Table of Contents

Why iPhone 7 won’t turn on

If it is the breakdown of the iPhone 7 that takes place, then several options are possible at once.

  • Damaged motherboard circuit and / or power connector. Such damage often occurs during the use of non-original accessories.
  • Due to contact with liquid or physical damage, the power button or battery does not work. This problem will be helped to solve in the service center.
  • Problems with the charger or power cable (smartphone cannot be charged). First, you need to make sure that the battery is charged and the charger is working properly: sometimes gadgets are brought to the workshops, which just have run out of battery. Batteries lose their charge at low temperatures, so a smartphone that has been operating in freezing temperatures simply needs to be charged. You can also inspect the charging connector. If dirty, clean carefully.
  • A software error occurred while updating. iPhone 7 sometimes turns off when you try to install new software on it. the gadget turns off spontaneously, and the usual way of turning it on does not work. This problem can occur due to the failure of the Nor Flash chip of the GSM module. This technology is responsible for configuring phone services for the SIM card of a cellular operator. Even with a successful attempt to turn on the gadget, it will be impossible to make voice calls.
  • Due to moisture ingress, oxides appeared on the motherboard. For repair, it is better to contact the master.

IPhone 7 hardware malfunctions usually require repair at a service center. Here you will need diagnostic equipment, tools, as well as special knowledge and experience.

iPhone 7 won’t turn on. possible problems and ways to solve them

Let’s look at the reasons why the iPhone 7 won’t turn on. Consider the possible causes of the breakdown and solutions to the problem. Often, you will need a professional iPhone 7 repair based on a service center. special equipment and experience are required. Contact our workshop in your city.

Is your iPhone 7 unresponsive to button presses on startup? This is not a cause for panic. For example, unlike the seventh model, the 7th procedure requires pressing the Power button and the volume down key located on the left side of the phone (pressing must be held simultaneously for 20 seconds). For iPhone 7, you will need to press the Power and Home button. As a result, the Apple logo appears on the screen.

Restoring iPhone 7 in Device Firmware Update Mode

If your smartphone does not respond to a restart, you can try to restore the system yourself through DFU mode. We are not responsible for your actions.

Important! Flashing via DFU will delete all data from iPhone.

  • iPhone 7 should be connected to the computer and run iTunes.
  • Next, the smartphone must be switched to DFU mode by holding down the Home and Power buttons at the same time and holding them for 10 seconds. While continuing to hold the Home button, release the Power button and hold the Home button for another 10 seconds (or until iTunes puts iPhone 7 into recovery mode).
  • In the iTunes window, select “Next”, “I Agree”, wait until the new version of iOS is loaded and the smartphone is restored.

If iTunes does not detect the iPhone, then the problem is most likely a hardware problem. To fix physical damage to iPhone 7, contact a service center.

iPhone Won’t Turn On After Discharging

And get the best deals from trusted masters.

  • Compare and choose the best conditions
  • Feedback from interested professionals only
  • Don’t waste time communicating with intermediaries

Everyone can face a situation where the iPhone is charging but not turning on. Perhaps the cause of the breakdown is serious, and you will have to repair your smartphone for money. However, in some cases (for example, if the connector is dirty or there is a software failure), you can fix the malfunction at home without having the experience, qualifications and tools. It is worth trying to find the problem yourself and restore the phone to work.

What are the causes of iPhone malfunctions

Many iPhone owners are experiencing difficulties: the gadget is slowly charging or does not turn on at all. And if a minor problem (for example, a breakdown of the Home button) is not so critical, then in such situations it is impossible to use the phone.

  • critical internal parts (tristar controller, sync loop, power controller, motherboard or battery) are damaged due to mechanical impact (shock, falls) or liquid flooding
  • a faulty, non-original charger is used (cheap Chinese fake)
  • breakage of the Lighting connector or its contamination caused by dust, hair, lint and other small debris
  • software failures (software directly affects the microcircuit that controls the charging process)
  • the USB port of the tablet or stationary computer is broken
  • factory defect of Apple components involved in the battery charging process

Errors during the operation of programs, breakdown of chargers and iPhone parts (batteries, connectors, cables, etc.) can manifest themselves in different ways. A few examples:

  • iPhone won’t turn on after being discharged (when the battery is low)
  • the application hangs, does not respond to taps, or the screen is completely black
  • the gadget turns on, but hangs after the Apple logo appears
  • the indicator is on, but the charge level is very low even for a long time
  • iPhone is dead and does not turn on when charging from a cigarette lighter or computer

Before taking your smartphone to a service center, make sure that the cause of the malfunction is a breakdown in the hardware. And in any case, do not postpone the trip or the call of the master if you spilled water on the iPhone. every hour of delay can aggravate the situation.

How to get your iPhone back on track

If you have problems with turning on and charging, first of all, check if there is current in the outlets. Next, if the phone does not turn on at all, connect it to the charger. In a normal state, the gadget immediately writes that it is charging. the indicator is on, which means the process is in progress. Remember that the battery is not designed to operate in low temperatures. Therefore, warm up the smartphone before connecting the charging, if the battery runs out in cold weather.

