Table of Contents

How to remove debris from the headphone jack?

  • Divide a disk into several parts.
  • Soak one piece in an alcohol solution and wrap a cotton swab around the plug from the headphones.
  • Insert the plug inside and clean it in a circular motion until the cotton wool turns white. It is logical that it will need to be changed several times.

How to turn off silent mode on iPhone?

How to turn off silent mode on your iPhone or iPad

  • 1. Ring / Silent switch on the left side of the device All iPhones and some iPads have a Ring / Silent switch on the left side of the device (above the volume buttons).
  • 2. Control center to disable silent mode

What to do if the phone shows that headphones are connected?

If your phone, smartphone on Android or iPhone shows that headphones are connected, but they are not there, you need:

  • Clean the connector from ordinary dirt with a thin cotton swab. Attention. do not do this with a needle, so as not to damage the contacts;
  • Clean the nest from oxidation using the same cotton swab and alcohol.

What to do if sound disappears on iPhone and headphones are written?

  • Insert and remove the plug from the headphone socket. There is a possibility that iOS did not have time to determine that the headphones were removed.
  • Connect other headphones. It can really help.
  • Reboot device.
  • Check the headphone jack.
  • Restore or update iOS.
  • Service center

How to turn off the headphone mode on Xiaomi?

Open the settings, find the section “All applications”. Find “Radio”, click on the name of the application. You clear the data by clicking “Clear All”. Only then turn off the headphones.

Why iPhone headphones may not work?

If the iPhone does not see the headphones, most likely there are three reasons for this. First, there are problems with the operating system. Sometimes this problem can be fixed by simply rebooting the device, but more often than not, flashing will help fix this. Second, the connector may be dirty.

Where are the headphone settings in the iPhone?

Configuring Airpods Settings on iPhone

  • Open the Airpods case.
  • On iPhone, open Settings Bluetooth.
  • Tap the button next to Airpods in the device list.
  • You can follow the steps below. Change the name of your Airpods. Tap the current name, enter a new name, then tap Done.

What to do if there is no sound in the headphones on the phone?

You may have accidentally muted the sound. 2. Try plugging in headphones, holding down the volume up button, and pulling out the plug from the headphone jack. Also try pulling and inserting the headphone plug several times.

SEkTARIANSBLOG

In some cases, after listening to music on an iOS device through headphones, the sound in the speakers completely disappears. Sometimes, the device displays a volume icon that does not respond to changes in the sound level. The problem is rare enough, but it still happens.

Why iPhone thinks it has headphones connected when it isn’t?

The bottom line is this: you listen to music on your iPhone, iPod touch or iPad, take out the headphones and system notifications, sounds, ringtones are no longer played through the built-in speaker. There may be several reasons, but the most common are the following:

  • Failure when removing the plug from the device.
  • You unplugged the headphones while the device was performing internal operations.
  • You have used an improper quality earphone or headset.
  • 3.5mm jack problem.

Software or hardware problem

In fact, not only hardware problems can lead to such an incident, but also an operating system failure. As practice shows, in the vast majority of victims, the problem manifested itself precisely because of a banal mistake. What can be done in this case:

Insert and remove the plug from the headphone socket. There is a possibility that iOS did not have time to determine that the headphones were removed. If the user abruptly pulls out the plug, the system can continue to believe that they are still connected. Sometimes it is enough to insert and remove the earbuds several times to get the device working again.

Connect other headphones. This can really help. If the problem is with the connected accessory. Yes, yes, especially if it costs less than 300 rubles.

The problem of low-quality accessories is not new, but to make sure that it’s not just your headphones, it would be a good idea to try an alternative.

Reboot device. A simple reboot of your device might fix your problem. Coupled with a Chinese headset and a crash in the OS, it is quite possible to achieve that the smartphone does not understand what happened.

Check the headphone jack. If none of the above methods helped you, then it’s time to apply the deduction method. What if something got into the 3.5mm jack on your iPhone? Various contamination can lead to short circuiting of the contacts of the headphones and smartphone. Take the flashlight and look inside. If something really got there, you can use a toothpick or cotton swab to clean the connector.

