What to do if the iPhone does not turn on and the apple hangs

An easy way to solve the problem is to reboot the device using the Home and Power buttons, which must be held down and held for 10 seconds. If the reboot does not help, then an update or flashing of the device will be required. To do this, run iTunes on your PC.

Step 1: Launch iTunes on your computer and connect the USB cable (you don‘t need to connect the USB cable to the phone yet). Turn off the iPhone while holding the HOME POWER buttons (on iPhone 7, you must hold HOME and. Volume)

Hold down the HOME button and connect the USB cable to the device. Hold the HOME button until the iTunes logo and a plug image are displayed on the device screen.

A notification will appear on the computer screen that the device is in recovery mode

Step 4. Now just click on the Restore button Before restoring your iPhone to factory settings, your computer will need to download the latest version of iOS from Apple’s servers. In this case, the phone will lie with the screen off and show no signs of life. Even with a good fast internet connection, the download process can take 40 minutes or more. If your internet connection is unstable or slow, the process may never complete. Connect to a faster Wi-Fi connection.

iPhone 6/7/8 / X / 12 won’t turn on lit apple on and off, how to solve?

Sometimes a glowing apple on the iPhone screen is on, it hangs and turns off, then the screen will be black, it does not respond to pressing. There are quite a few probable reasons for the appearance of this trouble. Today we’ll look at the most common iPhone won’t turn on problems and try to find a solution.

The reasons why the apple burns but the iPhone does not turn on

Before referring to the instructions, you need to understand what caused the iPhone to not turn on and the apple on the black screen burns. The following reasons are listed:

Sometimes the battery is discharged, the phone is completely discharged, so an apple appears. Try plugging in your charger and after waiting 20 minutes, try turning your iPhone back on.

The phone freezes when you turn it on, probably a breakdown of the “Power” button. Occurs when disassembling an iPhone.

The device does not boot further than the apple. problems with the power supply of the device This often happens with phones during network jumps when charging.

Charging controller is broken, there was a power outage.

Problems with the power supply circuit of the device. The device lay on the charge during a strong power surge.

Problems with the motherboard, while the phone itself may even boot sometimes and even work for a while. True, the glowing apple on the iPhone screen will appear more and more often until it stops starting normally at all.

DFU mode

If your iPhone won’t turn on, even after the one tried above, there remains one more way. restore iPhone in DFU (Device Firmware Update) mode. Follow the link and follow the step-by-step instructions.

There is an easier way to solve this problem, using Tenorshare ReiBoot, one-click you can enter recovery mode and exit recovery mode. Logging in or out can help you solve “the apple is on but the iPhone won’t start”.

Download Tenorshare ReiBoot for Mac or Windows from the official website. Install it. Connect your iPhone on board to your computer (or Mac) using a USB cable.

We launch the program. You will see several buttons, but only one will be active. “Enter recovery mode”. Click on it and wait for a while. You will see the iTunes logo on the display of your iPhone.

Then press the button “Exit recovery mode”. We are waiting for the time it takes to restart your iPhone. Done!

Useful software for iPhone / iPad is always in great demand among users and often ends up in the collection of selected programs. Be sure to take note of the Tenorshare ReiBoot utility. It allows you to enter or exit iPhone recovery mode in the easiest and fastest way. And it will help when standard system methods do not work.

How to get rid of the “white apple” if the iPhone is not jailbreakable?

If the “white apple” appears on an unjacked iPhone, the first thing the owner of the device needs to do is to reboot the smartphone and after 5 minutes try to call it. What will such a test give? It is very simple: if the call is in progress, it means that the download of the gadget is interrupted at the very last stage. therefore, it is possible to access the file system of the mobile device. And if there is access to the file system, then there is an opportunity to demolish the “buggy” applications that provoked the problem of the “white apple”.

You won’t be able to make changes to the iPhone’s file system through iTunes. You will have to use one of the alternative file managers. for example, iFunBox or iTools.

Connect the gadget to a PC and, through the file manager, erase recently downloaded applications one by one (by analogy with tweaks), alternating uninstall operations with checks.