Another situation. you are trying to start an iPhone that has been discharged for a long time. If the battery goes to zero, you need to wait 15-60 minutes and only then press the Home or Power button.

The smartphone still does not respond. we perform a hard reboot:

  • press the power buttons and “Home” at the same time (for devices of the 7th generation. “Power” and the volume control button)
  • wait 10-20 seconds until the Apple logo appears on the screen of the gadget
  • release the buttons. the operating system will start in about one minute

This method also helps with other problems. For example, when the program hangs or there is no response to buttons.

When the Apple logo is on and off again, you need to restore. Most likely, the battery has run out due to a software failure. The error was caused by an unsuccessful iOS update or downloading and installing unlicensed software.

  • run iTunes on the computer and insert the USB cable into the connector
  • turn off your smartphone using a combination of the Home and Power buttons (if you have an iPhone 7, use the volume button instead of Power)
  • press the “Home” button and, while holding it, connect to the computer
  • hold Home until the phone screen starts showing the iTunes logo and plug icon
  • the computer display should display the message “There is a problem with your iPhone; it needs to be updated or restored “
  • confirm recovery

The procedure for downloading and installing the new version of iOS will take about 30-40 minutes. There is another recovery method. DFU mode. The method is radical, as it destroys all data on the phone. Stages:

  • connect the charger (the charge level must be greater than zero)
  • after five minutes, disconnect the charger, connect the smartphone to a computer (stationary or tablet) and turn on iTunes
  • simultaneously press Home and Power, hold them for exactly ten seconds, then release the on and off button
  • keep “Home” (15-30 seconds) until the notification in iTunes (when you enter DFU mode, nothing should be on the phone screen)

Then you should confirm the procedure and click on the “Restore” button. If you forgot to overwrite data from your phone, you can undo the restore: disconnect the USB cable, hold down Home and Power for 10 seconds. Then the iPhone will restart.

If everything is fine with the software, inspect the connector for contamination. The litter clogged in Lighting should be carefully removed using improvised means, for example, a toothpick.

When charging the battery from a computer, consider the functionality of the USB port. Possibly not enough amperage. try a regular Apple charger.

Pay attention to the charger itself. Even if the original Apple cables are fragile. the sheath and cores are easily damaged. what to expect from cheap Chinese products. The phone may stand for a long time and show charging, but it will still be zero if the charger is fake or broken. Use only original charger to avoid similar problems.

If the above actions were unsuccessful, most likely the battery discharge was due to normal wear and tear, factory defects or damage. If you dropped or flooded your phone. don’t even look at the indicator: take the gadget for repairs as soon as possible or call a specialist home.

iPhone is dead and won’t turn on anymore

Apple smartphones are characterized by high performance, functionality and a fairly powerful battery. For example, the iPhone X lasts more than 40 hours when listening to music, and more than two days in standby mode. Recently, however, more and more users have begun to notice that the iPhone is quickly discharging and heating up when charging. Many attribute this to the release of the new iOS 11 system, which consumes more power than its predecessors. You have to charge a gadget with a new operating system several times a day and additionally put it on charge for the whole night.

Sometimes it happens that the iPhone is completely discharged and does not turn on anymore, and there is no charging icon on the screen. The reasons for this may be:

  • faulty charging;
  • low throughput of the charger;
  • battery failure.

What to do?

Most importantly, do not panic and do not try to disassemble the device. First, check if the charger is working properly by connecting it to another smartphone. If the device is charging normally, then most likely it’s time to replace the iPhone battery. This can only be done in a service workshop, since the design of the Apple smartphone is non-separable.

If, when the charger is connected, a battery icon appears on the screen, but the gadget does not charge or turn on, the reason may be iOS freezing. This happens when the battery is deeply discharged. To fix this problem, charge the device for 6-8 hours and then try turning it on. If the smartphone starts successfully, observe how long it holds the battery charge.

Another way to turn on iPhone is DFU recovery. To do this, you need to connect your phone to your computer, go to iTunes and click the “restore” button. In most cases, this procedure will help turn on the device.

READ  How to download an app on an iPhone

If all the above methods did not help, contact the service center for diagnostics. Free diagnostics at rem-iPhone centers.

iphone, turn

? Remember how a forced reboot is performed on your device. It can help with most of these crashes that can happen on the iPhone.

A forced reboot is completely safe. Its execution does not delete any data on the iPhone, so you can perform it safely.

❗ Methods to restore iPhone in this tutorial are arranged from easy to hard. If a hard reboot doesn’t work, go to the next method. He will have to help solve the problem.

Connect iPhone to charger

Often the iPhone won’t turn on and show no signs of life due to the fact that its battery is dead. Connect your smartphone to the charger and leave it connected for an hour.

Here are some important tips to keep in mind:

  • Use original or quality charging accessories. There have been cases in which the iPhone turned off due to a dead battery, but did not charge due to using a broken charging adapter or cable. Be sure to check that the charger and cable are in working order.
  • Charge iPhone with electricity. It is very common for users to charge their iPhone from a computer USB port. But due to the old battery in the smartphone and the low power of the connector, charging simply does not occur.
  • Check if the connector is dirty. Sometimes iPhone won’t start charging due to a heavily soiled Lightning connector. Examine the charging port. If it is really dirty, clean it gently, for example with a toothpick.