Remember that everyone needs a measure. Pressing with all your strength and scraping along the walls is also not the best option.

Restore or update iOS. If there are no problems with either the connector or the system, you can use a more radical method.

Try updating iOS from DFU mode. There is a chance that after the update everything will fall into place. Especially if you had any system tweaks installed.

Jailbreak?

Unfortunately, if the methods described above did not lead to the desired result, then the last thing that can be advised is to contact an authorized service center. You should not try to disassemble the device yourself, even if you are confident in your abilities. It often happens that violations are associated with damage to the printed circuit board after moisture ingress. Some users have reported a sound issue after iPhone has been in water or damaged by spills.

moisture headphone jack

Even if you do not spill liquid on your Apple device, it is still possible that the iPhone thinks the headphones are connected to water if its surroundings are wet.

Place the hair dryer directly opposite to dry gently inside the moisture. By the way, using a cloth to absorb moisture is useless.

Tips and tricks for disconnecting iPhone headphones

When your iPhone thinks the headphones are connected but not, you can also try some traditional solutions to fix the problem. First choice. force restart iPhone. Hold and press the Power and Home buttons until the Apple logo appears, especially when the iPhone screen is unresponsive. Alternatively, you can reset all settings to turn off headphone mode on iPhone. This is an operation that can restore all of your personal settings back to their original state without data loss.

the headphone jack is physically damaged

It is also possible that your headphone jack has received physical damage before. Despite the physical damage, misuse and use of universal headphones are also to blame.

[How to fix] iPhone thinks headphones are plugged in

“When I try to change the volume on my phone, it says“ Headphones ”instead of“ ringing ”. It seems to me that my iPhone 6s is stuck in headphone mode, so I plug in the headphones and then turn on the speakerphone. But I still can’t listen to music or video unless headphones are connected. Can anyone explain why my phone says the headphones are plugged in but not really? “

It is a common problem that your iPhone thinks the headphones are plugged in when they are not. You are capable of fixing an iPhone stuck in headphone mode on your own instead of going to the repair shop directly. Below are the causes and solutions to fix the problem that you unplug your headphones when your iPhone still thinks they are plugged in. In short, read and learn easy ways to quickly exit headphone mode.

READ  Photos taken with iPhone 7 plus

abnormal disconnection of headphones

If you unplug your iPhone headphones too quickly, your iPhone may not have recognized the disconnection in time or even thinks that the headphones are plugged in.

This way, you can plug in the headphones and then unplug them from the headphone jack several times. As a result, your iPhone can detect the iPhone headphone disconnection and exit the headphone mode automatically.

liquid enters the headphone jack

If you accidentally spill coffee, juice, or other liquid on your iPhone, the spilled liquid may still remain in the 3.5mm headphone jack. Thus, your iPhone thinks the headphones are connected to water, which can often cause the touchscreen not to work because the touchscreen is close to the headphones.

To dry out the water in the headphone jack, you can turn off your iPhone and use a hair dryer to fix it. Otherwise, you can use a Q-tip or a cotton wool needle to thoroughly wipe off the liquid.

iOS update

Updating your iPhone to the latest version of iOS 12 can fix many bugs and software bugs without any problems. If you’ve ignored multiple iOS updates before, it may cause your iPhone to stuck in headphone mode.

Back up your iPhone with one click using iOS Data Backup & Restore first. Later, open Settings and select General to find Software Update. Click “Install Now” below to update your iPhone and exit headphone mode.

Make a backup before fixing “iPhone thinks headphones are plugged in

Whenever you try to fix the iPhone thinks the headphones are plugged in or As for your iPhone, be it software or hardware, you should back up your data. Now when you go to the Apple Store and ship your iPhone, they have no time to back up your data and restore after a fix. that would be great, but they are very busy!

How to Use iMyfone iTransor iPhone Data Exporter

Before trying to fix an iPhone thinks the headphones are plugged in, follow our guide below. These steps will show you how to back up your iPhone data as quickly as possible.

#one. Download, install and run iMyFone D-Port Pro (Now iMyfone iTransor) on your computer.

