Resetting the Toner Toner Brother Printer Toner

Carry out discharge only if you are sure that the cartridge with a toner is empty. If you have a toner, you will have to refuel it or buy a new full cartridge, since other parts of the printer can fail if the toner container is empty.

There is also no need to discard the counter if the message “not enough toner” appears on the screen “. In this situation, you can still print, but start writing when the toner in the printer will end and the container will be close to zero.

Why is the counter to be reset

Cleaning is a procedure for changing equipment settings. The protection itself is based on the following principle:

  • The manufacturer sets a special counter in the system;
  • During print, the chip calculates the number of sheets used, and when the cartridge capacity is exhausted, it signals this to the user, blocking the device.

Each cartridge has its own capacity. In some of them, the toner capacity is 2500 sheets, in others. 1000 sheets. The system is programmed depending on the number of sheets. If the print limit exceeds the message “Replace the consumables”, “no toner” or just a blinking indicator. Even if you can fill the toner, the chip will still assume that the cartridge is empty and will not allow the device to work. To get rid of this problem, a method for resetting a meter to zero was developed.

Toner software reset

Developers create additional service functions for their devices. Among them is a tool for resetting toner. It works only through the built.in display, so it is not suitable for all users. If you are a happy owner of a device with a screen, follow the following actions:

As you can see, it is easy to reset the paint using the software component. However, not everyone has a built.in screen, and this method is not always effective. For this reason, we recommend considering the second option.

Manual

Activation of the cartridge and resetting the sensor responsible for calculating the pages and manual locking of the device is suitable for all Brother models.

This fairly simple algorithm includes the following steps.

Connect the device to the mains. It is important not to connect a printer or All-in-One Printer to a computer or laptop during this process. It is also necessary to remove the entire paper.

Open the top cover and side cover. Remove the print drum from the case. You can remove it by carefully pulling it over. Separate the cartridge and drum, taking off the mounts.

Set the drum part to the place. Click on the sensor, which is located on the left side. Access to the device can be obtained by sticking your hand through the paper supply tray.

Hold the sensor in a pressed position and close the printer cover (All-In-One Printer), waiting for the start of the mechanisms. Let the sensor for a few seconds, and then squeeze again until the printer stops working, t.e. until the engine is completely stopped. Insert the previously extracted cassette into the drum block.

Sometimes, after all the manipulations described above, the device still does not detect consumables or may consider that it is empty. In such situations, it is recommended to extract the cartridge again and check it. Then, if it fails, the cartridge will need to be refueled or replaced with a working. The necessary steps, as a rule, can be taken independently.

Please note that some Brother models have constructive features that can complicate the replacement and further use of refueling cartridges.

It is important that all operations are performed correctly. If you have the slightest doubts about your own abilities and knowledge, it is strongly recommended to seek help from the service center.

How to reset a message about replacing the toner in the TN-2335/TN-2375 cartridges

  • Open the front cover;
  • Click and hold the “menu” button until the message “Reset TNR-STD A” reset on the screen;
  • Press the OK button;
  • The arrow up is selected “reset”;
  • Press the “Stop/output” button and close the lid.
  • Open the printer cover.
  • Click on the printer button “Clean” (Clear / button with a back arrow).
  • Press the Start key (Start / button tinted with a green strip).
  • Press quickly or. (buttons with arrows up and down).
  • Set on the screen 00 (two zeros) on the counter using the keys /- (up /down).
  • Press the OK button (between the buttons up and down).

How to reset a message about replacing the toner in the TN-1075/TN-1095 cartridges

Through the panel for models DCP-1602, 1610, 1612, 1623, 1510, 1512:

  • Click the menu. information about the device. reset photo bus
  • Set up and hold the OK button until the inscription is reset and exit
  • Press the start and right down the arrow
  • Arrows down or up, select numbers 00 on the screen
  • Click OK, the inscription “Adopted” will appear
  • Everything is reset, go back the button
  • We take out the toner-cartridge. In the device we leave only the drama cartridge (where is the photo bank)
  • Throw the hand through the paper tray and clamp the discharge flag. It is located in the left side of the dram-cartridge in a rectangular hole (in the photo)
  • Holding the flag clamped down, close the lid.
  • As soon as the engine starts (characteristic buzzing), let go of the flag and after 1.5. 2 seconds we clamp again. Hold to stop the engine.
  • We look at what the device writes on the scoreboard.
  • If you burn again “replace the toner”, repeat the procedure.
  • If we are ready, set the toner-cartridge back and use.