⚡ How to understand that the iPhone has started charging?

If the battery logo with the Lightning cable is on the screen. iPhone does not charge and asks to connect to the charger. If this logo is displayed after you put the iPhone on charge, then the cable or adapter is out of order. Use other charging accessories.

If only the battery is displayed on the screen, then charging is successful. It is worth worrying only if this logo is displayed unchanged for more than 30 minutes. In this case, you should also replace the charging adapter and cable.

Restore iPhone via iTunes

If the iPhone does not turn on even after connecting to the computer, then only recovery will help out.

❗ In most cases, recovery involves deleting all data from the device. You can return them only if you have an up-to-date backup.

Connect iPhone to computer with USB cable and launch iTunes (Finder window in macOS Catalina).

Enter iPhone into recovery mode. For this:

Note: iPhone must be connected to computer via USB cable.

  • On iPhone 6s, iPhone 6, iPhone 5s, and earlier. Press the Home and Power buttons (power button, located on the side or top of the case) at the same time for about 20 seconds until the iTunes logo appears on the screen (laptop logo in iOS 13).
  • On iPhone 7 and iPhone 7 Plus. Press and hold the Volume Down and Power (Side) buttons at the same time for about 20 seconds until the iTunes logo (laptop logo in iOS 13) appears.
  • On iPhone 8/8 Plus, iPhone X and later. Press and immediately release the volume up button. Press and immediately release the volume down button. Then hold down the side button and hold it for about 20 seconds until the iTunes logo appears (laptop logo in iOS 13).

iTunes will report detecting iPhone in recovery mode. In the window that opens, select “Update”. Initially, this option should be selected, as it can allow you to return the device to a working state without losing data.

If data lossless recovery is possible, the iPhone update process will start. Wait for it to end. ❗ Never disconnect your iPhone from your computer.

If the update fails, then a recovery should be performed. Re-enter iPhone into recovery mode (step) and in the iTunes window that opens, select “Recover”. Wait for the end of the operation.

Updating or restoring will bring your iPhone back to working condition.

Perform a hard reboot

The first thing to do if the iPhone won’t turn on is to force it (aka “hard”) restart. It takes the iPhone out of recovery mode, which may have been accidentally turned on, and simply resets software errors on the device.

Iphone 7, 7, 8, 8, x black screen unresponsive, dead, won’t power on, quick and easy.

Force restarting works differently on different iPhone models.

On iPhone 6s, iPhone 6, iPhone 5s, and earlier. Press the Home and Power buttons (Power button, located on the side or top of the case) at the same time for 15 seconds until the Apple logo appears on the screen.

On iPhone 7 and iPhone 7 Plus. Press and hold the Volume Down and Power (Side) buttons at the same time for 15 seconds until the Apple logo appears.

On iPhone 8/8 Plus, iPhone X and later. Press and immediately release the volume up button. Press and immediately release the volume down button. Then hold down the side button and hold it for 15 seconds until the Apple logo appears.

iPhone won’t turn on, black screen. what to do

iPhone won’t turn on and apple is on? Or is the screen completely black and the iPhone is unresponsive to button presses? Both of these problems can happen to any iPhone user without dropping the smartphone. Learn what to do if your iPhone won’t turn on in this tutorial. You can solve the problem without going to the service center and the accompanying expenses.

Connect iPhone to iTunes in Recovery Mode

If the iPhone does not respond to either charging or hard restarting, the smartphone must be put into recovery mode. Here we immediately note that you may not need to directly restore the iPhone. Everything in order.

The first step is to try to get your iPhone back in working order without restoring it. This method has saved thousands of iPhones without erasing data, which implies recovery. Therefore, we strongly recommend that you initially use it.

Connect iPhone to computer with USB cable and launch iTunes (Finder window in macOS Catalina).

Enter iPhone into recovery mode. For this:

Note: iPhone must be connected to computer via USB cable.

  • On iPhone 6s, iPhone 6, iPhone 5s, and earlier. Press the Home and Power buttons (power button, located on the side or top of the case) at the same time for about 20 seconds until the iTunes logo appears on the screen (laptop logo in iOS 13).
  • On iPhone 7 and iPhone 7 Plus. Press and hold the Volume Down and Power (Side) buttons at the same time for about 20 seconds until the iTunes logo (laptop logo in iOS 13) appears.
  • On iPhone 8/8 Plus, iPhone X and later. Press and immediately release the volume up button. Press and immediately release the volume down button. Then hold down the side button and hold it for about 20 seconds until the iTunes logo appears (laptop logo in iOS 13).

In the iTunes window, click “Eject iPhone”.

Restart your iPhone. To do this, simply hold down the Power button (side button). Alternatively, you can perform a forced reboot using the method described above.

As a result of this operation, your iPhone can turn on and work again as before without the need to restore.

If all else fails

None of the above methods helped? This means that your iPhone has a physical breakdown and you need to contact a service center.

Why iPhone won’t turn on?

A failed battery is the most common reason iPhone stops turning on. If you previously noticed that the smartphone was rapidly discharged, turned off by 10-30% of the charge, turned off in the cold and any other similar anomalies happened to it, then the problem is definitely with the battery.

