iPhone is dead and won’t turn on. what to do?

Recently a friend asked for help. Said that his iPhone is dead and won’t turn on while charging. What to do in a similar situation? Personally, I am a fan of the Android operating system, so I went to the Internet for answers. I “dug up” several ways that can help, but not always. Now let’s look at the instructions for the iPhone.

If iPhone is dead and won’t charge. what to do?

Based on the listed factors, we will consider effective solutions.

• When the battery is completely exhausted, connect the original “charger” to the iPhone, connect it to the mains and wait about fifteen minutes. At first, the screen will be black, but later an icon should appear indicating the start of the process:

Suddenly Afyon 6 does not start even after half an hour, but a “hint” appears on the display. they say you need to connect to the outlet, then do the required operation and wait at least four hours until the resource is 100% restored:

• If there is a software-type failure (the methods listed above are powerless), then you will have to resort to a “hard reset”. Hard Reset is simple, but after it all installed applications, data are deleted, that is, you get an iPhone with a clean firmware.

It is necessary to hold down and hold two buttons on the case. Home and Power (inclusion). If you have a new iPhone that doesn’t have a Home control, then hold down Volume instead:

Do not release until the display shows “bull’s-eye”. This usually happens in twenty seconds. The first start after the reset will take longer than usual, you will have to wait. And then immediately put it on charge, after which you can restore information from iCloud.

Common problem

Judging by the messages on the forums, such a negative phenomenon is rare, but it does take place. And this must be somehow dealt with. It is good that in the overwhelming majority of cases you can do without going to a service workshop. This means you can save a lot of money (yes, repairing the iPhone 7 and other models is not cheap).

Why won’t my Apple smartphone turn on after plugging in the power adapter? The reasons are as follows:

• The device was in a discharged state for a long time (from several days or more);
• A software failure has occurred;
• The charging socket is damaged, or there is another hardware failure preventing the phone from being powered up.

If it doesn’t help

I don’t want to upset you, but if the listed solutions to the problem are ineffective, most likely the reason is a hardware failure:

• The battery is completely dead. it will need to be replaced at a service center;
• Charging cable damaged. try using a different one;
• The slot for connecting the power supply is broken. you will have to contact the SC to replace the connector;
• Critical failure of the base “firmware”. alas, you won’t do anything at home.

Now you know what to do if the iPhone is dead and does not turn on even when the charger is connected. Try it and be sure to write in the comments which method was useful for you.

iPhone Won’t Charge: Why and What to Do

The situation when the iPhone stopped charging can happen for several different reasons, which we will try to determine ourselves today.

So, it will turn out to find out why the problem started at all and, if possible, eliminate it. In some cases, even no action is required from the user.

In the past, you learned how to charge your iPhone correctly. Now we will look at what to do when the iPhone does not charge or turn on, while charging may be working properly.

1 Reason. system

If the phone does not charge or shows an incorrect charge level, then first of all turn off the iPhone and turn it on again. This will ensure that the problem is not with the system.

Always, first of all, turn off and turn on the device first. It really helps when the iPhone just starts to glitch.

iPhone is charging slowly

Often, after a system update, the first few charges of the phone are very slow. The system calibrates the battery, within a day or two everything is normalized.

This can also be the case when you charge it over the Lightning cable via USB 2.0. The problem is either the port or the cable. You can try plugging it into USB 3.0.

After 80%, iPhone always charges slower. This is a built-in battery calibration function. Disabled in the battery status settings, the item is called “Optimized charging”.

According to the developers, the function should generally adapt to the user and only turn on charging after 80% when the iPhone is normally charging. In fact, it just charges more slowly after 80%.

2 Reason. charger

One of the most common reasons. original / non-original charging is out of order, does not charge, the phone is heating or heating up.

In this case, try plugging the Lightning cable into any USB port of a computer, laptop or even a TV to check if charging has started.

How To Fix iPhone 7 or 7 Plus That Won’t Charge

8 Reason. controller or port

If even after changing the battery there are problems with charging, incorrect values ​​are shown, it does not work at all, then the power controller is very likely broken. It needs to be replaced, to find out for sure you will be helped in any service.

In case of any mechanical damage, in any case, it is always better to contact the service center, since, with such problems, only there will be able to name the reason.

4 Reason. USB port or socket

Quite often, when connecting an iPhone or other device via USB to a Windows 10 computer, the USB port may simply stop working. To fix the problem. restart your PC or insert your smartphone into a different port. Additionally, you can try another outlet, but this is quite a rarity.

