What to do if the iPad does not turn on and does not charge, but the battery is burning

If the iPad does not turn on, then the problem can be looned in a low battery charge level. Deep discharge often leads to the fact that tablet computers do not turn on at all or turn off one or two minutes after the start. Therefore, the first thing you have to do in the situation has been created. put the tablet for charging and leave it alone for several hours. During this time, the battery charges, and you can try to enable iPad re most likely, a new attempt is crowned with success.

You charged iPad, but it turned out that it does not turn on again? In this case, you need to check the performance of the charger. It may not give the desired charging current, preventing normal battery charging. If you leave the iPad on a long charge, then with a broken charger, it will not give any effect. To check the performance of the memory, use another tablet or iPhone. You can also experience another charger on your tablet or try to recharge yourself from the USB port of your computer.

If you are sure that just a few hours ago, the battery was full, put your tablet on charging anyway. it is possible that during these few hours the battery is completely discharged.

Problems with the charge of the device

It happens that the iPad does not turn on, only a block of discharged battery is burning, requiring connection to a power source. The solution would seem obvious. Charge the tablet, and what to do if this does not happen even after connecting to the power grid? In this case, almost with a 100% probability can be told about a faulty charger that must be replaced. Otherwise, the problem can be buried in the port (to check for sure, you can buy an inexpensive Chinese wire, at least once it will work and give it to understand, in order of port or faulty), which will not be able to replace, as it is part of the motherboard. And its replacement. This is a very expensive repair, and it is difficult to find such a detail (a gadget donor is required). Therefore, if your iPad 2 does not turn on, think about updating the device. Probably, this tablet in your possession is not the first year, and it is much easier to part with him than to repaired.

In some cases, the iPad does not turn on, even when recharging and the tablet does not complain about the lack of connecting to the power supply. The problem can be burned in the device’s battery, it is damaged and also requires replacement (often this problem is accompanied by “blur” when you press the display with yellow spots in the corners of the screen, sometimes even drinking from the housing with glass). It is unlikely to replace it yourself, this time-consuming process and requires a certain skill, therefore it is better to turn to experienced specialists.

See also  How to return to factory settings for Samsung

If you have iPhone 8, iPhone 8 plus, iPhone X, iPhone XS, iPhone XS Max, iPhone XR, iPhone SE (2020), iPhone 11, iPhone 11 Pro, iPhone 11 Pro Max, iPhone 12, iPhone 12 Mini, iPhone 12 Pro, iPhone 12 Pro Max, iPhone 13, iPhone 13 Mini, iPhone 13 Pro or iPhone 13 Pro Max

Click and quickly release the volume button. Click and quickly release the volume reduction button. Then press and hold the side button until Apple‘s logo appears.

Other reasons and their decision

In addition to the reasons mentioned, such problems can be noted with which the iPad owner is most often faced:

  • Hacking OS (jailbreak) and the installation of unlicensed software. any interventions in the original firmware lead to numerous problems capable of fully removing the device;
  • The hardware breakdown of the button. sometimes the reason lies in faulty contacts that are under the tablet button, it is sufficient to replace them;
  • Mechanical damage. if the tablet fell or subjected to other mechanical damage, it is necessary to attribute it to the service center for a complete hardware check;
  • Charger malfunction. if charging was damaged, the tablet will not charge correctly and may not be included due to the discharged battery;
  • moisture inside the device. if earlier the tablet was exposed to water, due to its ingress, some contacts could oxidize and fail, in which case cleaning is required;
  • Short circuit. this can occur due to the use of faulty charging or strong drops on the network, and requires replacing all burnt elements.

Since any problems with Apple devices are recommended to solve through the Support Service of the brand, the user can do a little. If the reboot and recovery through iTunes does not help, it is impossible to solve the problem independently because it will exclude the warranty.

Most often, any malfunctions with the charge of Apple tablets are associated with custom-inattentive, since the devices of this brand are sufficiently resistant to any software and hardware failures. But it happens that the cause becomes incorrect operation of the iPad, and in such cases it is necessary to contact Support on the website of the digging or in the certified service center.

iPad does not turn on and does not charge

What to do if the iPad does not turn on and does not charge? Such situations arise not very often, but identify the cause of such behavior. The problem may be related:

ipad, does, turn, battery, apple

  • With a general malfunction of the device. it will have to be taken to the nearest service center;
  • With a malfunction of the battery. this is another reason to visit the service, as the batteries are changing only here;
  • With a malfunction of a charger or cable. check the integrity of these accessories and buy them to replace (in case of malfunction).

Thus, at home we can only perform the last operation. check the cable and charger.