Replacement will help. expensive in Apple authorized service centers in Russia. 3000-7000 thousand rubles.

Failure of the power controller is another very common cause of iPhone failure. Symptoms before a smartphone fails are similar to a battery breakdown. accidental disconnections of the device, overheating.

Replacement is relatively inexpensive. You can change the power controller or other microcircuit associated with the charging process for about 2,000 rubles.

Failure of other components. iPhone may not turn on due to the breakdown of dozens of different components, including the motherboard. Most often this happens after the fall of the smartphone. It is possible to determine what exactly broke down only during the diagnosis.

Renovations can be ruinous. If the iPhone didn’t overheat before it broke, then it’s best to start praying right away that the motherboard is intact. Replacing it, especially on newer iPhone models, will cost a pretty penny.

Before going to the service center, we recommend that you contact Apple official support. The company’s specialists will be happy to help with advice.

When component replacement is required?

Problems with the mechanical part are considered more serious. These include: the phone does not start due to a breakdown of the power controller; the battery does not charge due to a malfunction of the charge controller; error of the NAND memory module on which all information is stored.

If the iPhone does not turn on due to mechanical problems, it is better to contact a workshop with this. An attempt to save money on repairs usually ends badly: you still have to pay, but more, in the worst case, you will need to buy a new gadget. Many of the symptoms are similar. Only high-quality diagnostics will help to find the cause, and professional intervention will eliminate it without a trace.

IPhone 7 plus won’t turn on: what you can do yourself?

Put the gadget on charge, but he is silent? The situation with the fact that the iPhone does not turn on is familiar to many users. The reason is often cited as being hit or falling into the water; an unsuccessful update also ends with a black screen. Before contacting a service center, you can try to reanimate the phone in simple ways. If they do not help, then we go to the service for qualified help.

We deal with the causes of breakdowns

The reasons for the failure of technology are divided into mechanical and systemic. Why won’t the iPhone turn on if the bull’s-eye is on the screen? Such a malfunction usually occurs after an unsuccessful firmware. The update could have gone wrong, errors prevent the system from starting. The problem often arises from the cable. Outwardly, it can be completely intact, but inside it is damaged. To exclude this possibility, we take a new (only original) cable, repeat the firmware procedure. If there is no result, then we look for the problem further.

The second most common problem for iPhone won’t turn on is charging. First of all, we recommend checking the charger, inspecting the wire. The ideal option is to use the new charger, which should only be from the manufacturer Apple. Having eliminated this problem, we check the battery. The need for replacement can be judged by the following signs: spots appear on the screen; the percentage of the charge changes spontaneously; the battery discharges quickly; the battery is swollen.

Any of these symptoms is a reason to urgently consult a master. A feature of the iPhone is the built-in battery. In order not to break the fastening, the repair should be entrusted to a professional.

If the lace icon and the iTunes inscription may appear on the screen during the firmware update, it is possible that the Internet connection was interrupted or there is not enough memory during the update. First, you need to try to restart the phone by holding down the Home and Power buttons for 15 seconds at the same time. The gadget should restart. If the error repeats, we bring it to the service.

Than water or falling threatens?

The telephone has become an indispensable assistant in everyday life. Not surprisingly, the likelihood of dropping or spilling liquid is very high. At the same time, many users are frivolous about moisture inside the phone. Experience shows that three hours are enough for serious damage to occur. If you do not contact the service in time, the chances of a successful recovery decrease dramatically.

The result of hitting a hard surface is the appearance of cracks on the glass, scratches, dents on the case, a black screen. Why iPhone won’t turn on after impact, what should I do? Mechanical impact very rarely passes without consequences. Considering that the inside is hidden from our eyes, it is possible to ignore some malfunctions for a long time: fragments of the display damage the Wi-Fi antenna; microcracks appear on the motherboard; soldering is broken; the liquid gradually oxidizes the contacts.

Diagnostics will help to identify them. Having carefully studied the current condition of all components, the master will give an opinion on the possibility of repair, replacement of parts or batteries. There are many reasons why the iPhone does not turn on even without visible external damage. Given the high cost of the gadget and its complex internal structure, we advise you to entrust the clarification of the circumstances to professionals. Inexperienced actions only exacerbate the problem, lead to an increase in the cost of repair.

Force reboot

The prompt solution to the problem is to restart the smartphone. To do this, hold down the Home and Power buttons with your fingers, then wait 10 seconds. When the specified time has passed, the smartphone logo will appear on the screen. The gadget will turn on, then connect the charger to the socket and wait for the battery to charge.

READ  How to make a book on iPhone

Power on problem after operating system update procedure

We decided to update the firmware, but it was unsuccessful. After that, charging does not work, the screen does not light up, the smartphone does not turn on.

Power supply problem

Sometimes the smartphone refuses to turn on and charge due to a problem with internal components. The reason may be a battery that has sat down forever, a power controller, breaks in the loop contacts, breakdown of other elements on the motherboard. In this situation, complete disassembly and repair will help, we carry it to the service center. It is not worth eliminating the cause on your own, there is a high chance of causing additional damage.