Reset from the printer Brother HL-1223W

Press the power button seven times when the device is turned on. (Both LEDs will blink twice, and the LED readiness will light up.)

Now Brother HL-1223W will continue to print until the toner ends.

Reset methods

First of all, it should be noted that many representatives of the range of the eminent brand, representing the country of the rising sun on the world office, have a similar design. over, many of them are equipped with cartridges of the TN-1075 series.

In this case, it is about the fact that in the vast majority of options an algorithm of actions when reversing the counters will be the same.

To date, there are 2 ways to get around the blocking of peripheral devices.

The first option is focused on multifunctionalists and printers equipped with their own displays. In the second case, we are talking about the universal method of isolation, which allows you to throw the counter to zero and restart office equipment for further full operation.

Program

The creators of modern printing equipment are constantly expanding the list of additional functions of their devices. It also includes an option that allows you to drop the counter on the printer and All-In-One Printer Brother.

It is important to consider that we are talking about models having an integrated display. Owners of such models to zero the page and paint counter need to do the following.

Connect to the network and start the peripheral device. It is important to remember that while the message “Wait” is displayed on the screen, no actions are taken.

Open (remove) the side cover, and then use the “Clean” button.

By pressing the “start”, start the corresponding process after the appearance of the request related to the replacement of the cartridge. Wait until the inscription “wait” on the display and press the arrows “up” and “down” several times. After “00” appears on the screen, you will need to confirm your actions using the “OK” button.

After the appropriate inscription appears, the side panel should be installed in place. Reload the printing device. After a reboot is carried out, go to the device menu, according to the points of which you can move using the arrows mentioned above. At this stage, it is required to check the condition of the counter. If all these manipulations are completed successfully, then this indicator will be 100%.

In practice, the software method of zeroing the meter and resetting the settings is the most simple and does not require significant time costs.

However, judging by the reviews of users, in some cases this solution to the problem is ineffective.

The alternative will be a universal algorithm of actions that is relevant for all peripheral devices, including those that do not have a display.

Manual

Activating the cartridge and resetting the sensor responsible for calculating the pages and blocking the device in manual mode is suitable for all Brother models.

This fairly simple algorithm provides the following steps.

Connect the equipment to the mains. It is important not to connect a printer or All-in-One Printer to a PC or laptop. It is also required to extract all the paper.

Open the top cover and side panel. Pull the drum from the body. You can get it, carefully pulling it over. Divide the cartridge and drum, removing fasteners.

Place the drum part back in its place. Click on a sensor that is located on the left side. Access to the device can be obtained by sticking your hand through the paper tray.

Holding the sensor in the clamped position, close the printer cover (All-in-One Printer), wait for the start of the mechanisms. Let the sensor release for a few seconds and squeeze again until the printing device stops working, that is, until the engine is completely stopped. Insert the previously extracted cartridge into the eardrum.

Sometimes, after all described manipulations, the technique still does not detect the consumable or considers it empty. In such situations, it is recommended to re.remove the cartridge and check it. After that, it will have to be filled or changed to the worker in case of failure. All necessary actions, as a rule, can be performed independently.

It is important to remember that some Brother equipment models have constructive features that can complicate the process of replacing and further operation of refueling cartridges.

It is necessary that all operations are performed correctly. In the presence of the slightest doubt about their own forces and knowledge, it is strongly recommended to seek help from the specialists of the service center.

How to reset different models?

As already noted, one of the most common cartridges that Brother devices are equipped with is the TN-1075 model. This, in particular, is about such samples of office equipment as DCP 1410R and 1512R, as well as HL 1110R and 1112R, MFC 1810R and 1815R.

In this case, the print node includes directly the cartridge itself and the Drama-UNIT series DR-1075 series.

There are 2 types of consumables and several ways to reset counters.

After installing a restored starting cartridge on these models, you will need to take the following steps.

  • Completely free the paper tray. Extract a printed module from the device case.
  • Disconnect the cartridge from the user drama, pressing the blue key located on the right.
  • Place the dramy-junet in place. On its left side, you can see a hole through which access to the button of the resettlement button of the meter of printed pages. It is important to consider that the process of reset and unlock the cartridge will be carried out with a cover closed, and you can get to it only through a paper tray. Therefore, it is required to remember exactly its location.
  • Press the zero button and close the printer lid. Do not worry about the risk of injuring your finger, since in this part of the device there are no mobile elements.
  • Hold the flag until the device is launched.
  • Let go for a short while and again, pressing it, hold it until the engine is turned off.
  • Wait for light indication in the form of a blinking green LED signaling the successful completion of the meter discharge. If this does not happen, the whole process should be repeated again.
  • Place the cartridge in the drama-yun.

