistance can lead to overheating of the cable and loss of signal. After completing the work, you should test the system, as there is a possibility that the camera is not positioned correctly. Even a slight offset can reduce the efficiency of the entire system.
Connecting a reversing camera to a Pioneer radio
Now we will specifically talk about how to set up and connect the reversing camera to the Pioneer radio tape recorder. There are small nuances here that mislead everyone. We connect the camera to the reversing light, all the power is on the camera, then the wire through which the video signal will go. In the pioneer, this is a brown tulip not to be confused with yellow. We go into the settings, find the section in the rear view camera menu, put the item on, and switch the polarity to battery mode.
Our camera works, you can check this by going to the main menu and select the camera icon, but it will not turn on automatically. This can be corrected by connecting the purple wire to the taillight (where the camera is). As a result, when the reverse gear is turned on, the lamp lights up, the camera is powered, and the radio tape recorder understands that it is necessary to switch to reverse gear.
The whole connection diagram of a rear–view camera is quite simple, and therefore most drivers often cope with its installation on their own. In cars equipped with automatic transmission, accidental activation of the rear view camera may occur.
To eliminate this trouble, you need to install an additional sensor for the delay in turning on the camera. In each car model, the installation of the camera may be different, but in the details, the principles of connection are similar. The connection process is more complicated for video cameras that transmit a signal via radio communication, but they have the advantage that several such cameras can be connected. There are more and more cars on the streets of the city, so a rear view camera is already a necessity. It will not only help you park correctly, but will also preserve evidence of your innocence in the event of a collision.
Often, a reversing camera is installed after purchasing a new radio tape recorder, for this case we have an article “how to connect a radio tape recorder” in it you will learn about adapters, adapter frames and much more.
How to install parking sensors on a Chevrolet Cruze and connect a rear view camera
How to install and connect
The main elements of the system under consideration are located in the bumper and luggage compartment. To carry out the work you will need:
- Drill with various attachments.
- Measuring instruments.
- Multimeter.
- Molar tape.
- Knife.
- Parktronic kit with additional wires.
Work should begin with dismantling the bumper. Due to this, the task of creating mounting holes for ultrasonic sensors is greatly simplified. The instructions for performing the work are as follows:
- After removing the bumper, a molar tape is glued to the front side.
- With the help of a pencil and measuring instruments, the surface is marked, the future position of the sensors used is determined.
- Holes are created with a drill with a special nozzle. When working, you need to be careful, the holes should be located strictly perpendicular to the surface.
- The molar tape is removed, the edges of the holes are processed.
- The sensors used are installed in their places. In some cases, you have to press a little on them.
- If the holes created do not require rework, the edge is covered with glue, the wires sink, and the sensor is deepened into the bumper structure. At this stage, you need to follow the strict horizontal arrangement.
- There is a suitable place for the parking assist control unit in the luggage compartment. After that, the cable from the sensors is laid to the device itself.
- Special attention is paid to ensuring that the wiring has good insulation in the area of contact with metal and other edges. Even the slightest vibration can rub the insulation.
- All elements are connected. It is recommended to use special adapters for connection, since after soldering it will be difficult to dismantle individual elements.
Established
The car in question is supplied in a configuration that provides for the presence of such an option. The stock camera of the Chevrolet Cruze hatchback has the following features:
- Large viewing angle. The installed camera has an indicator of 170 degrees. Therefore, when reversing, the required visibility is provided.
- The device displays the markup. It greatly simplifies the parking of a vehicle.
- Decent image quality in low light. The camera is not equipped with a backlight, but it turns on in reverse gear along with the flashlight.
- A standard device can last for several years. This is due to the fact that it has a plastic sealed body.
- The cost of the original camera is high. You can significantly reduce costs when purchasing a device with disassembly.
The device is highly protected against environmental influences. In some cases, a camera is purchased for the plafond, which is used as a protective element.
How to install parking sensors on a Chevrolet Cruze and connect a rear view camera
Parking systems greatly simplify the procedure for placing a vehicle in a parking space. They are often included in the basic configuration of various vehicles, including the Chevrolet Cruze. You can replace the Chevrolet Cruze parking sensors or install a new one yourself; this requires a small amount of tools and consumables. A correctly positioned sensor will be able to determine the approach to obstacles of various types.