Reasons iPhone 7 won’t turn on or charge

A common situation is that an expensive iPhone 7 does not turn on and does not respond to charging in any way. Users in this situation panic, but do not be afraid. It is possible that the iPhone 7 does not turn on and does not respond to charging for simple reasons that the owner can quickly fix.

  • mechanical damage,
  • power failures,
  • difficulties with updating the operating system.

Now a little more about why the iPhone 7 does not turn on.

Mechanical deformation

The first reason is mechanical failure. People charge their smartphone carelessly, use it while charging, which is wrong. Gradually the connector wears out, the contacts are erased, and it becomes problematic to charge the iPhone. The charging cable is frayed, from such manipulations the gadget also stops working. Sometimes a button on a smartphone fails and the gadget no longer turns on. The reason for such damage is the careless attitude of the owner of the smartphone.

IPhone 7 won’t turn on

If the iPhone 7 does not turn on, and the connection to the charger does not work, do not despair, it will be possible to repair it. Today we’ll tell you what to do if your iPhone won’t turn on.

what to do if your Apple iphone 7 or 7 plus won’t turn on

Apple smartphones are reliable devices, but they also break down periodically. In 90 percent of cases, the fault is the user who treated the gadget carelessly. In other situations, this is a manufacturing defect. Let’s talk about what to do when iPhone 7 won’t turn on.

Charger connection

Some iPhone owners save on the purchase of chargers. And it is not surprising. the originals are not that cheap, and a similar model is easily purchased on Aliexpress. Problems of this kind with accessories are common. so connect your phone to the original charger and see what happens.

Recovery using DFU mode

DFU-mode. a special mode of operation of iOS, which is used to update and restore gadgets. If an emergency occurs when the smartphone cannot update, use this method. If your iPhone 7 Plus won’t turn on, you need to do the following:

  • run iTunes on your computer;
  • connect your smartphone to a PC using a proprietary cable;
  • turn off the gadget by pressing the power button;
  • while holding this key, press also the volume down button for 10 seconds;
  • then release the power button, wait 5 seconds.

iTunes will notify you when your smartphone is connected. Now click the “Restore” button in iTunes, wait until the operating system starts.

In case of difficulties, try manually selecting and installing the previously downloaded firmware. To do this, go to iTunes using the above method and select recovery while holding down the Shift key. Now select the firmware file and confirm your choice.

Sometimes the Apple gadget refuses to enter DFU mode. This can be understood by a number of signs:

  • the company logo is lit on the screen;
  • the iTunes icon flashed on the display (the phone is in Recovery Mode, there are no items you were looking for).
  • iTunes does not see the connected smartphone.

If you observe such symptoms, try repeating the procedure for switching to DFU mode. After the restoration is complete, the phone will return to normal state by itself.

What to do if the iPhone 7 turns on before the apple and turns off

If an apple blinks on iPhone 7, it means the device cannot find the iOS system. What to do?

Apply recovery to update. Recovery mode, considered a last resort or emergency solution, is well known for solving complex problems.

So, if none of the above solutions worked, give him a chance to sort out the mess himself.

Much can be restored, but any data on the local device that has not been backed up will be permanently lost.

First, connect iPhone 7 to PC and open iTunes. When it’s connected to iTunes, hold the side and volume down buttons together. Detailed instructions with dirks here.

Keeping them pressed even after the Apple logo appears until you see the recovery mode screen.

When the recovery mode screen appears, release the buttons. It will then ask you if you want to update or restore your device.

Select Update to fix the problem without deleting the content. If you want to erase all existing content and settings, select “Restore”.

iPhone 7 shuts down and does not force restart

A forced restart is always your first step when trying to revive a lifeless iPhone 7. Talking too much about the fact that it is completely discharged and does not turn on (sat down).

If your screen is black or the display is frozen, a forced restart or hard reset can provide a seemingly miraculous solution.

To start doing this, press and hold the side button and make it quieter for at least 10 seconds (until you see the logo)

often than not, this will fix common problems such as freezing and crashing. So never miss an opportunity to give it a try when you run into unexpected problems. If the forced restart does not help, it is recommended to connect the phone for at least an hour to allow it to turn on.

A drained battery will discharge deeply and can sometimes lead to some random quirks, and an hour on charge can make things work again.

Just before moving on to other cases, letting the phone charge, make sure the connection is good.

First, wait a few minutes to see if the battery charging screen appears.

If so, just let it charge for a while. If you don’t see the charging icon or your phone won’t start, it’s time to take a few more steps.

Replace charger and cable and try a different set the power supply may not work.

Also, also make sure the Lightning port is clean and free of debris. You can use a toothpick or a small hand pump with compressed air to remove lint or debris.

iPhone 7 turned off and won’t turn on while charging or apple is on

Who would not ask why the iPhone 7 7 plus does not turn on, even if there is the best apple specialist, you will not get an answer, even if this is a new phone and after a complete discharge.

Why? Because there are many reasons. Of course, if it falls down and does not turn on, then the reason is clear as a white day. After the fall, only repairs.

Many other reasons can be eliminated by yourself, but you think you understand that if, for example, the memory burns out, and this can happen when the apple is on, and the iPhone 7 does not turn on, then there are no other solutions besides replacing the memory.