The equipment setup algorithm when using the purchased cartridge of the TN-1075 model includes the following actions.

  • Without making excessive efforts, remove the lid. It is important to remember that in case of error, gear may be sprinkled.
  • Extract the left gear of the outer row. Find a gear in the form of a crescent under it and turn it until it stops.
  • Place the removed structure of the structure on its seat.
  • Close the slide block with a lid. It is important to carry out all the manipulations with maximum caution and make sure that the gear in the form of a crescent does not shift.
  • Screw the installed cover, after which you will need to return the cartridge to the drama-jun.
  • Place the collected printed module in the printer or multifunctional device.

In situations where the settings are required in laser models of office equipment of the Brother HL 2130R and 2132R, DCP 7055R and 7057R family, we are talking about the software and hardware method. The first embrace option can be considered by the example of the printer HL-2130R.

The programmatic method for resetting the indicators of the printed pages and unlocking meter is more relevant for the Brother brand ALL-ONE Printer. So, in the case of the DCP 7055R model, the following stages are provided:

  • Go to the device menu using the corresponding button;
  • Go to the point “General settings” and confirm your actions by pressing “OK”;
  • Select the command “Replace the toner”;
  • Go to the point “Continue” with arrows;
  • click “Clear”.

It is important to remember that such an algorithm can only be applied once. In case of failure, the release will only be hardware ground.

The user will need to take the following steps.

  • Run the equipment. After turning on the device, you can hear a characteristic noise.
  • As soon as the noise stops, open the lid on the front panel. Turn off the printer.
  • Press the GO key and hold it until the equipment starts to work again. It is important to make sure that there is no “Ready” indication.
  • Let the closed button.
  • Press the “go” twice, and then 5 more times in a row.
  • Close the front cover.

After all the listed manipulations, the indicator with the inscription “Ready” should glow evenly. At the final stage, it remains to reload. As a result, the laser printer will be reserved and ready for full operation.

Brother MFC-L5750DW сброс фотобарабана, сброс тонера, drum reset, toner reset, про принтеры

If you want to reset DCP 7057R settings, it will be necessary:

  • Activate All-In-One Printer and wait for the mechanism to stop making noise;
  • open the front cover of the device;
  • Depending on the modification, press the “Cancel”, “Stop” button or “Back”;
  • use the “Start” key;
  • press the arrow “up”, and then several times “down” until two zero are highlighted on the screen;
  • press OK and return the lid to its place.

How to reset the cartridge

The discharge algorithm is almost similar to the previous. Number will have to be done when the printer writes “Replace the Toner Cartridge”, “Toner” and other similar notifications on the built-in screen. Even after refueling the cartridge, the notification will remain, so it is necessary to reset the counting of the toner.

Brother DCP L2500 / L2700 Сброс счетчика тонера

Further, the printer will accept confirmation and show the notification that the discharge has launched.

Start print after exiting the menu (button “Stop/output”) and closing the cover.

When you can’t throw a counter

Determine only on condition that you are sure of the presence of powder in the toner cartridge. If the toner really ends, you need a refueling or buying a new full cartridge, t. to. With empty container, other printer nodes are at risk of failure.

You also do not need to throw off the counter if the message “Little Toner” will show on the screen. In such a situation, the seal will still be opportunities, but it begins to write this with the ending tuser in the printer, approaching the resource to zero.

Manual zeroing of Brother meter

It is better to resort to the manual method in the latter case, when the system reset was unsuccessful or not the display. Then you have to use the flag that interacts with the cartridge.

The method differs depending on the design of the printer. the cartridge is protruded through the upper or front cover.

The whole procedure is done only in the absence of paper in the tray and disconnected printing device from the computer.

Reset of cartridges TN-1075

Original monochrome cartridge (h/b), working with the “box” on the devices HL-1110R, HL-1112R, HL-1210WR, HL-1212WR, DCP-1510R, DCP-1512R, DCP-1610WR, DCP-1612WR, MFC- 1810r, MFC-1815R, MFC-1912WR.