Let’s return to the test with a call: what to do if the result of the experiment is negative and the call on the iPhone with the “white apple” does not go? Such a test result indicates a hardware problem: only technical docks, masters of a soldering iron and a multimeter can fix it with their own hands. If you cannot call yourself a “guru” of mobile technology, you should not open the iPhone and go into the filling. you will only make it worse. Better hand over the broken “apple” gadget to the caring hands of the service center masters.

iPhone won’t turn on: apple is on and off

Salon consultants make a helpless gesture: iPhones, which do not turn on after the “apple burns”, are regularly brought under warranty. Buyers do not even know that they can solve this problem on their own. and it will take a minimum of time to fix the problem.

The notion that Apple technology is the most reliable is outdated; now iPhones are regular “guests” of service centers. One of the most common iPhone malfunctions is popularly called the “white apple”: the gadget starts up, the “apple” burns on the screen for a long time, then the screen just goes out.

Users, not knowing what to do in such a situation, immediately carry their gadgets to service centers, although they can also fix the malfunction with their own hands. without material expenditures or a 45-day wait for warranty repairs. How to get rid of the “white apple”?

What to do if iPhone won’t turn on after jailbreak?

Turn off your smartphone.

Hold the volume up button on the side of your iPhone.

With the key pressed, try to start the mobile device.

An iPhone turned on in this way boots without programs from Cydia. If the gadget turns on normally with the volume key pressed, the point is definitely in one of the tweaks.

It will not be possible to establish exactly which jailbreak tweak is problematic. erase the programs one by one (starting with the one that you downloaded last) and after each operation try to start the smartphone in the usual way.

If the smartphone does not turn on even with the volume key pressed, the user has no choice but to jailbreak. We talked about several ways how to remove jailbreak from iPhone. in case of the “white apple” problem, it is recommended to flash the device.

Re-flashing. it just sounds scary, in fact, the procedure is quite simple:

Launch iTunes and connect the iPhone to PC with a cable.

Put your smartphone in DFU mode. If this is not done, the PC simply will not see the connected gadget. You can find detailed instructions on how to activate DFU-mode on iPhone in our article on DFU-Mode.

ITunes will notify you that iPhone has been detected in recovery mode.

Click on the “Restore iPhone” button.

iTunes itself will download and install the new firmware on the gadget. You just have to wait for the completion of the procedure.

Re-flashing in the described way is fraught with the loss of all data. the user will receive a completely “clean” device.

IPhone Freezes When Turning On: Possible Causes

Ordinary iPhone users are often victims of wars between hacker teams. the very ones that develop jailbreaks. For example, the desire of the Evad3rs group to overtake the rest of the teams and release the iOS 7 jailbreak first led to the fact that the problem of freezing Apple gadgets on the logo in 2013 became an epidemic. Due to the “dampness” of the Evasi0n 7 jailbreak utility, smartphones got into a cyclic reboot. they switched on and off sequentially until the charge ran out.

Unsuccessful jailbreak and installation of a “buggy” tweak are two reasons that in the vast majority of cases cause a “white apple”!

However, if the iPhone turns on before the “apple” and turns off, this may be caused not only by a stupid attempt to “jailbreak” the device, but also a malfunction of the gadget at the hardware level. Here are some of the hardware problems that can trigger the appearance of the “white apple”:

Breakdown of the power circuit. Such a breakdown is a consequence of a sharp voltage surge. In order to protect the gadget from power circuit malfunction, you should not put it on charge during a thunderstorm. Battery failure. You can extend the life of the battery if you use only original and high-quality chargers. Owners of old mobile devices are advised not to let the battery drain completely. Faulty motherboard. Such a breakdown does not immediately make itself felt. If with each launch of the iPhone the apple burns on the screen longer and longer, the user should take this as a symptom and start saving money for repairs.

The problem of the “white apple”, finally, may be due to the fact that the gadget is simply frozen. The Apple website has the following scale:

From this illustration, it is easy to understand that the manufacturer does not guarantee stable operation of the iPhone at temperatures below 32 ° Fahrenheit (which corresponds to 0 ° Celsius). If the smartphone is at a temperature of 4 ° Fahrenheit (-20 ° Celsius) for a long time, expect trouble.

How To Fix STUCK AT APPLE LOGO ENDLESS REBOOT Trick iOS 12 iPhone, iPod & iPad

The easiest way to get rid of the “white apple” caused by low ambient temperatures is to place the iPhone in a dry, warm place and leave it alone for at least 20 minutes.