Just don’t be in a hurry. The memory burns very rarely and in most cases the problem can be solved. This is even better than a black screen, since then the backlight of the screen may burn out, and such a repair will cost you a lot.

Although the screen does not turn on on the iPhone 7 very often for a trivial reason due to a low battery or a sudden software crash that can prevent loading.

Just don’t be discouraged. I will give you a hint what to do, as there are quite a few viable solutions that can fix an iPhone 7 or 7 Plus that has stopped turning on.

Let’s try the fixes to get it back to normal. Software glitches can be easily fixed by a forced reboot.

iPhone 7 turns on and off keeps restarting

The very first thing you need to do and get your smartphone back into work is to perform a hard reset.

If that doesn’t help, connect it to the charger and leave it on for a while. If nothing works, restore in recovery mode.

over, contacting a reputable repair center would also be a great idea if nothing helps you.

There are enough reasons, but if the apple is hanging, then the problem is definitely not related to screen damage, but most often a software failure.

There is another good trick that I forgot about, this is a computer program specially for such purposes.

I will not present it here, since there is already a ready-made record with a detailed description, and now I just have to wish you good luck.

IPhone won’t turn on. what to do?

The iPhone, like any complex electronic device, can break down, shut down on its own, and fail to execute commands. IPhone turned off and won’t turn on? To find out the reasons for any malfunctions, it is necessary to show it to a specialist and make a professional diagnosis. You can, of course, try to enable it yourself, using “Google for help”.

For starters, don’t panic. Faults can be hardware and software. You can try to cope with software problems yourself.

The main reasons why the iPhone does not turn on:

  • the phone was in the cold for a long time, or the battery was completely discharged. Let the iPhone “warm up” and charge;
  • the smartphone was flooded, dropped, or it was repaired by a “left” master. At this point, how lucky, the diagnostics in the service center will show;
  • manufacturing defects. Rarely, but it does happen. In this case, a specialist examination is also needed. For warranty repairs, there is no need to look for an authorized service center, you can contact the Apple SC
  • Software crash. Disruption of any software or iOS itself. Solved without phone repair costs.

How to “resuscitate” if the iPhone does not turn on

These little tricks are to restart the device. The reboot failed, which means it should be connected to a power source for an hour. Did not work out. The last attempt is to reanimate the smartphone using iTunes.

Use DFU mode to restore your smartphone

  • Connect to home computer and launch iTunes.
  • To switch to DFU mode, simultaneously press “Home” and “Power”. After ten seconds, the “Power” button can be released. We hold “Home” until the iTunes sign and the plug appear on the display. In the program window, it remains to confirm the iPhone recovery procedure. This process will take about an hour, at least forty minutes. An uninterrupted internet connection is required for the software to download normally.

If all this is difficult for you or you have not achieved the result, contact the competent masters. Welcome to Apple Service Center! Experts will deal with the problem of your iPhone in a maximum of half an hour!

iPhone frozen and won’t turn off or restart

Usually, if the iPhone freezes, users try to turn it off or restart using the standard procedure, namely by long pressing the Power / Lock button. Unfortunately, in most cases, when the iPhone freezes, this shutdown method does not work. iPhone keeps running and running frozen applications no matter how long the user presses the power button.

But, the iPhone has an alternative shutdown method that bypasses the iOS operating system. Thanks to this, this shutdown method works even on tightly frozen devices. The method consists in simultaneously pressing the Home button and the Power / Lock button.

The Home and Power buttons must be pressed simultaneously and held until the frozen iPhone turns off. After turning off, you need to wait a few seconds and make a short single press on the power button. After that, the iPhone will turn on and start working normally.

It should be noted that the key combination “Home Power on” is also responsible for taking a screenshot. But, to get a screenshot on these keys, you need to press literally for 1 second, if you hold the keys longer, then the anti-freeze protection will work and the iPhone will reboot.

If you have an iPhone X or newer, then you need to use the new reboot method.

What to do if iPhone is frozen

Freezing is a problem that any computer technician faces. At some point, one of the programs begins to behave incorrectly or conflicts with another program, and as a result, the entire device is inoperative. This situation is called freezing.

iPhone is also prone to this issue and may freeze from time to time. Usually, when the iPhone freezes, it refuses to turn off or restart, which confuses the user. Most often old models freeze, such as iPhone 4, 4s, 5, 5s and 6. But sometimes even iPhone 6s and 7 users face freezes.

If you find yourself in such a situation, then this material should help you, here you will learn what to do if your iPhone is frozen.

iPhone 7 / 7 Plus: How to Fix Black Screen/ Wont Turn On/ Blank Display

iPhone freezes when turned on

Pressing the Power On Home buttons at the same time allows you to turn the device off and on in any situation. However, this procedure does not guarantee that the iPhone will not freeze again during the startup process.

If your iPhone freezes before the device is fully loaded, then you can use the recovery mode called “Recovery Mode”. With it, you can restore your iPhone to its original state and bring it back to life. But, it should be borne in mind that this procedure is equivalent to a factory reset and leads to the deletion of all user data.