  • Turn off the print as a button.
  • Remove the cartridge through the upper or front part.
  • Divide into two parts. with toner and ramparts (drama).
  • Put part with the shafts in the printer.
  • The dropping flag will appear on the left.
  • Remove your finger to the flag and click, putting your hand in the paper compartment.
  • Activate the closing sensor of the lid, lowering it, but without pressing the flag.
  • Turn on the printing equipment.
  • In case of noise, squeeze your finger and press once on the flag after a second, but without clamping.
  • After another 1 s, click until the device stops rotating and release.
  • The result is considered satisfactory when the warning flashes on the case anymore. a diode with an exclamation sign.
  • Gather the cartridge in the original state, insert into the printer, close the lid and try to print any document from the computer.

On some models, to throw off the counter, you should not apply the “9” stage from the instructions.

How to reset the TN-2280, TN-2290 cartridge meter

Actual for printers Brother HL-2130R, HL-2132R, DCP-7057R, DCP-7057WR, DCP-7055R, DCP-7060DR, DCP-7065DNR, DCP-7070DWR.

  • You should open the lid in front.
  • We take out the cartridge, disconnect the container with the toner, put it to the side, and connect the drama-orch back.
  • The cover in the lower left part is connected to the main part of the device with a small plastic lever. Make its disconnection and place Brother‘s apparatus inside the apparatus.
  • We imitate the closed condition of the cover. On the right side behind a small hole is a sensor. Take a thin object, for example, a match or a clip, and click on the sensor. The printer will “think” that it is in a closed state and will begin to prepare for work.
  • When the device is playing, namely, the shaft. to. First, cooling (fan) may turn on, click the flag twice at a speed of about 2 s for each press. That is, click and squeeze it off, and smoothly-in total, both presses will take about 4-5 seconds. We hold the second press, wait for the end of heating, lack of sound, and squeeze.
  • If the flag is not visible, it cannot be reached to the part, it can be highlighted with a lamp and pressed with a long item, for example, screwdriver.
  • After, the counter will be dropped.
  • We collect all the nodes in the reverse sequence of disassembly and try to carry out the seal.

The main problem of the step.by.step algorithm in the time of clicking, which is performed at the “5” stage. Sometimes it is required to do the same action many times, until it is possible to completely drop the toner counter.

How to make a reset yourself

Through the printer menu (programmatically)

First try to independently discharge through the built.in menu of the device.

  • Turn on the power on the printer.
  • You wait for the technique to no longer make noise and go into operating mode.
  • Open the lid on the front of the case.
  • On the case, click the “Cancel” key. In different devices, the button may be called “Stop”, “Back” or “Clean”.
  • Close the buttons “Start”, “Up” and “down”.
  • After, zeros should appear on the display.
  • Click on OK and close the lid.
  • Make a test printout (test printing).

Hardware reset

The embrace method is not suitable for cartridges that go in the starting kit with the DCP-7057R model printer, since there is no special flag in the design of the device.

  • Turn on the device on the network. Wait for the testing process to end.
  • Open the door on the case.
  • On the left side, find a lever that you disconnect and hide in the body.
  • Remove the refueling cartridge and divide it into two parts: a toner container and photos.
  • Place the drum back in the device, and the bunker with the powder temporarily remains aside.
  • With a flat screwdriver or any thin object, clamp the cover sensor, imitating the closure.
  • As soon as the gears are twisted, release the sensor and clamp again, then release and clamp again. The double press should take no more than 4 with.
  • When the gears and the motor stopped working, you can release the sensor.
  • The flag, which was hiding at the beginning of the discharge, returns to its previous position.
  • Connect the shaft and bunker in one cartridge and return to the printer.
  • Try to print a test page.

Khublings of a photo bank

In the All-In-One Printer Brother DCP-7057R, a dram-cartridge is installed, consisting of toner-tubes and a photo bank. On each of the elements there is a separate sensor that considers the resources used. The sensor algorithm contains that the drum can give out no more than 12 thousand. copies, and as soon as the figure is reached, the work is blocked, and a notification appears on the screen about the need to replace a photo bus.

If there is no damage on the surface of the photocell, it is not necessary to replace the shaft, to eliminate the error, it is enough to drop the counter.

printer, brother, reset, toner

Before reset, clean the shorter (charge roller). Put from the side to the side of the blue slider, which is located on the cartridge. If this has not helped to eliminate the problem, try to reset the counter.