If charging does not come from USB at all, then try connecting the lanyard to the charger. There is more tension and the process can go.

iPhone Won’t Charge. Hardware Reasons

The reasons iPhone won’t charge but shows it charging are as follows:

• Damage (breakage) of the cable. If your cable has been damaged (physical wear and tear, animals, children, etc.) then you will not be able to charge your iPhone, and in some cases you will see signs of charging, but de facto it will not happen;
• Broken charging port (Lightning). Usually caused by physical wear and tear, as well as strong (sharp) movements of the user when connecting and disconnecting the cable;
• Port clogged with dirt. In the process of long-term use of the phone, staying it on various fleecy (dirty) surfaces, the jack can become clogged with small pieces of wool, dirt, dust, and others, which leads to insufficient contact of the cable plug with the port;

• Charger problem. For some reason (physical wear or incomplete compliance with the declared characteristics) your device does not give the declared charging parameters (usually 5V and 1A), and this leads to various problems with charging the smartphone. This is especially true for devices from little-known manufacturers (the so-called “noname”);
• Battery problem (usually wear and tear). Over time, the battery depletes its life and needs to be replaced. If you have been using your iPhone for a long time, or purchased it from your hands, then it is likely that the battery of your device has exhausted its resource;

• Physical damage to the phone board. If your phone received any physical damage, fell or experienced any other mechanical stress, then it is quite possible that they adversely affected its functionality, including the ability to charge it;
• Problems in the controller responsible for charging the phone.

How to fix iPhone charging issue

So, if you have a situation that your iPhone is not charging, but shows that it is charging, then do the following:

• Try to completely discharge your device and then charge it;
• Hard reset your device. Hold down the On / Off and Home buttons with the device turned on, and hold until the screen turns off and the Apple logo appears on it again (it may take 30 seconds). After rebooting, try charging your smartphone again;
• Try using your cable with a different iPhone. If charging still does not occur, replace the cable;
• If, when the cable connected to the port moves, the charging turns on and off. it is quite possible that the port does not contact or is simply broken. Replace the port at the service center;
• Unplug your phone, take a wooden toothpick and gently pick up any debris that has accumulated in the socket. Do the procedure as gently and carefully as possible so as not to damage the contacts. Under no circumstances use any material that is highly conductive (for example, a metal pin), you can short-circuit the contacts and harm your device;
• Try your charger with a different iPhone. If charging still does not occur, replace (repair) the charger;

• Recover via iTunes. Connect your iPhone to iTunes on your computer, click on “Device” on the top left, then click on “Backup” and wait until the procedure is complete. Then click on Restore and wait for the process to complete;
• Check the charge controller (or the bottom cable) at the service center. If your iPhone doesn‘t charge, loses power quickly, gets very hot, then this may be an indicator of the controller’s “guilt”. If the controller is out of order, repair (replace) it;
• Replace the battery. If you have been using the phone for a long time, the battery may have worn out. Replace it.
• Contact the nearest service center, perhaps a significant breakdown of the board of your smartphone due to any accidental physical impact.

iPhone won’t charge but shows it is charging. what to do

Some of the iPhone users may face a situation where, when the charger is connected, their smartphone simply does not charge, and the culprits for this dysfunction may be the reasons for both hardware and software levels. In this article, I will tell you what to do if the iPhone does not charge, but shows that it is charging, I will describe the causes of this problem and the features of the methods for solving it.

iPhone Won’t Charge. Software Reasons

Among the reasons why it is impossible to charge the iPhone, there are software reasons, and some experts call them prevailing. The main software reason is a software malfunction (at the level of the smartphone’s firmware), which for some reason does not give commands to the phone’s controller to charge, therefore charging simply does not occur.

Also, the reason why the iPhone refuses to charge is the user using an incorrect (custom) firmware in his device (similar firmware is available for versions of the first generation iPhone, iPhone 3G and 3GS, iPhone 4, iPhone 4Rev A).

Check if the battery is worn out

If all of the above methods don’t work, a possible reason the iPhone won’t charge could be battery wear. IPhone battery is warranted for a year. After the expiration of this period, the battery remains operational for several more years.

If the smartphone battery has served its purpose, only replacing the battery at a service center will help, depending on the model.

Make sure there is no software glitch

Let’s move on to one of the most common reasons why you can’t charge your iPhone. If attempts to connect the device to a different port or adapter, or replace the charging cable are unsuccessful, the problem may lie in the phone software.

The fact is that inside the device there is a controller, which is a microcircuit on the board. The controller is responsible for charging the battery and operates under software guidance. If you connect the iPhone to a charger, voltage will be applied first to the board with the controller, and only then to the battery. If the software is in a frozen state, it will not give a command to the controller to start charging.

This problem can be solved by hard restarting the smartphone. To do this, simultaneously hold down the “Home” and “Power” buttons for at least 30 seconds.

What to do if iPhone won’t charge?

The iPhone may not charge for completely different reasons: from cable malfunction and mechanical damage to software failure and malfunction of device components. Below is a step-by-step guide. what to do if the device has stopped charging.