If the problem of the “white apple” appeared after a failed jailbreak, you should not hang your nose. In this case, you can fix the problem with your own hands. by flashing your smartphone and removing previously downloaded tweaks from Cydia.

But if the “apple” “hangs” on the iPhone, which did not go through the jailbreak procedure, for the owner of the gadget it is a wake-up call. It is very likely that the iPhone refuses to turn on due to a hardware failure, to fix which you will have to contact the service.

Connecting the charger

If the screen does not light up, no matter what buttons you press, then the reason for this state may be a freeze iOS or a complete discharge of the battery. Problems with the level become especially relevant in winter: in the room the indicator can show an acceptable value, but as soon as you go out into the cold, the amount of charge drops sharply and the phone turns off. To turn it back on:

• Connect your phone to the power adapter.
• Wait 10-15 minutes and try to start the iPhone again.

If the battery is completely discharged, then 15 minutes may not be enough for it to have enough strength to turn on. But if you press the power key, you will see icons. battery, adapter and lightning. They signal that the smartphone is charging, which is very good.

If your phone won’t charge, make sure the charger is working properly. Be sure to check the cable connector. If it is dirty, the device will not charge. Also, use original accessories to avoid problems. A counterfeit charger can cause serious hardware damage, including damage to the power and charge controller.

Problems can also arise due to the failure of the battery. for example, it will simply exhaust the limit of charge-discharge cycles. It is impossible to replace the iPhone battery on your own without special equipment, so you just have to go to the service center.

Contacting the service center

If the iPhone does not turn on and does not respond to buttons in any way after connecting the charger, rebooting, and even restoring in DFU mode, then you do not need to experiment with it, trying to guess what is the cause of the malfunction. Problems can be very different, from mechanical damage to the charger socket to breakdown of controllers.

They can determine the exact cause at the service center, especially since they usually do not take money for a preliminary inspection. You don’t need to repair your iPhone yourself without special equipment and skills. Unskilled intervention in the operation of the device can lead to more serious malfunctions and make the cost of repairs even more expensive.

Do not forget to read the comments, there is also a lot of useful information. If there is no answer to your question, and there is an answer to later comments, then the answer to your question is contained in the article, respect someone else’s time.

Disconnecting iPhone during a call: finding and fixing the cause

IPhone turns on and off immediately: how to restore a smartphone

iPhone Won’t Turn On: Troubleshoot and Resolve the Crash

If your iPhone won’t turn on or respond to buttons, don’t rush to the service center. It is possible that the problem can be corrected by yourself, if there is any malfunction at all, and not just the battery is discharged.

Comments: 5

I rebooted my iPhone and the screen on my phone only works for 2-3 minutes and then does not work again.
help me please

Good afternoon, check the battery performance, charge. And in general, it’s better to go straight to the service.

Good evening, iPhone 5 is unresponsive. black screen and that’s it, the service could not understand the reason for what to do next, I don’t know

Good day! please tell me, the iPhone 5 has not been charged since 22:00 the previous day, it does not see charging (the screen is black) and does not turn on ((((what to do? this is correct?

What to do if the iPhone 5se was on charge, turned off and refuses to turn on, the home button does not work for me, so I can’t hold down the “home” button and “turn on” WHAT TO DO?

Hard reboot

If the iPhone does not boot, the apple is on, the first thing to do is try to restore the device to work by performing a hard reset. Hard Reset.

Press Home and Power (on iPhone 7 and 7 Plus, the volume down key is used instead of Home). Hold them until the device turns on. If a hard reboot does not lead to anything, move on to another method. System Restore.

iPhone does not load beyond apple (does not load). what to do?

One of the most unpleasant problems that happen with smartphones from Apple. the iPhone does not boot beyond the apple.

When you try to turn on the phone, the company logo appears on the screen, but the system does not start. The error can appear on any model: iPhone 5, iPhone 6, iPhone 7.

IPhone Recovery

The main disadvantage of restoring is deleting settings and content. If you recently made a backup, then the losses will be minimal, but still you cannot do without them. a working phone is more important. Since you are dealing with a software error, to fix it, you need to put the phone in DFU mode.