  • Turn on the All-in-One Printer.
  • Wait until the technique warms up and prepare for work.
  • Open the lid and click on the “clean”.
  • On the screen should be displayed the message “You replaced the photo bank?””.
  • Put on the arrows “Up” and “Yes” alternately.
  • When it writes “accepted” on the display, close the lid.
  • Reload the device.

detailed instructions

Having completed the previous action, neatly insert the block with the photoval back to the printer.

Now you should go to the device for feeding the device where you need to pull out the paper.

Spend your hand through this tray, find a lever or sensor on the left and click on it.

  • Keep it in a state and at the same time slowly close the top cover of the printer.
  • As soon as you hear the characteristic noise of the device engine, you can let go of the lever. But literally after a second, click on him again.
  • It needs to be kept until office equipment does not warm up and calms down.
  • Thus, the reset of the toner toner counter Brother DCP 1512R is completed.

The highlighted value should be 100%

Open the printer lid, pull out a block with a photowall and collect the consumable material of the device. Having completed this procedure, insert the cartridge back into the device and make a trial print. It should be added that it is possible to start the printing process the first time you will not succeed. Therefore, if necessary, repeat the reset attempt to pause before letting go of the lever about 1 second after the organizational engineering engine is turned on again.

Watch the video to re.swing the toner counter on Brother DCP 1512R

Reset methods

First of all, it should be noted that many representatives of the range of the eminent brand, representing the country of the rising sun on the world office, have a similar design. over, many of them are equipped with cartridges of the TN-1075 series.

In this case, it is about the fact that in the vast majority of options an algorithm of actions when reversing the counters will be the same.

To date, there are 2 ways to get around the blocking of peripheral devices.

The first option is focused on multifunctionalists and printers equipped with their own displays. In the second case, we are talking about the universal method of isolation, which allows you to throw the counter to zero and restart office equipment for further full operation.

Program

The creators of modern printing equipment are constantly expanding the list of additional functions of their devices. It also includes an option that allows you to drop the counter on the printer and All-In-One Printer Brother.

It is important to consider that we are talking about models having an integrated display. Owners of such models to zero the page and paint counter need to do the following

Connect to the network and start the peripheral device

It is important to remember that while the message “Wait” is displayed on the screen, no actions are taken

How to set up a print printer over the network

Open (remove) the side cover, and then use the “Clean” button.

By pressing the “start”, start the corresponding process after the appearance of the request related to the replacement of the cartridge. Wait until the inscription “wait” on the display and press the arrows “up” and “down” several times. After “00” appears on the screen, you will need to confirm your actions using the “OK” button.

In practice, the software method of zeroing the meter and resetting the settings is the most simple and does not require significant time costs.

However, judging by the reviews of users, in some cases this solution to the problem is ineffective.

The alternative will be a universal algorithm of actions that is relevant for all peripheral devices, including those that do not have a display.

Manual

Activating the cartridge and resetting the sensor responsible for calculating the pages and blocking the device in manual mode is suitable for all Brother models.

Download and install drivers for the printer Brother HL-2130R

This fairly simple algorithm provides the following steps.

It is important not to connect a printer or All-in-One Printer to a PC or laptop. It is also required to extract all the paper

Open the top cover and side panel. Pull the drum from the body. You can get it, carefully pulling it over. Divide the cartridge and drum, removing fasteners.

Place the drum part back in its place. Click on a sensor that is located on the left side. Access to the device can be obtained by sticking your hand through the paper tray.

Holding the sensor in the clamped position, close the printer cover (All-in-One Printer), wait for the start of the mechanisms. Let the sensor release for a few seconds and squeeze again until the printing device stops working, that is, until the engine is completely stopped. Insert the previously extracted cartridge into the eardrum.

Sometimes, after all described manipulations, the technique still does not detect the consumable or considers it empty. In such situations, it is recommended to re.remove the cartridge and check it. After that, it will have to be filled or changed to the worker in case of failure. All necessary actions, as a rule, can be performed independently.

It is important to remember that some Brother equipment models have constructive features that can complicate the process of replacing and further operation of refueling cartridges. It is necessary that all operations are performed correctly

In the presence of the slightest doubt about their own forces and knowledge, it is strongly recommended to seek help from the specialists of the service center

It is necessary that all operations are performed correctly. In the presence of the slightest doubt about their own forces and knowledge, it is strongly recommended to seek help from the specialists of the service center.

printer, brother, reset, toner

Reset Toner counter to Brother DCP-1510/1511/1512/1518, MFC-1810/1811/1813/1815/1818

All-In-on Printer Brother (DCP-1510/1511/1512/1518, MFC-1810/1811/1813/1815/1818), having printed a certain number of pages, can stop the seal, although the cartridge is refueling and print it and print on it still. Today I will tell you how to drop the toner counter using the example of Brother DCP-1510 and restore the sensor if its flag is not shown. Now, probably, it is not entirely clear what it is about, so read completely.