How to choose a camera
The modern electronics market, and especially China, is overflowing with a variety of cameras, and this makes the choice of the right thing more complicated. In order to make your job easier, decide on your priorities, which worries you more. price or quality. Not everyone needs high definition cameras, or cameras that can show even in low light. For some drivers, an inexpensive rear-view camera for a radio tape recorder is enough.
- In what resolution the camera writes, the higher the video resolution, the better the recording quality. And high definition of the image is not always needed.
- The next point is the sensitivity of the camera to lighting. In cheaper models, recording quality in low light can be very poor. Therefore, if, due to circumstances, you often use the car at night, then you should pay attention to this moment.
- If you have already decided where to put the rear view camera before buying, then you need to pay attention to the installation method of this particular model.
The procedure and diagram for connecting a rear view camera
And now in more detail about how to install and connect the rear view camera to the Pioneer radio. Why this model, because it is the most common. If we take into account the insecurity of our video camera, and the best view, then its place should still be above the number, outside.
It should be installed closer to the edge to improve visibility, but not so that it stands out. The installation of the camera itself does not represent anything complicated. The camera has a bracket required for installation, you only need to drill a couple of holes for the mounting bolts, and one hole for the cable.
And then the rear-view camera is included in the general electrical network of the car. If you are not strong in electrics, then it is better to turn to car service specialists, but if you have at least basic knowledge, then you can quite figure it out on your own. So, the order of connection is in stages:
- Any camera has two wires, one for transmitting the video signal from the camera to the monitor, and the other for power. Since the camera itself has short wires, you will need to build them up so that they are enough from the front panel to the end of the trunk (as a rule, an extension cable for the video signal is included in the kit).
- Where can I get power for the camcorder? Usually the camera is connected to the rear lights. Therefore, immediately after turning on the reverse, the rear view camera is also turned on.
- All wires that are pulled through the cabin and in the trunk must be secured and hidden. This will help to avoid unexpected network interruptions while driving.
- If you use a monitor instead of a radio, you will need to find a power source for it. If you have a Pioneer multimedia recorder, this issue is automatically resolved for you.
Rear view camera connection
Whether or not to install a reversing camera is up to each driver himself. In this article, we will tell you how to connect a rear view camera, and it’s up to you whether you need it or not. Connecting a rear view camera requires some knowledge and skills, so not everyone will be able to do it on their own. But if you nevertheless decide that the installation of a regular rear view camera is necessary for you, then use the tips from this article. With a small set of tools and the initial skills to work, take off, you can easily figure out how to connect a rear view camera.
Side mirrors, and your head turned 180 ° will not give the desired effect, some little things, or maybe not little things, you may not notice. And then the showdown with the owner of the scratched car may begin, and this can cost you tens of times more than connecting a reversing camera. Further in the article, we will consider which camera you can choose, whether a Chinese manufacturer is right for you, or if you prefer something more solid. We will also discuss whether it is possible to install a rear view camera with your own hands, and how to properly connect the device you have chosen.
Rear View Camera for Chevrolet
Pandora released a new Bluetooth dongle Pandora D-030 in April 2018. The main advantages of this product are size, power consumption and security. Pandora D-030. this is an ergonomic solution for everyone who is accustomed to the functionality of the key fob, but needs a more modest size and versatility.
BARBUS sells and installs video assistance systems for parking, consisting of front / rear view cameras and a monitor.
The rear view camera starts working when the reverse gear is engaged. The image can be displayed both on a standard monitor (if technically possible), and on a monitor installed additionally.
Camcorders installed instead of a license plate light are the most popular among our customers. They are made on a modern CCD matrix and fully retain their functionality as a license plate illuminator.
This section presents rear view cameras that are installed in a regular place for Chevrolet cars. (Chevrolet Cruze. Chevrolet Lacetti. Chevrolet Lanos, Chevrolet Cobalt, Chevrolet Captiva, Chevrolet Spark, Chevrolet Aveo, etc.)
You can find out about the availability of a video camera for your car in the warehouse by calling: 988-54-91. We will be happy to answer all your questions.
If you did not find your car in the list, this does not mean that we do not have a video camera for it. Perhaps we just did not have time to add it yet, or the video camera fits from another car model.