If the call does not go through, or you cannot find the files responsible for the error, then you will have to restore the iPhone to fix the problem.

iPhone does not turn on, lights up “apple” and goes out

A white “apple” glows on the screen either continuously, until the battery is discharged, or the device cyclically overloads every few minutes. This can happen for the following reasons:

A swollen battery will deform the device board. This malfunction is more typical for the third generation iPhone, where the battery is installed between the “trough”. the bottom of the case and the motherboard. Deformation of the board leads to breakdown of contacts and as a result the device “hangs” on the splash screen. After replacing the battery with a new one, normal operation of the device may or may not be restored. If we get lucky.

Deep discharge of the battery

The battery controller blocked as a result of an extreme discharge will not allow charging it by standard methods.

Therefore, to eliminate the problem, you will need to open the device, dismantle the battery, and check it. If the battery is in good condition, charge it with a universal charger. How to do this, let’s try to figure it out on the example of the third generation iPhone, since it is with them that the most work will be done.

• Removing the SIM card tray
• Using a screwdriver, unscrew the two screws, to the right and left of the cable connector.

Why the iPhone does not turn on: what to do when the apple is on and off

For the owner of an “apple” device, the biggest nuisance is an “apple” that is always glowing on the display or, in general, a “black screen”. The device entered an infinite boot cycle or does not turn on at all. Often this is a consequence of a malfunction of the motherboard of the gadget and only a service center can help.

So, let’s figure out what problems can be when the iPhone or iPad turns off by itself, why the apple burns and goes out on models 4, 4s, 5, 5s, 6, 6s, what to do in such cases.

How to fix problems

All faults are traditionally divided into hardware and software problems. To fix software errors, we need a USB cable and a computer.

For the treatment of iron, the list will be much wider:

The battery is out of order and needs to be replaced

If you do not contact the service center, the chances of purchasing an original battery for replacement are zero. When buying a battery, be sure to check it for leaks, swelling and corrosion. If possible, check the voltage with a tester.

Why iPhone won’t turn on: make a diagnosis

Outwardly similar symptoms can be the result of completely different malfunctions. Correct diagnosis. 90% success, so below we will analyze in detail the possible options for breakdowns.

The cable connector does not work

The cause of this malfunction may be either dirt in the connector or damage to the contacts in it. To fix the problem, you need to do the following:

• Using a syringe, moisten the connector liberally with alcohol and leave for a few minutes.
• Re-wet the connector and use a medium-hard brush or toothbrush to remove any dirt.

Checking the loops

Rarely enough, the cable of the screen or any other element inside the iPhone can jump out of the connector, as a result, the screen flickers for 5s, the apple lights up and the display goes out. It is easy to treat it, we open the phone case, and flip all the connectors with loops.

The flickering of the screen should disappear, along with it the problem should go away when an apple is on the screen of the iphone 5, but does not turn on.

It’s all about the battery

The most common and simple reason when an apple burns and the screen goes out on an iPhone. A person is sure that the phone is charged, and does not understand why it turns off immediately, starts looking for problems in other malfunctions. But everything is trite. the battery is out of order and needs to be changed or tried to calibrate. Will calibration help? It’s a moot point, it’s worth a try, that’s for sure.

To begin with, let’s try again to recharge the phone’s battery, but with the help of another charger, since the first one may simply be broken.

We remember if the iPhone turns on only before the apple and turns off immediately, first of all we try to change the memory, and only then we proceed to other, more radical methods.

Burned out microcircuit on the board

If even the flashing did not help when the iphone 4s, 5, 5s, 6, 7 models blinks with an apple on the screen and does not turn on at the same time, then the exact cause of the breakdown can be told exclusively at the service center. Most likely, the microcircuit on the motherboard of the smartphone burned out or went off, you cannot fix it yourself, you need expensive equipment.

In this case, he can only list the factors why this could happen.

• Falling iPhone into water, followed by a short circuit.
• The power controller came out of a standing position, after a strong voltage drop in the household network or using a non-original charger.
• Over time, the battery becomes unusable, after two or three years, the battery should be replaced in any case. Very rarely, the battery breaks down as a result of mechanical damage when dropped on a hard surface.
• The iPhone does not turn on while charging, the apple lights up and goes out, in this case, the damage may be hidden in the internal microcircuits. For example, the Flash memory chip has come off the board or disconnected as a result of a fall. The same can happen with any chips on the motherboard, be it NAND Flash or Nor Flash chips.

