Interface and indicators

IP Camera Recording Setup

1. Ethernet. connect to the network using an Ethernet cable.

2. Reset button. press and hold this button for 10 seconds to reset the settings to factory defaults.

3. Power connector. for connecting the supplied DC 5V power adapter.

4. I / O connector. for connecting external devices.

5. Locking ring. Tighten or Loosen the ring to adjust the position of the universal camera.

6. Holes in the stand. through the holes you can pass cables and secure the camera to a flat surface.

7. Lens. Performs Delight

8. Status indicator. displays the current status.

9. Microphone. performs sound recording.

10. Audio port. for connecting external speakers.

11. MicroSD card slot. MicroSD card is used to store snapshots.

Network storage

Fill in the following fields:

  • Network storage location. the path to the network resource.
  • Workgroup. the name of the workgroup.
  • User name. login to access the network resource.
  • Password. password for access.
  • Primary WINS server. WINS server address (optional).

Click the Test button to check the server availability and correctness of the entered data.

If we receive a Test OK message, then the settings are entered correctly and you can save them by clicking the Save Settings button.

Checking and saving data of the created server

  • After the server has been added, click the Add button in the RECORDING section.

Add recording settings window

Fill in the following fields:

Recording entry name. information field Recording name.

Enable this recording. enable / disable recording.

Priority. setting the priority for this event. Higher priority event will be executed first.

Source. stream source, you can set one of the profiles configured in advance.

Recording schedule. schedule. Here we mark the days and time range when you need to record.

Destination is the destination. In the drop-down menu, select the SAMBA server (SAMBA), which we created earlier.

Total cycling recording size. the amount of space allocated for the saved. With this parameter you set how many IP-cameras can take up space in the recording directory. After reaching the set volume, the camera will start erasing old files.

The camera overwrite aLGorithm works as follows: the camera is guided by the space of the hard disk that is occupied by the user.

Size of each file for recording. limiting the file size by the selected volume.

Time of each file for recording. limiting the duration of the created file by the selected time.

File Name Prefix. adding a prefix at the beginning of the file name.

Save setting window

Next, click the Save settings button to save the current settings. If all moods are correct, then continuous recording will be performed immediately on the specified server.

Posted by admin on August 24, 2019 August 24, 2019

Universal IP-camera D-Link DCS-2103 is the optimal solution for home and small office. Unlike a standard web camera, the DCS-2103 model is a turnkey solution with an embedded processor and web server, which transfers high-quality images for security and surveillance.

Easy setup and intuitive web interface provide easy Ethernet integration. The camera also supports remote control and motion detection functions for a cost effective solution to keep your home and office safe.

This model supports the Plug-n-Play function, which allows Windows computers to automatically recognize the camera and add it to the network.

By subscribing to one of the free DDNS servers, you can assign a domain name. This will allow you to use remote access, and not knowing its IP address.

D-Link DCS-2103. universal IP-camera

D-ViewCam D-Link software allows you to view images from 32 cameras at once on the screen of one computer. You can set up automatic email notification for instant information on abnormal events.

Below are the main specifications, LED descrIPtions and camera interface. Step-by-step guide to setting up recording on samba server.

At the end of the article Firmware and instructions in Russian are presented.

Standard settings:

Default IP address: 192.168.0.20
Login: admin
Default password: no

RTSP. stream:

Rtsp url: // IP address of the device /1.Sdp, where1.Sdp. 1 stream.

D-Link DCS-2103. IP-camera: setting up recording on Samba server

D-Link DCS-2103. setting up recording on a samba server

Preset the folder on the network device where the recording will be made. It can be a regular PC in the local network, but a ping must pass from this device to our camera. Give access rights to the created folder. Create, if not already created, a workgroup, username and password for this particular IP-camera.

For instance:

  • Working group: Workgroup;
  • Username: user;
  • Password: 123456.

Let the path to our folder look like this: \\ 192.168.0.100 \ REC \ 2103. Where 192.168.0.100 is the IP-address of the network device.