There is a positive experience of connecting video cameras to standard head units. This, unfortunately, does not yet apply to all car models. Call, specify. The cost of a video camera with installation in this case will be determined locally.
Rear view camera for Chevrolet cars
| Chevrolet cruze | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet Cruze station wagon | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet Cruze hatchback | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet aveo | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet lacetti | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet Lacetti hatchback | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet lanos | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet orlando | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet cobalt | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet rezzo | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet spark | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet HHR | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet captiva | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet aveo | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet lova | With installation 4500 r. | Without installation 2350 rub. | |||
| Chevrolet epica | With installation 4500 r. | Without installation 2350 rub. | |||
A video camera or monitor can be purchased separately from each other, if, for example, some piece of equipment is already installed in your car. There are also ready-made kits:
We offer rear view cameras, which are installed in a regular place, for cars of various brands and models (the list is constantly updated):
The BARBUS company provides services for the installation of alarms, immobilizers, mechanical protection and audio equipment on any cars of domestic and foreign production and has been operating since 1999.
CarNaviPlayer Chevy Cruze Radio Backup Camera Install
The Price List contains some of the most common models of car alarms and immobilizers. We are constantly testing new models that appear on the market and try to offer our customers the most break-resistant and reliable systems.
Our company is engaged not only in the installation of anti-theft equipment, but also its post-warranty repair, in particular AUTOSIGNALIZATION REPAIR, regardless of where and by whom the security complex was installed.
If you are experiencing known difficulties when parking your car in a cramped yard, we can offer video devices that will greatly facilitate this process. Pay attention to the Rear View Camera with Monitor
Payment is possible both in cash and by bank transfer. Bank cards are accepted.
All information on the site is for reference only and is not a public offer determined by the provisions of Article 437 of the Civil Code of the Russian Federation.
Installing a rear view camera on a Chevrolet Niva
You can install the system yourself; a Chevrolet Niva rear view camera, this requires a small amount of tools. How to choose another On Chinese Internet sites there are a large number of rear-view cameras that can be installed on the car in question. When choosing, the following points are taken into account: Dimensions of the device. If the car has a seat, then the camera is selected for. The protection of the case can be different. It is recommended to give preference to models that are protected from dust and moisture.
Self-installation of a rear view camera on a Chevrolet Niva
In order to be able to use the camera on the Niva at night, infrared illumination is mounted in it. In addition, this option significantly increases the cost of Chevrolet. You can install the system yourself; this requires a small number of tools. How to choose another On Chinese Internet sites there are a large number of rear-view cameras that can be installed on the car in question. When choosing, the following points are taken into account: Dimensions of the device.
If there is a seat on the rear view camera for Chevrolet, then the camera is selected for.
The protection of the case can be different. It is recommended to give preference to models that are protected from dust and moisture. The operating instructions indicate the temperature regime at which operation is possible. At the time of movement in the summer, the surface heats up to high temperatures.
Image quality and resolution. If the latest rear view camera for Chevrolet is small, it will be difficult to distinguish objects in the image. The presence of additional functions related to IR illumination, displaying virtual markings, and some.
Self-installation of a rear view camera on a Chevrolet Niva
At the time of parking, a lot of problems can be avoided by installing a rear view camera. Its purpose is to display the image on the salon display. The Niva Chevrolet rear view camera is extremely rare, since the car is not supplied with such an option. Do-it-yourself installation of the system can be called the solution to the problem.
How to install and connect
Installation of the camera on the Niva can be carried out independently.
Before carrying out the work directly, you need to decide where the device will be located: in the bumper, license plate, luggage compartment lid.
In most cases, they are placed in the luggage compartment lid, since its height is the most optimal. The instructions for carrying out the work are as follows:
- The wire is routed from the camera from the back of the car to the front. If it is installed in the bumper, then it is necessary to provide for high-quality insulation of the device. It is recommended to place the interconnect wiring away from the power cable, as otherwise noise may appear.
- The device is connected to side lights or a reversing lamp. This ensures that the device automatically engages when selecting reverse gear. It is recommended to insulate the connection point with the use of sealant and other materials, since moisture causes corrosion and a decrease in conductivity.
- When connecting, you need to pay attention to the quality of the connection of individual elements. The use of special plugs increases the reliability of the entire system.