There are two ways out. to solder yourself, but if you are not friends with a soldering iron and do not have straight hands, it is better not to climb, you can simply kill the iPhone, without the possibility of recovery. The best option is to take the phone to trusted masters.

An apple is lit on the iPhone screen and it does not turn on, what to do?

Depending on the iPhone model, the screen may display a white screen with an apple or a black background, depending on the color of the case. The background does not matter, if the logo appears and the iOs download stops there, we follow the instructions. But first, let’s determine what happened to the phone.

Making a forced reboot

In 90% of cases, a hard reboot will remove most glitches and crashes when the iphone 5 smartphone flashes an apple on the screen and does not turn on.

• We disconnect the iPhone from the computer or laptop, since iTunes may interfere with the restart and switch the device to UDF mode, now we do not need it.
• We simultaneously hold down two Home and Power buttons, wait 5-10 seconds, the phone should go into reboot.

After rebooting, the logotype will appear again for a while, and after a minute you will see the loaded iOs, you can use the device in normal mode, and not try to install the crooked application that caused such problems. If the above methods did not help, then you will have to reflash the device.

Reflashing iPhone

It must be remembered that when flashing, all information is deleted, you will receive an absolutely clean phone with factory settings. Then you can restore everything, but provided that you have a saved backup in iTunes. In the absence of a backup copy, only an authorized service center will help to get information from the problem gadget, but for a decent price. Therefore, at least once a week, make a backup if you have important information on your iPhone.

How to reflash an iPhone was discussed in the article. If you don’t want to waste time reading, I’ll leave at the bottom a video instruction on how to reflash the device, if the iPhone 5 doesn’t turn on, the apple is on and after a while the screen goes out.

As a result, store your iPhone in a case and avoid dropping onto a hard surface, it will save you from a lot of problems and save a lot of money on repairs. But if this has already happened, we follow the tips and carefully watch the video instructions.

Equipment setup

Discharged battery

Banal utterly, but one of the most common reasons. The user is sure that the phone’s battery is charged, but it is almost completely discharged. Try plugging in your charger and after waiting 20 minutes, try turning your iPhone back on. By the way, this is also possible in the event of a charger malfunction. The user thinks that the device is charged, but he just finally sat down. Try charging from a computer via a USB cable.

iPhone won’t turn on and apple is on. what to do?!

Tablets and smartphones from Apple have long won the reputation of being fairly reliable devices. And the iOS operating system did not give any particular reason for criticism. Nevertheless, sometimes problems do happen. electronics, whatever one may say, are capricious thing. One of the frequent occurrences is that the iPhone does not turn on and the apple on the screen burns. On this, the phone freezes and you will not be able to turn it off in the usual way. There are quite a few probable reasons for the appearance of this trouble. Let’s try to figure them out and, if possible, try to fix it ourselves.

Blog about modems, routers and gpon ont terminals.

Software crash

If you have recently installed any application before, digging through the settings or tried to jailbreak, then with a high degree of probability we can say that this is exactly what causes a crash and the appearance of a glowing apple.
Very often the so-called “hard reset” helps. restarting the phone using the Home and Power buttons, which must be pressed and held for 8. 10 seconds. In more than half of such cases, the iPhone then boots up and works successfully. The main thing. do not forget to disconnect it from the computer or charger before that.
Did not help? Then you should try to reflash the device. To do this, you need to launch iTunes on your computer, and then connect your iPhone to your computer with a USB cable. then turn it off by holding the Home and Power buttons. You need to hold it until the screen goes out, after which you need to release the Power button, but do not release Home. This will put the iPhone in DFU mode. The screen will be black, but a message should appear on the computer that the device is in recovery mode. Let go of the “Home” button. In the iTunes application, click the “Restore” button, after which the process of downloading and installing the new firmware on the phone will begin.

After this procedure, you will receive a “clean” device, without settings and additional programs, and the burning apple on the iPhone should disappear.

Hardware problems

Unfortunately, the reasons why the iPhone does not turn on and the apple on the screen is lit are very often problems with the hardware stuffing of the phone. And then flash it. don’t flash it, but it won’t work anyway. What could be the reason?

Unfortunately, only those who are friendly with a soldering iron and a multimeter can fix this kind of malfunction with their own hands, the rest of the users can only take it to the service center for repair.