# 2. If you haven’t connected your iPhone yet, connect it with a lightning cable.

# 3. Click on “Back up and export from device”, and then on the next screen select “Export data”.

#four. Browse through the different data types and click Select All Or select the specific data types you want to back up.

#five. Click NextContinue. Your iPhone will be scanned quickly, and once the scan is complete, you can view the data stored on the device.

# 6. Again, check the box next to “Select All” Or browse the files that were found and select specific files to back up.

# 7. Finally, click “Export” and choose a location to save the data on your computer.

iMyFone via iTunes is definitely perfect. You can select specific files to back up, preview the data before backing up, and save it anywhere.

About iMyFone Fixppo iOS System Recovery

This program is specially designed to fix iOS problems like iPhone thinks the headphones are working. But things go much further, and here are some key features:

  • Includes multiple data recovery options.
  • Compatible with all latest iOS versions.
  • Easy to use, safe and reputable.
  • Eliminates any iOS issue, including getting stuck in recovery mode, unable to update apps or upload photos, apps won’t load on iPhone, iPhone alarm isn’t working, contacts on iPhone are missing, or iPhone camera won’t focus.
  • Using standard mode to troubleshoot iOS issues ensures your personal information is safe.

Given how flexible this program is, we recommend using it first. It will quickly fix your iPhone, it has a lot to offer and you will find it useful for many different activities.

Fourth: impure headphone port

Not everyone understands this, but iPhone ports get dirty very quickly. Look at your speakers and headphone port with a torch. you will notice dust accumulation.

You can try using a vacuum cleaner to remove dust. A safer option would be to use the edge of a clean rag to clean the port. Make sure you are not using sharp or metal objects as this may cause permanent damage.

Reasons for “iPhone thinks headphones are in

Second: water or condensation in the headphone port

Water and condensation can make your iPhone believe your headphones are connected. This could be due to spillage of juice on the device or if it was in your bathroom while you were showering, possibly condensation.

If your iPhone thinks the headphones are plugged in and has been working for a while, it is unlikely that they are. The liquid will already dry and will not cause you any problems.

You can use a hair dryer to dry quickly, but don’t place it too close. Set your dryer to the lowest setting to prevent any components from melting inside your iPhone.

16 Easy Ways to Fix iPhone Stuck in Headphones Mode

iphone, shows, headphones, connected

By the way, click here to find out how to fix People Can’t Hear Me on My iPhone And How to Connect a Microphone to iPhone Easily.

What is iMyfone iTransor (Formerly: iMyFone D-Port iPhone Data Exporter)?

This part of iMyfone iTransor. best way to fetch data from iOS device. It offers many possibilities to manage your data, it is very flexible and the best way to ensure that your iPhone data is properly backed up.

  • Back up data directly to your computer to fix iCloud contacts not syncing.
  • Preview your iPhone data before you made a backup.
  • Download and extract backups from your iCloud account.
  • Ability to retrieve various types of data.
  • Compatible with the latest iOS and iPhone models.

The flexibility this program alone offers is fantastic. When it comes to data extraction, this is undoubtedly the best software out there.

iPhone Thinks I Have Headphones Plugged In. How To Fix

First: software problems

The most common reason the iPhone thinks the headphones are plugged in. this is due to the installed software. Hardware is a less common cause, but we’ll come back to that later.

Hopefully you will have a software problem. If so, we can identify and fix it fairly easily and without any other problem. Do not worry. many people think that software problems mean a factory reset is required, but this is not always necessary.

One quick fix might be a simple restart. Hold the power button, swipe the slider, and after your iPhone is off, go ahead and turn it on. If this does not solve the problem, then we recommend using iMyFone Fixppo (iOS System Restore).

Constant “headphone mode” (even when they are not). iPhone, what are you doing?

Hey! I face a similar problem, if not every month, then every six months for sure. He loves to smell my iPhone 5S (and the constant “headphone mode” is still “flowers”), there’s nothing to be done 🙂 And given the fact that this malfunction is easily solved, it never even occurred to me to write instructions on this topic.