To place the rear-view camera in the trunk lid, the lighting shade is dismantled. If the device is placed in the bumper, you will have to make a suitable hole. The system delivery set may include a rear-view mirror, which is located in the passenger compartment. Dismantling of standard equipment is carried out independently, it is attached with just a few elements.
Articles, Schemes, References
Mirror and rear view camera on Chevrolet Niva
I have empirically solved these three questions. If you are interested, read on, and if not, then just look at the photo.
These 1. D Having opened the trunk lid, I began to inspect, intuitively it seemed logical to me to remove the plastic trim on the wall where the hinge is. To remove this overlay, you need to lift the plastic pallets.
The pallets are fixed to the floor by 4 bolts, each pallet is 2 bolts, one bolt in each compartment. But before that, I still pulled out the launch and put it in the salon, at that moment it seemed to me that it would interfere with this whole procedure. The pallets can be locked in the raised position. If there is a plastic mat, it is better to pull it out, it will rest against the rear pillars and prevent the shelf from rising high.
You should get the same condition as in the photo below. Disassemble to such a state You see two large holes in the metal. Under the left one there is a rubber seal, and on the right there is a rear view camera for such a Chevrolet. Wire Inlet Wire Inlet I was lucky that the rearview camera for the Chevrolet was able to remove the left license plate light prior to this stage. To remove it, you need to slip a flat screwdriver from its right end and press the plastic retainer on the lamp.
The left lamp for illumination of the numbers The left lamp for illumination of the numbers The left lamp of illumination of the numbers Having pulled the wires from the sealed lead-in I found out that a part goes to this lamp a rear-view camera for Chevrolet. The display can be a special multimedia device, or a mirror in which the display is built. The second option is best suited because the driver sees everything that happens in his usual place, and it also helps to save the available cabin space.
Mirror and rear view camera on Chevrolet Niva
I calculated it using a test light. So, we cut into this wiring using the “guillotine”, in the second part we insert the wire from the sleeve with a fuse, I used a 5A fuse. Rear view camera for Chevrolet, connect the second end of the wire from the sleeve to the terminal block with 3-pin clamps, and to the remaining 2 contacts the terminal block, we connect the positive wires from the camera and the monitor, which were brought out before.
We put the entire structure inside the gray box and close it. This is done with the connection.!
Niva: Reversing Camera. Chevrolet Repair and Tuning
For example, the high-resolution video device can even be used as a traffic recorder. True, he will only record what is happening behind the car.
You should also pay attention to the angle of view of the camera.
How to install and connect Installing the camera on the Niva can be done independently. Before directly carrying out the work, you need to decide where the device will be located: In most cases, it is placed in the luggage compartment lid.
The instructions for carrying out the work are as follows: The wire is laid from the camera from the back of the car to the front. If it is installed in the bumper, then it is necessary to provide for high-quality insulation of the device. It is recommended to place the interunit wiring away from the camera powerplant on a Chevrolet field. The device is connected to side lights or a reversing lamp. This ensures that the device automatically engages when selecting reverse gear.
Pros The main advantages of installing this device are: You can see everything that happens behind the car Has the correct location of all objects, the left object is the installation of the camera on the Chevrolet field on the left, right on the right side The viewing angle is not less than degrees Can work all day Versatility in connection Installation The first thing is that must be done before installation, this will be determined with the place where the camera will be installed, for example, rear bumper, license plate or trunk lid.
Mirror. display. I don’t know the exact resolution, but the pixels are not big, a typical Chinese display.
Size. 5 ″. There is a Russian language, settings for brightness, contrast, saturation. The picture quality is practically not affected. There is a choice of aspect ratio, 16×9, and 4×3.
In 16×9 format, the picture is artificially expanded, all 5 ″ displays are used, but the picture is distorted and objects become wider than in real life. I chose 4×3, which does not involve the entire display, but only 4.3 ″, while the rest of the display is not backlit, and it seems that the display size is exactly 4.3 ″.
In this case, objects are reflected in real proportions. In bright sunlight, the image remains readable, but very faint, yet there is a mirror coating on top that reflects the light. But take a closer look. In normal daylight, in clear or cloudy weather, the display performs its functions with a bang.