IOS Restore or Update via iTunes

ITunes. Apple’s media combine. is often viewed with distrust due to its button-cluttered interface and confusing navigation. In fact, the tool: it will help you filter both the entertainment media library, and will help with the recovery of a locked or non-working iPhone.

The only thing you have to deal with is downloading and installing the latest version of iTunes, and connecting your iPhone to your PC using a USB cable. Next. go to the parameters of mobile technology, presented in the “Overview” section.

It is advisable to prepare an up-to-date backup copy of the contents of the internal memory at the bottom of the interface before starting the procedure. Formally, no data can disappear when the iPhone is restored to work. But extra safety net won’t hurt. Backups are generated and stored: either on the hard drives of the computer, or in the iCloud cloud storage in the iOS settings.

Regardless of the choice, you will have to return to the top of the interface and click on the “Restore iPhone” button. iTunes will automatically download the update files and transfer the latest iOS version to mobile devices in the background. The procedure takes on average up to 30 minutes (this is due to the preparation and preliminary unpacking of files before updating or restoring). After several reboots, the problem with the “iPhone does not turn on, the apple is on and off” will disappear.

IPhone does not turn on (apple burns and goes out): from reasons to reset

Hello everyone! Today I ran into a problem. the iPhone does not turn on, the apple is on, and the smartphone itself just goes out. at first it seems to turn on, then it turns off and it goes out. And so constantly when you turn it on.

Apple mobile technology rarely encounters unsolvable technical problems and errors. But the problem with the iPhone not turning on or hanging on the apple logo has already become overgrown with legends and has become a widespread phenomenon. And that means it’s time to figure out the details and find out why the iPhone does not turn on, the apple burns and goes out, and how to save mobile equipment using iTunes.

Reset iOS settings

If the iPhone does not turn on periodically (out of 5 times, no more than 2-3 freezes on the Apple logo), then before contacting the service center and experimenting with the DFU mode, it will not hurt to roll back the operating system parameters to the “factory” state. The procedure will not take even 10 minutes, and even a backup copy will not be needed: the content stored in memory will not disappear anywhere.

Reset starts from “Settings”, menu “General”. The desired section is at the bottom of the list, right above the “Turn off” button.

After the transition from the actions that appear, it remains to select “Reset all settings”, enter the PIN code (verification via Touch ID or Face ID is not available) and wait until iOS clears the parameters and restarts the iPhone.

Often, a reset is already enough to get rid of freezes and technical problems when an apple blinks or the iPhone screen starts to blank out unexpectedly. But even more often, you can’t even look into the “Settings”. iOS doesn’t even load. Therefore, it’s time to move on to universal methods.

Reasons why the Apple logo is lit and the iPhone won’t turn on

• System crash caused by software problems or recent updates to the iOS operating system. In some situations, the problem also appears when interacting with unsupported characters. we are talking about hieroglyphs sent via iMessage, which on some versions of iOS lead to an emergency shutdown of the iPhone.
• Battery discharged or defective.
• The power adapter and charging cable are damaged and are not able to charge the iPhone even up to 5%, which is why the apple logo does not disappear.
• Mechanical damage: iPhone dropped and constantly reboots, remained under water for a long time, or lay for several hours in the sun or in the cold.

IPhone Recovery via Third Party Software

Unofficial software tools handle iOS problems like iTunes. And sometimes they offer even more: an intuitive interface, a predictable course of actions and recommendations for beginners.

The same diagnostic service ReiBoot, adapted for computers with Windows and MacOS, offers in a matter of moments:

• Run DFU mode without holding the buttons on the iPhone case, but through a special menu in the interface.
• Return to standard mode or go to a special section with “Support”. where tips appear for situations when an apple is on or mobile equipment does not respond to pressing.

It is easy to interact with ReiBoot: the developers first suggest connecting the iPhone to the computer using a cable, and then, in the interface that opens, select the “Enter recovery mode” item.

How you have to proceed further depends on the reason for the appearance of the non-disappearing logo and the version of the iPhone (4, 5S, 6, 6S, 7 or newer). But with a 99% probability, ReiBoot will first download the stable version of iOS from the official Apple servers (either new, or the current one, but “reset” to factory settings).

Then it will automatically start the update process. The procedure takes from 15 to 30 minutes, depending on the speed of the Internet, the amount of space occupied on the internal memory of the iPhone and the number of errors found in iOS.