But quite recently, a small reason did appear

An acquaintance approached me, showed me the iPhone 6 and asked the question: “Why is there no sound from the speakers?” We tried to increase the volume, and the iPhone shows that headphones are connected to it and adjusts the volume in them. At the same time, of course, there are no headphones and cannot be. the 3.5 mm jack is empty.

Looking ahead, I note that we fixed the problem in just 1 minute. The man left happy, but I thought that a small note on this topic still needs to be written. So, we bring the iPhone to life and turn off the stuck “headphone mode”. Let’s go!

Some kind of long introduction came out, but don’t worry, in 95% of cases the solution will be very quick 🙂 And here’s what you need to do

  • Reboot. An elementary action, but it is worth starting with this. over, the so-called Hard Reset helps the best (how to do it for different iPhone models). Don’t worry, your data won’t be lost.
  • Clean the connector. The fact is that sometimes 3.5 mm or (if your iPhone model is “seven” and older) the Lighting connector may “glitch”. the phone will think that the headphones are turned on even when they are not physically present.

The most common causes are moisture, oxides and dust clogging.

A simple example. Carry your phone in your dust is clogged. iPhone thinks that dirt is headphones.

  • We take a piece of paper, a match, a toothpick, a cotton swab, etc. Attention! It is not necessary to use metal objects (knitting needles, needles, pins), as the contacts can be damaged.
  • Carefully (carefully!) We take out all the dirt.
  • Some even dip a cotton swab in alcohol and clean the connector that way. over, it seems to help. But in my opinion, doing this is not worth it. after all, if you overdo it with liquid, then the consequences will be unpleasant. We don’t need that 🙂

Interesting fact. Since Apple technical support cannot advise you to poke around in the connector with various objects, they have another solution in this case. They suggest inserting and removing the headphones several times. Repeat the procedure until the iPhone stops constantly showing connected “ears”.

READ  How to untie Apple iwatch from iPhone

Honestly, this could have ended, but there are those very remaining 5% that will not be helped by all of the above. And that’s why.

The fact is that internal damage to the iPhone can be the cause of the lack of sound from the speakers and the problem of “always connected headphones”. The headset connector is located on the so-called top ribbon cable (iPhone 4S and younger) and the lower ribbon cable (iPhone 5 and older).

In especially advanced cases (for example, prolonged contact with liquid), one external cleaning is not enough. you will have to change the whole train. Fortunately, this rarely happens, the repair is not very difficult, and the cost is not prohibitively high. they will do it quickly and will not take a lot of money. But I, as usual, sincerely hope that in your case everything will be solved in the simpler ways described above.

Note. I finished the article and thought that I did not even advise the standard things (which absolutely everyone writes about). update the firmware, restore iOS, etc.

So why did the author do this and hide this “very important information”? Yes, because if the iPhone hangs on the headphone mode due to a simple “glitch” of the system, then a reboot is more than enough. And flashing and updating is already too much. In any case, there have never been such stories in my memory. Although if all else fails and you are going to carry the iPhone for repair, then as a last resort, you can try. Why not?

Constant “headphone mode” (even when they are not). iPhone, what are you doing?

Hey! I face a similar problem, if not every month, then every six months for sure. He loves to smell my iPhone 5S (and the constant “headphones mode” is still “flowers”), nothing can be done 🙂 And given the fact that this malfunction is easily solved, it never even occurred to me to write instructions on this topic.

How to Exit Stuck HeadPhone Mode on iPhone 6 & iPhone 6s & Plus

But quite recently, a small reason did appear

An acquaintance approached me, showed me the iPhone 6 and asked the question: “Why is there no sound from the speakers?” We tried to increase the volume, and the iPhone shows that headphones are connected to it and adjusts the volume in them. At the same time, of course, there are no headphones and cannot be. the 3.5 mm jack is empty.

Looking ahead, I note that we fixed the problem in just 1 minute. The man left happy, but I thought that a small note on this topic still needs to be written. So, we bring the iPhone to life and turn off the stuck “headphone mode”. Let’s go!