See also  Vestel TV How to turn on AV without a remote control

Check the performance of the outlet and adapter

If everything is in order with the cable, and the iPad is not charging, then it is necessary to continue the search for the causes causing breakdown. Sometimes she can be so banal that sometimes it becomes very funny. The fact is that in its reviews, users often describe situations when a non-working outlet was used to charge the gadget. In order to exclude it, you need to connect another device through it that is in a working condition.

A bit more difficult is the case with the adapter. If there is an opportunity, then you need to try it on your smartphone or other tablet. You can also disassemble the adapter in order to visually check the status of the contacts.

Software faults and electronic components

Sometimes there are problems with the inclusion of the device and its charging, due to errors in the installed software.

Failures in firmware or application work

The most characteristic of this group are the following:

  • Apple logo appears on the gadget display, but when you click on the POWER key, the device does not turn on. In this case, it is necessary:
  • Conduct a forced reboot by simultaneously pressing the HOME and POWER keys;
  • If the problem has not disappeared, update the device software;

ipad, does, turn, battery, apple

If your smartphone is hung, and Apple‘s logo appeared on the screen, it makes sense to update the firmware of the device

If the empty battery icon appears on the screen, then the phone will soon turn on

If the screen shows the characters of the electric fork and the arrow, which indicates zipper, then the battery discharged completely and requires restoring its capacity

It is impossible for a long time to throw a gadget in a discharged state. This is not the best way reflected on the capacity of the battery. With timely recharge, the battery life is extended to the nominal value.

When repair and accessing service center is required

With mechanical damage or failure of the electronic diagram of the gadget, it is categorically not recommended to carry out the repair independently or attract an amateur specialist. This is especially true of products that are on warranty service.

In such cases, it is necessary to immediately contact a specialized service center. Specialists of the service tend to carry out free diagnostics and offer repair or under warranty or at a reasonable price.

Repairs in the service center must be carried out in the following cases:

  • failure of the power controller;
  • Cleaning the connecting loop on the main board of the device;
  • full battery life generation;
  • mechanical disposition damage;
  • Damage to USB-connector;
  • malfunction of the power adapter;
  • damage or breaking the power cable;
  • The failure of the electronic device elements.

Common causes and methods of struggle

If the iPad does not turn on, the first thing to do is put it for charging. In fact, this is the most common cause. The fact is that, in normal conditions, you see the level of charge of the device right on the screen, but if the battery is discharged completely, the device will not even be able to start to inform you about it. In this situation, you need to connect the charger (of course, knowingly working), and wait a few minutes. On the screen, after the primary charging of the battery to a state when the iPad can turn on, nothing will be, but an image of a discharged battery will appear on its completion. Let him fill the charge, and, after that, the tablet can be turned on. Actually, you can do it immediately as soon as you see this icon, but it is not recommended to do this. If this option worked for you, then you are lucky. Is that a few days should be supervised to the battery. if she degraded from time to time and keeps badly charge, you may have to contact an authorized service center for its replacement.

See also  Rear view camera Renault Laguna 3

How to enable iPad if it is not discharged, but still does not respond to buttons. a little different matter. It is possible that it is caused by banal freezing, and then a forced reboot can help. Tighten the power and “home” button at the same time for 10-15 seconds. Apple logo should appear on the screen. This command, bypassing the level of the operating system, turns off and includes a device. Action occurs at the iron level; In this case, the user data stored in the device’s memory, on the shaped hard disk (if you operate with familiar computer terms), but those that were stored in RAM, that is, the data running at the time of rebooting applications will be.

Such an operation can solve most problems arising from iPad. The fact is that most of the program errors are treated with the notorious “turn off and enable”, since this illudive algorithm restarts the execution of the program, and at the same time, the conditions for the occurrence of an error may not be repeated. But, you need to understand that not every error is treated in such a simple way. Let’s say if the iPad does not turn on, which is caused by a damaged system file, make such a reboot meaningless. Each time the operating system is launched, it will request this file and turn off with the same error.

Then will help restore the system through iTunes. This universal software allows you to spend many actions with your device, among them there are both we need in this situation. Connect iPad to a computer using a wire. Then, when running the program, clamp the “Home” keys and power on, but keep longer than in the previous case. 20-25 seconds. Apple logo will appear on the screen, which will change the system recovery symbol. At the same time, a pop-up window will appear in iTunes with the request, what to do with your iPad: Restore or update. Click on the “Update” button, it will start the procedure for reinstalling the operating system while saving your user data. Now it remains only to wait for the end of work.

If the process takes more than 15 minutes, iPad (like iPad 2) goes into sleep mode and does not turn on. What to do in this situation, we have already described: just repeat the same actions without turning off the device from the computer. Performing an interrupted task will continue from the previous place, since the iPad saves the system status in sleep mode.

BYRGPUB.COM 2022