READ  How to lock the camera on iPhone

In order to enter Recovery Mode on iPhone and perform recovery, you need to do the following:

  • Turn off your iPhone and wait a couple of minutes for all programs to finish their work. If the iPhone does not turn off in the standard way, then you can resort to the combination “Home Turn on” described above.
  • Then you need to press the “Home” button and without releasing it, connect the iPhone to the computer via the Lightning cable.
  • Once connected, continue to hold the Home button until the iTunes logo and cable image appears on the iPhone.
  • Now you need to release the Home button and start iTunes on your computer.
  • In the iTunes program, you need to go to the iPhone settings and click on the “Restore iPhone” button.

Thus, you can solve the problem with the iPhone freezing during startup, but, as already mentioned, for this you will need to donate all user files. You can read more about Recovery Mode in our article on resetting iPad to factory settings.

Also, Apple devices have a so-called DFU mode or Device Firmware Update. If recovery mode does not help, then you can try to enter iPhone into DFU mode and try recovery again.

iphone, turn

Force restart if iPhone won’t turn on

If iPhone won’t turn on after iOS 12 update. We recommend performing a forced reboot. It is done differently depending on the model of your iPhone.

So, for example, to make a forced restart on an iPhone 8 or iPhone 8 Plus, then follow these steps:

  • Step 1: Press and quickly release the Volume Up button.
  • Step 2 Press and quickly release the Volume Down button.
  • Step 3: Press and hold the power button until the company logo appears on the screen. Hold the power button for a few seconds until the “Swipe to turn off” slider appears

To force restart iPhone 7 and iPhone 7 Plus, you need to do the following:

  • Step 1: press the power button and the lock button without releasing them.
  • Step 2: press the volume button.
  • Step 3: Hold these buttons until the screen turns off and the logo appears.

If you have an iPhone 6S, then you need to follow these steps:

  • Step 1: Press the Home and Power buttons at the same time.
  • Step 2: wait about 7 seconds.
  • Step 3: Your screen should go blank and the Apple logo icon should appear.

Check your cloud storage if iPhone X / 8/7/6 / 5s won’t turn on

Oftentimes, iPhones have disk errors due to insufficient memory and lack of external storage options. It is highly recommended that you check the available memory before installing iOS 12. To install the new version of iOS 12, you need 4 GB of free space.

  • 1. Go to “Settings”.
  • 2. Open the “General” tab.
  • 3. Open “iPhone Storage”.
  • 4. Follow the directions to unload apps or upload your entire library to iCloud.

If your iPhone doesn’t have enough memory, we have Tenorshare iCareFone to transfer music, photos, videos, contacts, SMS without limits. It is a tool to create backup and restore data selectively and instantly.

What to do if iPhone won’t turn on after iOS 12 update

This year, Apple developers made us happy with the release of iOS 12. For now, the beta version is available to users, which is in free use. The release version will be presented in September 2018. The beta version, as a rule, is intended for developers in order to check the functionality of the system and get information about the work. as well as about its improvements. But as with many beta versions, the installs experience errors that disable the operation of the iPhone. For example, an apple is on, the iPhone does not turn on. iPhone is frozen. In this article, we will analyze all the effective ways to restore iPhone operation after iOS 12 update.

Reliable tool. if iPhone won’t turn on after iOS 12 update

If your iPhone won’t turn on after iOS 12 update, then Tenorshare ReiBoot is the ultimate solution for you. This tool offers a 1-click solution for such problems (iPhone won’t turn on, iPhone stuck on apple, iPhone doesn’t work, black screen on iPhone but it works, etc.) that occur in iPhone, iPad and all Apple devices Here are the steps to follow if your iPhone has turned off and won’t turn on.

  • 1. Download, install and run the program on the computer, connect the iPhone using the original cable.
  • 2.Click the “Solve All iOS Freezes” button in the main window to enter System Restore.
  • 3.Click on Fix Operating System. This will put the device into recovery mode.
  • 4. Download the latest firmware package by clicking “Next”. After downloading the firmware, click “Start Repair” and restore the system. This process takes less than 10 minutes, you cannot turn off the device in this process.
  • When the recovery process completes, your iPhone will automatically restart and there will be no more error on iPhone.

Restoring iPhone with iTunes after iOS 12 Update

iTunes can help you with these situations. You can always use iTunes to enter recovery / DFU mode and fix the problems. For example iPhone freezes, black screen on iPhone but it works. sensor or microphone does not work on iOS 12. You can restore your device using iTunes. If your phone is still working, you must sync your data first.

  • Connect iPhone to the computer that was syncing and open iTunes.
  • Wait while iTunes syncs iPhone and backs up.
  • Once the backup process is complete, click “Restore iPhone”.
  • When in the course of restoring iPhone, the setup screen should open, where you need to click “Restore from a copy of iTunes”. After that, you need to select your own device in iTunes. Look at the creation date and size of each backup and choose the one that suits you best.

If you have never synced your iPhone with iTunes, I will note that this method always works, but all media files and information will be erased on the iPhone. Connect your iOS device to your computer and open iTunes, make a forced restart, select “Restore”.