Some kind of long introduction came out, but don’t worry, in 95% of cases the solution will be very quick 🙂 And here’s what you need to do

  • Reboot. An elementary action, but it is worth starting with this. over, the so-called Hard Reset helps the best (how to do it for different iPhone models). Don’t worry, your data won’t be lost.
  • Clean the connector. The fact is that sometimes 3.5 mm or (if your iPhone model is “seven” and older) the Lighting connector may “glitch”. the phone will think that the headphones are turned on even when they are not physically present.

The most common causes are moisture, oxides and dust clogging.

A simple example. Carry your phone in your dust is clogged. iPhone thinks that dirt is headphones.

  • We take a piece of paper, a match, a toothpick, a cotton swab, etc. Attention! It is not necessary to use metal objects (knitting needles, needles, pins), as the contacts can be damaged.
  • Carefully (carefully!) We take out all the dirt.
  • Some even dip a cotton swab in alcohol and clean the connector that way. over, it seems to help. But in my opinion, doing this is not worth it. after all, if you overdo it with liquid, then the consequences will be unpleasant. We don’t need that 🙂

Interesting fact. Since Apple technical support cannot advise you to poke around in the connector with various objects, they have another solution in this case. They suggest inserting and removing the headphones several times. Repeat the procedure until the iPhone stops constantly showing connected “ears”.

Honestly, this could have ended, but there are those very remaining 5% that will not be helped by all of the above. And that’s why.

The fact is that internal damage to the iPhone can be the cause of the lack of sound from the speakers and the problem of “always connected headphones”. The headset connector is located on the so-called top ribbon cable (iPhone 4S and younger) and the lower ribbon cable (iPhone 5 and older).

In especially advanced cases (for example, prolonged contact with liquid), one external cleaning is not enough. you will have to change the whole train. Fortunately, this rarely happens, the repair is not very difficult, and the cost is not prohibitively high. they will do it quickly and will not take a lot of money. But I, as usual, sincerely hope that in your case everything will be solved in the simpler ways described above.

Note. I finished the article and thought that I did not even advise the standard things (which absolutely everyone writes about). update the firmware, restore iOS, etc.

So why did the author do this and hide this “very important information”? Yes, because if the iPhone hangs on the headphone mode due to a simple “glitch” of the system, then a reboot is more than enough. And flashing and updating is already too much. In any case, there have never been such stories in my memory. Although if all else fails and you are going to carry the iPhone for repair, then as a last resort, you can try. Why not?

Warning

What to do if an unnecessary icon (indicating that the headphones are connected) is on, and besides, glitches are already starting to appear in the phone, that is, other applications? There are 2 types of recommendations here:

  • Things You Can Really Do On Your Own.
  • Activities that will not be 99.99% successful in the conditions of artisanal performance.

Specifically, within the framework of this section, it is proposed to dwell on the latter.

For example, you can definitely never use such tips and tricks:

  • “Try to install a new OS firmware! I know a cool site: if something doesn’t work on my smartphone, then I always take applications from there In general, everything is free! “
  • “Look, buddy, take a clerical knife and carefully undress the halves of the apparatus. Take off the top panel, in short “
  • “Did you drop it in the bathtub? It’s okay: take a hair dryer and blow it through the jacks. Hold the hair dryer longer “
  • And even: “Try reinstalling the system. Himself, of course. why spend money! “

Modern devices are ultra-compact gadgets. These are far from those push-button phones that were disassembled and reassembled like a designer. As practice shows, opening the smartphone cases outside the conditions of a professional workshop leads to irreversible mechanical damage.

Using a hair dryer is also not a safe method. Since the air in the device also passes through the incandescent spiral, getting very hot (therefore, the hair here dries quickly). Modern smartphones contain many parts and plastic, so that plastic damage (melting) can be inflicted on them with the help of “blowing” a hair dryer to one point much faster than many initially thought.

It is also better to trust specialized specialists for any actions with the software. Even if your phone is on Android (and here the principle of open source code is used), then most users still do not know how to properly perform even the initial installation of the OS.

The principle of open architecture has long become a convention, since the very device of applications and systems contains too many nuances that must be consistent with each other for the applications to work correctly.

An untrained user can never cope with the proper installation of all settings.!