Watch a video on what to do if your iPhone won’t charge:

Find out if there is a problem with iPhone components

The rarest reason iPhone won’t charge is due to a malfunction of the internal components of the device. For example, the power or charging controller may fail. If the problem lies in the microcircuit, the situation is solved quite simply: replacing the chip with a new one in the service center. Such a procedure will not cause any particular difficulties for good specialists and will cost about three thousand rubles.

The power controller can fail if you frequently connect the device to uncertified chargers (for example, car chargers or cheap analogs of the original cable). The bottom cable may also be responsible for charging problems. It can fail as a result of mechanical damage. In any case, only high-quality diagnostics will help to determine the problem with the internal components.

How to tell if your iPhone has stopped charging?

When iPhone is charging properly, a lightning bolt icon appears next to the battery icon in the status bar, and a large battery icon also appears on the lock screen. If, when the charging cable is connected, charging does not start, or visually charging is in progress, but the phone does not charge at the same time, these are signs of a problem.

Check power supply

First of all, you need to check the power source. Often, the problem may lie not in a malfunction of the device or cable itself, but trite in a non-working outlet.

If the iPhone stops charging from the laptop, you must first complete all the processes that consume energy on the smartphone: for example, close applications, turn off Wi-Fi. However, charging the iPhone from a computer is, in principle, not recommended, since the USB interface was created for the exchange of data, and not for the transfer of energy.

Get iPhone out of “full discharge”

If the iPhone runs out of power and refuses to turn on after that, you need to follow these steps:

• Hold down the “Power” and “Home” buttons for at least 10 seconds.
• Release keys when the Apple logo appears on the display.
• Wait until the operating system is fully loaded.
• Turn on and off silent mode if the smartphone has not booted.
• Repeat the above steps until the result is achieved.

What to do if iPhone won’t charge but shows the opposite?

Although Apple’s technology is considered one of the most reliable on the market, it can still give users unpleasant surprises. One of the most common problems among iPhone enthusiasts is the loss of the device’s ability to replenish battery power. Let’s figure out why the iPhone won’t charge, and what to do about it.

Why iPhone won’t turn on or charge?

First, the iPhone shutdown may be due to some kind of software glitch. Most often, software freezes appear as a result of the device not having enough RAM to process all running applications. To fix this, in most cases, it is enough to hard reset the iPhone.

Secondly, on the iPhone, very often, as a result of mechanical impact or falling, the battery can come off the body of the device. If this happens, then at first the device may even work, and the user simply hears the characteristic sound of a dangling battery inside the case. Ultimately, in most of these situations, the battery cable connecting the battery and the board is frayed or torn. After that, naturally, the iPhone won’t turn on anymore. The solution to this problem is to replace the iPhone battery, which can be done at our service center.

The battery can also fail as a result of the use of low-quality chargers, power surges in the electrical circuit or moisture. In such cases, in addition to the battery one, the lower connector (charger connector) may also be damaged, which can also be restored or changed in the conditions of the service center.

But there are times when, as a result of mechanical stress, a short circuit or the use of low-quality accessories for charging the iPhone, the microcircuits on the processor board fail. The first thing that can get hurt. this is the Q2 microcircuit, which is a kind of fuse key for other elements along the power supply circuit of the board.

Following it, the U2 microcircuit (charge controller and USB synchronization microcircuit) may fail. If the situation is really bad, then the main power controller of the iPhone may fail, the damage of which, according to statistics, is one of the most serious problems associated with the power of the iPhone. Along with this, the microcircuit of the power controller of the modem part may also fail. The characteristic signs of this malfunction are the constant indication of the search for the cellular network, even without a SIM card inserted inside the device.

What to do if iPhone won’t turn on or charge

Every iPhone user sooner or later may face a serious problem, which manifests itself in the fact that the iPhone does not turn on and does not charge. It is worth noting that this can happen to absolutely any iPhone, be it the “old” iPhone 5, as well as newer models of iPhone 6s, iPhone 7 and even iPhone 8. Why does this happen and what to do. about this in detail

What to do if iPhone won’t turn on or charge?

Solving such problems is a more laborious process than conventional modular repairs, because working with a processor board and BGA chips always requires more time, effort and money. In addition, carrying out such an iPhone repair requires a lot of experience and knowledge of how the device’s motherboard works.

It is worth noting that such problems, when the iPhone does not turn on and does not charge, can appear for any user with any iPhone model. However, all iPhone power problems can always be resolved in our service center.

Therefore, we always advise you to entrust the repair of your iPhone and iPad only to trusted companies that are ready to have extensive experience and thoroughly understand the specifics of Apple devices. Please contact us. our masters will be happy to help you repair your iPhone!