It is worth noting that this method takes a long time and has a low success rate or the iPhone does not turn on and does not work at all.We recommend using Tenorshare Reiboot to restore iPhone / iPad / iPod.

Ways to fix the problem. iPhone turned off and won’t turn on

Important: Check if there are hardware issues with your iPhone

If none of the above solutions helps, chances are that you are experiencing a hardware failure. Broken screen or loose connection can also lead to iPhone hardware issue. Also, if you’ve replaced your damaged hardware with an unauthorized one, such as your screen, the new update may not support your device. Therefore, you need to contact your nearest Apple Service Center.

IPhone 4, 5, 6, or 7 won’t turn on. power adapter

A fairly common problem that the iPhone 5s does not turn on is a power failure situation. The user, even when connected, may not see any reaction of the smartphone, but often they do not even suspect about such a banal solution to the problem as charging.

The iPhone owner needs to connect it to a charger, no matter what power source: 220 V network, car or computer. Do not be alarmed if there is no immediate reaction. With deep discharge, for example, when the phone freezes, it takes time for the charging indicator to appear. It is worth waiting at least a few minutes, usually this time is sufficient. It is better to put it on charge for 1 hour, and then try to turn it on, do not forget about the previous method, it is applicable now. Sometimes the process does not start, this can provoke various mechanical problems.

  • Check the cleanliness of the connectors, remove all kinds of foreign objects and dirt with a needle or brush;
  • Make sure that there are no kinks in the wire, probably there are interruptions;
  • Check the tightness of the contacts, the wire may not enter completely, then you will have to determine the reason for this;
  • We strongly recommend using original chargers. Lightning cables from Chinese manufacturers overheat during operation, may have insufficient power to charge or practically no power;
  • Sometimes the power or charging controller fails, then you will have to use the services of a service center.

What to do if iPhone won’t turn on?

The iPhone is not an eternal device, although it breaks down a little less often than Android, but still it is not uncommon, then the question arises of what to do if the iPhone does not turn on. Gadgets often break down, freeze and stop responding to user actions. Often the reason is mechanical or external damage to the device, but this is not always the case.

Why iPhone won’t turn on?

It is not worth thinking about why the iPhone 5 and any other model does not turn on for a long time if it was externally exposed to unwanted influences:

  • Perhaps the smartphone was dropped into the water, even a short-term immersion or rain can provoke a short circuit and refusal to work. If the phone was really drowned, you should not turn it on right away, on the contrary, turn it off and put it off to dry. After 1 day, try to turn it on, so the probability of restoring its work is higher, otherwise a short circuit will occur at startup and the smartphone will be unusable;
  • Mechanical damage. An iPhone, falling from a height, often takes a hit on the display, and the insides are less likely to suffer. There is no way out except to give the smartphone for repair;
  • Freezing. Batteries are afraid of prolonged exposure to frost, and at one point they lose all their charge due to a chemical reaction. You need to warm it up in your hands and then try to start it, most likely you will have to charge it.

In these cases, it is possible to eliminate the malfunction only at service centers. There are a number of other reasons that lead to a freeze, some of which can be easily removed.

iPhone Shut Down and Won’t Turn On. Force Start

If the iPhone 5s has turned off and does not turn on, you should use the function that forces the smartphone to start. The method is relevant for those cases when the smartphone is frozen at some stage, perhaps only a black screen is shown, but the backlight is working, or after turning off, the phone stops turning on. In this case, the procedure does not clear the device data, so it should be used initially. For each version of the iPhone, there is the same key combination, only in the latest 7th model it is different:

  • Hold down the Home button and the Power button at the same time. The hold time should be more than 10 seconds, usually up to 20 seconds. Then the Apple logo appears on the screen in the form of an apple. This option works for all versions except iPhone 7;
  • A separate, more familiar approach is used in the new version, you need to hold Power and the volume control, namely the volume down button. Similarly, you need to hold until the action on the screen begins.

The problem can be fixed by this method, but there are several additional methods.

How to turn on iPhone if it won’t turn on?

It happens that the iPhone charges, but does not turn on, especially often it reaches the logo and freezes at this moment or turns off. In this case, you can apply recovery mode. To use it, you need to have a computer at hand. It is highly desirable that the iPhone has already been connected to it beforehand, and the PC has been added to a trusted source of the connection, but this may not be useful.

  • Connect your smartphone and computer;
  • Launch iTunes;
  • Perform a forced restart of the device. Home (for the 7th version, the volume down button) and Power;
  • A message will appear on the computer screen allowing you to restore the operation of the iOS system, you should click on “Update”.

In this case, an attempt will be made to install the operating system without erasing the files. You may need to completely restore your iPhone to factory settings. Then in iTunes you will have to go to the main tab and click “Restore”.

Ultimately, if iPhone 6, iPhone 7, or any other version still won’t turn on, you need to contact technical support. They will remotely provide instructions on how to fix the problem, if this does not help, then they will direct you to the service center closest to you. This will mean that the problem is of a technical nature and the user is powerless here.

If the smartphone was used with care and charged with original chargers, then most likely it will be possible to restore its operation using the described methods. Otherwise, you will have to give the device to experts.

No votes yet! Be the first to rate this post.

BYRGPUB.COM 2021