Reset application data. Radio

The next way to remove the headphone icon on the phone, even if physical prevention measures were ineffective, is to reinstall the profile software. If the headphones do not turn off, then you should “demolish” the software that is responsible for this option.

This clearly demonstrates the need to download control applications separately, and not to use phone firmware. In this case, it will be easier to localize the problem.

Next, the phone either shows that in order to use the headset, it needs to install a profile application (and then you reinstall it), or the headset icon does not disappear and then the OS should be reinstalled (for which we contact the specialists).

In addition, this method can also work: connect an app that directs the sound to the correct output. It could be Toggleheadset in the Play Market for Android. This often works.

Eliminating the application responsible for the radio also helps. Once the problem with your headset is resolved, you can reinstall it. The principle here is simple. we eliminate everything that may interfere with the correct operation of the headphones, and then we sequentially install everything again.

Sound driver update

If none of the above methods work, try uninstalling the current driver and replacing it with a new one.

Open the system search bar, type “Device Manager” and click on the found result.

Expand Sound, Game and Video Controllers. Right-click on the audio hardware to open the context menu and go to “Update drivers”. Select the option to automatically search for updated drivers.

READ  iPhone 11 holds in hand

Cleaning with special liquid

This method of removing contaminants is professional, so it is not available for the vast majority of users. Such equipment is very expensive, and in order for its purchase to be justified, it is required to put such cleaning literally on the stream.

Removing the Realtek HD Audio Sound Manager

If headphones are not showing in audio devices, try uninstalling Realtek HD Audio Manager. Despite the fact that the program is very easy to use, it sometimes causes problems. If after uninstalling the sound starts playing, try installing the manager again and check their functionality.

Type in the Windows search box “Control Panel” and go to the found result.

Switch the view mode to “Categories” and select the “Programs” section.

Find Realtek HD Audio Driver and after right-clicking on it select “Uninstall”. Follow the instructions to uninstall it.

After the process is complete, restart your computer and check if the headphones are displayed in playback devices. If successful, try reinstalling the program again.

iphone, shows, headphones, connected

The headphone symbol is constantly on. How to remove?

This software error causes negative emotions for smartphone users not only because they do not want to see anything superfluous on the screen. Unauthorized appearance of an additional sign (symbol) may indicate the incorrect operation of the program, which can interrupt the regular operation of other applications and even the entire OS of the phone.

For example, it suddenly turns out that all calls are switched to speakerphone.

The fact that the headphone icon does not disappear (although it should) is a symptom indicating some software metastases on your phone. It is possible that this could have happened due to the following reasons:

  • Ingress of moisture inside the smartphone case.

This is the most popular reason for all possible software glitches on the phone. Careless operation leads to oxidation of microcontacts inside the protective case and to temporary or permanent incorrect operation of the software.

  • Dirt gets into the socket.

Another popular reason why expensive smartphones fail and, in particular, why the headphone icon appears and does not turn off. Here, the situation can only be corrected by a timely appeal to the service center.

However, the headphone icon may appear and not disappear for more complex reasons related to bugs in the software, related to incorrect firmware or installation of “pirated” applications. It also requires the help of qualified specialists.

Troubleshoot audio problems

You can try to resolve audio playback problems using a troubleshooter. To do this, follow these steps.

Press the Win I combination to enter Settings or click the gear icon in the Start menu. Open the “Update and Security” section.

Go to the Troubleshoot tab, expand Audio playback and run the troubleshooter.

Follow the instructions on the screen to complete the process.

Sometimes it happens that a symbol of the presence of an active (that is, connected) headset or headphones may appear on the display of your mobile phone. But at the same time, your headphones are disconnected, that is, you cannot receive calls, and the player does not play the scale (when you change the volume, you will still not hear anything). At the same time, no matter how hard you try, this icon does not disappear anywhere. This is a fairly common bug that spoils the nerves of many. There are several reasons for this problem and a number of options for its removal. How to remove the headphone icon on your phone. we’ll tell you further.

The phone shows that headphones are connected: what to do?

On almost all modern models of phones and smartphones, when accessories are connected, an indicator appears that notifies the user of what exactly was connected (headphones, Bluetooth headset, etc.).