Open a Web browser (Internet Explorer) and enter the IP address of the D-Link camera in the address bar. Hit enter.

The username for the administrator account is admin. Enter the administrator password in the corresponding fields (no password by default). Click OK.

D-Link DCS-2103. password entry window

  • Go to the Setup tab.
  • From the menu on the left, select Event Setup.
  • To set up persistent recording, you need 2 sections: SERVER and RECORDING.

Server and Recording

  • Click the Add button in the SERVER section.
  • Enter any server name in the Server Name field and select the server to configure the recording: Network storage.

D-Link DCS-2103 Specifications

The main

  • 1/4 “Megapixel Progressive Scan CMOS Sensor.
  • Minimum illumination 1.0 lux.
  • 10x digital zoom.
  • Built-in 3.45mm fixed focal length lens.
  • Aperture F2.0.
  • Viewing angle:

57.8. horizontally;

37.8. vertically;

66. diagonally.

Functional

  • Motion detection windows.
  • 3 private masks.
  • Adjusting image quality, size and bit rate.

Compression

  • H.264 / MPEG4 / MJPEG.
  • JPEG for still frames.

Resolution

  • 16: 9. 1280 × 800, 1280 × 720, 800 x 450, 640 x 360, 480 x 270, 320 x 176, 176 x 144 @ 30fps.
  • 4: 3. 1024 x 768, 800 x 600, 640 x 480, 480 x 360, 320 x 240, 176 x 144 @ 30fps.

External interfaces

  • Micro SD card slot.
  • Built-in microphone.

Network protocols

  • IPv4, TCP / IP, UDP, ICMP, DHCP Client, NTP Client (D-Link), DNS Client, DDNS Client (D-Link), SMTP Client, FTP Client, HTTP / HTTPS, Samba Client, PPPoE, UPnP Port Forwarding. RTP / RTSP / RTCP, IP filtering, 3GPP, IGMP, ONVIF.

Safety

  • Protecting the administrator account and user group.
  • Password Authentication.

Event management

  • Motion Detection.
  • Event notification and download of snapshots / clIPs via HTTP, SMPT or FTP.
  • Supports multIPle HTTP, SMPT and FTP servers.
READ  How To Check The Rear View Camera On TV

Division 600.

Attention!
Before turning on the camera, make sure that the external Wi-Fi antenna is securely attached to the corresponding connector on the device. Turning on the camera without an antenna installed may damage the device.

To control the device via a mobile application, you need to make the initial settings. For this:
1. Connect your mobile device to a 2.4GHz wireless network.

Attention!
For the device to work correctly, the wireless settings must meet the following conditions:
The Hide network identifier (SSID) function is disabled
The encryption method used is WPA_P5K / WPA2_PSK
Dynamic network address assignment (DHCP) function activated
The access point name must contain only Latin characters

3. Start the DIGMA SmartLife application. Follow the on-screen prompts to complete the account registration procedure (for new users) or log in with your existing account details.

4. Go to the My devices / My group section. Click the “” icon in the upper right corner to add a device and select the device type Smart Camera. In the window that opens, click the button for selecting the setup wizard in the upper right corner and select one of the configuration methods supported by the camera: QR code (recommended) or Quick setup (if the Recommended method did not work).

5. Put the device into configuration mode by long pressing the on / off button (you will hear a confirmation beep, then voice prompts Reset to factory settings and Requires network connection “).

6. Follow the instructions of the setup wizard on the screen of the mobile device:

Make sure your mobile device is connected to a compatible Wi-Fi network and enter the password
Click Continue / Next Step and follow the instructions of the wizard
After finishing the connection to the network, give the device a suitable name and complete the setup.

After completing the setup, the camera is ready for use and will appear in the list of connected devices on the main screen of the application in the My devices section.