Why iPhone 5s won’t turn on?

Press and hold the Power button and the Volume Down button on the left for 15-20 seconds, after which the Apple logo will appear on the screen. It is worth noting the situation with the freezing of some program, when pressing the buttons also does not help.

What to do if iPhone 5s is frozen on an apple?

Sometimes a forced restart of the device helps to get rid of an apple on a dark screen. iPhone 7 and newer models can be rebooted by simultaneously pressing and holding the power button and volume control for 10 seconds.

What to do if iPhone 5s won’t turn on while charging?

If iPhone charges but won’t turn on, restore it via DFU mode.

• Press the volume up button and release immediately;
• Press the volume down button and release immediately;
• Press the side button and wait for the branded apple to appear on the device display.

Why does the apple burn on the iPhone and does not turn on?

The main root cause of the problem, if an apple is on on the iPhone, the phone does not turn on, is a banal lack of energy for the smartphone, since the iPhone battery has a very low percentage of charge. In this case, after restarting the smartphone, it is quite possible to face such a situation.

How an apple glows on an iPhone?

Apple unveiled the iPhone 11 as the successor to last year’s iPhone XR in September. He received a new dual camera and slightly redesigned, including new body colors.

What to do if iPhone 8 is frozen on an apple?

Smartphone freezes on apple while loading

• On iPhone 8, 8 Plus, X, press and release the volume up button, then press and release the volume down button.
• If you are using an iPhone 7 or 7 Plus, press and hold the Power and Volume Down buttons for ten seconds or longer until the Apple logo.

After update

The problem may appear immediately after installing a new firmware version. What to do in this case? First, let’s try to update again. If this does not help, we try to return to the previous version, on which our iPhone felt fine. Download the required version from the manufacturer’s official resource. Until the moment of pressing the “Restore” button, hold down Shift. In this case, a list of file versions will be offered, from which we will choose the one that suits us.

If the buttons do not work

There is also the following option: the iPhone does not respond to button presses, and the screen of the last application is frozen on the screen. The first thing to do in this situation is to force restart the device. To do this, simultaneously hold down the “Sleep” / “Wake up” and “Home” buttons and after ten to fifteen seconds you will see that the apple is on the screen again.

It happens that the device still does not turn on. Then you should connect to the charger and leave the iPhone charging for fifty to sixty minutes. You will soon see that the charging screen is on. If this does not happen, check carefully the connector socket, charger and cable. Perhaps the reason is in them. Try the same procedure using a different source of battery power.

Hardware malfunction

But when none of the above scenarios helped, then with a high degree of probability you can look for the reason in the hardware. This can happen after moisture gets inside or the elements of the gadget naturally age. This is caused by non-original cords and cables, as well as failure of the connectors. In no case should you try to open the case with your own hands if you have no experience and knowledge of carrying out such work.

After drowning

Contact with any moisture is destructive for all electronic devices, including such complex ones as modern telephones. First of all, the contacts, as well as the conductive paths inside the case, oxidize and rust. It is best not to turn on the iPhone itself, but to contact the service center after drying. They will deal with the restoration of conductive paths on the motherboard, as well as contacts that have been badly damaged by oxidation.

The battery died

In addition to malfunctions with the charger, this is one of the most common reasons for a gadget not turning on. This is usually evidenced by its full discharge with up to 30% charge on the indicator or spontaneous termination of work in cold weather. In this case, the only way out will be a complete replacement of the battery: either from authorized dealers, or buying a high-quality copy. It is not worth letting him and discharging “to zero”, as this impairs his performance. Better to avoid discharging below 20% of maximum.

Burnt out charge controller

The so-called power controller can fail due to voltage surges, as well as poor quality of the charger. Often, moisture penetration into the device leads to the same ending. This is a certain microcircuit responsible for providing energy to all nodes of the smartphone. However, with such a breakdown, you must contact the service center.

Software malfunction

Even when exclusively proprietary programs and applications are used, unexpected “hangs” in their work may occur. This is not to mention how many utilities are downloaded from little-known and little-trusted sources. Problems with software often arise after errors in updates, after jailbreaking firmware, or running multiple applications at the same time. In these situations, you need to use the login through iTunes or try to turn on in other modes, if a hard reboot did not help.