But, if the phone shows that headphones are connected although they are not, then there is definitely a problem. Below we will tell you how to solve it.

Possible problem

If the phone says that the headphones are connected, but restarting does not help, then in the case of wired headphones there may be a problem with the connector.

The connector means the headset jack. 3.5 mm, USB Type C, Ligthing

It is possible that a foreign object or moisture has got into it.

The ingress of moisture on the contacts can cause not only constant system failures, but also provoke corrosion, which, once started, will disable the entire device in a short period of time.

Possible problem

Your phone probably “thinks” that the headphones are plugged in due to a system failure. This may apply to both wired and wireless headphones.

Failure can occur for the following reasons:

  • The phone has been used for a long time and the motherboard has overheated
  • The headphones were removed while the melody was playing, as a result of which the device has not yet had time to complete all previous processes and freezes
  • The smartphone was dropped along with the connected headphones, after which the headset was hastily removed.

The best solution in this case is to simply reboot the phone. If the problem was a system glitch, after a reboot, the indicator will turn off by itself.

If a serious system failure occurs and the reboot does not help, then in order to fix it, you will need to reset the smartphone settings to the factory settings. Before performing it, be sure to back up your data.

What to do?

First of all, inspect the headphone jack for foreign objects. These can be both specks and pellets from clothes. They can be removed carefully with a toothpick or needle. But be careful not to damage the contacts.

If there are no foreign objects, check for moisture. If it is there, you can carefully remove it with a needle, after winding a little cotton wool around it. In addition, you can dry the connector with a regular hair dryer in a cold mode.

If you are well versed in the structure of your smartphone, you can try to disassemble it and clean the contact area of ​​the headphone jack with a special compound.

However, given that many modern models are made very cleverly, it is better to abandon independent manipulations and hand over the device for repair to a service center.

In this article, we told you what to do if the phone says that the headphones are connected. We hope the advice helped you. If you have questions. write in the Комментарии и мнения владельцев.

Read other instructions for mobile phones and smartphones in the section Instructions and help for smartphones on our website.

Reboot your device

If increasing the volume with the button did not help, then something is wrong. First of all, restart the phone, and then check the sound first of the native speakers, and then in the headphones.

Moisture ingress

Moisture getting inside the phone is unpleasant. Both certain functions and the phone in general may fail. The same goes for sound.

As soon as the phone is taken out of a humid environment, you must immediately do the following simple steps:

  • de-energize the device;
  • remove residual moisture.

What to do in no case:

  • dry the phone on the radiator of the heating battery;
  • check the phone for performance after self-drying;
  • put the device in a container with rice. It’s a myth, rice won’t help you in any way.

Headset jack problem

If the sound on the iPhone only works through the headphones, then there is a problem with the jack. Clean it up, look inside. Be sure to inspect for mechanical damage.

The main signs that there are problems with the mini jack (3.5) connector (headphones with the following parameters must be disconnected):

  • the phone does not record sound through the voice recorder;
  • your interlocutors cannot hear you in speakerphone mode;
  • by pressing the volume button, you do not adjust the volume of the call, but the volume in the headphones;
  • music does not play through the main speakers, but when headphones are connected, everything is in order;
  • the headphones broke and the plug remained in the jack. This happens, of course, rarely, but it does happen. If the plug remains inside, then the iPhone thinks that no one has disconnected the headphones, that they are working.

If you have the above listed problems, we advise you to carry your smartphone for repair. Do not try to do anything yourself, Apple’s equipment is very delicate, it needs only professional repair.

  • audio codec;
  • sound control chip.

They can be damaged both when water gets inside the case, and when subjected to strong impact. In case of damage, you only need to replace it, there are no other solutions. By the way, if the above microcircuits do not work, then the sound when you call will work on.

How to configure TP-Link tl wr741nd router? All information is here.

Mechanical deformation

In case of mechanical damage to the phone, there is a high probability that either the speakers or the sound control microcircuits will fail. In both the first and second cases, it is better not to try to solve the problem on your own, since you most likely will not be able to disassemble the iPhone correctly the first time. Damage something, and repairs will cost several times more.

BYRGPUB.COM 2021