Let’s start with the manual procedure for resetting the toner counter. There is nothing complicated:

  • Open the All-in-One Printer cover and take it out of it with toner-cartridge. Dram-cartridge, you can leave in place, it will not hurt.
  • We cross the finger through the paper supply tray in and clamp the discharge flag.
  • Close the All-in-One Printer cover, turn on the power. We are waiting for the start of the motor rotation.
  • We release for 1-1.5 seconds and press the discharge flag again, holding it until the engine stops.

If the counter has not been dropped the first time, we repeat the procedure again (we carefully read the algorithm of action). maybe you missed something or did the wrong time. I want to note that you should not reap on the flag like murderer, there is a chance to press it into the bowels of All-in-One Printer-shki forever. And then you have an unforgettable disassembly process. And without proper experience, you can easily turn your printer into a set of gears with springs and other plastic products. So it is better not to be hard, just slightly shift the flag to trigger the sensor.

I suppose everything worked out. Now I will tell my case. some kind of genius of refueling cartridges thought of the accountant to independently do such an operation. In general, the All-in-One Printer was given me with the words that “there is no more Pimpochka there” (this is, by the way about murderers).

Disassemble the Brother DCP-1510, in principle, it is not difficult, I even found on YouTube something like a video instruction (actually very stupid) when I tried to understand how the return spring of the toner-cartridge sensor flag is attached. It was because of her that the flag did not return to the right position, and in this case, force the All-in-One Printer will not be able to print.

Just about this nuance, the author of that manual on YouTube, apparently, deliberately kept silent. Why did I make such a conclusion? Yes, for the reason that the video was a similar question left unanswered. I can’t understand one thing for then to shoot the material if the key moment is missed?

Fortunately, in Google it was possible to find the official Brother DCP-1510 Service Manual (models DCP-1510/1511/1512/1518, MFC-1810/1811/1813/1815/1818), which has already become more or less clear how the return springs are established. According to the above link, you can download the manual from my blog, suddenly someone will come in handy.

Service instruction was also clearly made so that everything was easy, because here is a photo of the already installed flag with a spring. If your hands grow from the right place, then everything is going and works as it should.

If you think the article is useful, do not be lazy to like and share with friends.

File conversion in the Movavi Converter video. Full overview of the program independent repair of LCD Monitors Samsung iPhone XR on Tmall at a big discount. What’s the catch? Rumors: 4-inch iPhone 6c will be released in the middle of next year, the most popular tesers of components with AliExpress are the best alternatives to Kali Linux for hacking and testing

We dump the toner of the printer Brother

The instructions below will be optimal for most models of print devices from Brother, since they all have a similar design and are quite often equipped with TN-1075 cartridge. We will consider two ways. The first is suitable for users of All-in-One Printer and printer with a built-in screen, and the second is universal.

Developers create additional maintenance functions for their equipment. Among them is a paint reset tool. It is launched only through the built.in display, therefore, not all users are suitable. If you are the happy owner of the device with the screen, follow the following actions:

As you can see, the ground of paint through the software component is a simple matter. However, not everyone has a built.in screen, moreover, this method is not always effective. Therefore, we recommend paying attention to the second option.

Manual reset

There is a reset sensor on the Brother cartridge. It needs to be activated manually, then a successful update will occur. To do this, you need to independently extract components and perform other actions. The whole procedure looks as follows:

If, after resetting in two ways, you still receive a notification that the toner is not detected or the paint is over, we recommend checking the cartridge. If necessary, it should be refueled. You can do this at home using the instructions attached to the device, or seek help from the service center.

We have sorted out two available methods of zeroing the toner counter on printers and the Brother All-In-One Printer. It should be borne in mind that some models have a non.standard design and use cartridges of a different format. In this case, the best solution will be to use the services of service centers, since physical intervention in components can provoke malfunctions in the work of the device.

We are glad that we were able to help you in solving the problem.

In addition to this article, the site has another 13177 useful instructions. Add the site Lumpics.ru into bookmarks (ctrld) and we will definitely come in handy for you.

Describe what you didn’t succeed. Our experts will try to answer as quickly as possible.

BYRGPUB.COM 2023