To view the camera image, click on the line with the camera name on the main screen. A preview window will open. The following controls are available in this window:

1. Date / time stamp

2. Advanced menu button

3. Wi-Fi signal strength indicator

4. Enabling audio channel listening

5. View quality switch

6. Switch to full screen mode

7. Switch between online and recorded

8. Quick setup of motion detection

9. Activating the talkback function

10. Pan and tilt control

11. Movie recording

12. Screenshot

For cameras with a rotating mechanism

Available FUNCTIONS

Internet control
Remotely connect to the device, control the current situation or view the recorded fragments from anywhere in the world where there is Internet, via the DIGMA SmartLife mobile application.

Motion Detector
Receive a notification on your mobile phone when motion is detected in the camera’s field of view, we activate recording when a motion detector is triggered.

Shared access
Share access in the camera, let trusted persons View the image from the device.

Night mode
In low light conditions, the camera will automatically switch to night mode by activating the infrared light.

Memory card recording
Turn on continuous recording, or activate it when events occur, view the recorded fragments from the mobile application.

ScrIPting support
Set up automation scrIPts and automatically perform different actions when triggered events occur.

Two-way voice communication
Activate the voice function by simply pressing a key in the mobile application.

Compatible with Android and iOS OS
Free app for smartphones and tablets DIGMA SmartLife is available for Android OS (version 5.0 and higher) and iOS (version 9 and higher)

INTRODUCTION

Purpose of the product
Household IP Camera Division 600 is designed for remote monitoring outside and inside the premises. The device has the function of remote control via the Internet using the DIGMA SmartLife mobile application.

SPECIFICATIONS

Image sensor
Sensor type: 1 / 2.7 “CMOS sensor
Resolution: 1920 x 1080 pixels FHD
Lens
Lens type: Full glass
Lens: 3.6mm
Viewing angle: 75
Day / Night Mode: Dual Infrared Filter
Working distance in night mode: 8-10 m
Wireless connection
Wi-Fi IEEE 802.11 b / g / n (2.4 GHz, 150 Mbps (Max))
wired connection
Supported Network Type / Connector: RJ45
Audio
Built-in microphone and speaker
Audio compression format: AAC ® G711
Main functions
Image compression format: H.264
Resolution: 1080p
Frame rate: 15 fps
TF card recording
TF card slot (up to 32GB)
Mobile application for iOS and Android
Motion Sensor
Dust and water protection class: IP63
general
Powered by AC adapter
Compatible with IPhone and Android devices
Size: 132 x 65 x 65mm
Device weight: 332g

Larger card support is possible but not guaranteed.

ADDITIONAL SETTINGS

1. The device is equIPped with a function of voice notified in modes / states of operation.
To turn off the voice announcements, briefly press the control / reset button once.
After releasing the button, a confirmation beep will sound.
A second short press on the control / reset button again activates the voice prompts.

2. In the advanced camera settings menu, users can configure / change the following parameters:
Change device name
View a list of trusted persons who have access to the device
View basic device information
Enable / Disable Date / Time Stamp
Configure motion detection settings
Configure the settings for recording to a memory card
Check for firmware updates
Unlink / unlink the device to the current account (required to link the camera to another account).

3. Through the account settings menu (section Personal Account), users gain access to the following functions:
Setting up an account profile
Access to the message center. View events for which notifications were received

4. In the ScrIPts section, users have the ability to configure the automatic execution of various scrIPts when trigger events occur, or to run scrIPts manually.

5. Using a wired connection.
A wired connection to the local network is used as the main or backup channel for communication with the Internet. Its use becomes possible only after the initial configuration of the device is completely completed and it is linked to the account.

The list of available functions may change as the system is improved.

1. Lens
2. Infrared illumination
3. Light sensor
A. Control / Reset Button
5. Built-in speaker (under the cover)
6. Power connector
7. Built-in microphone
8. Slot for memory card (under the cover)
9. RJ45 connector
10. Swivel mount
11. External detachable antenna
12. Protective cover for SD card compartment
13. Removable hood

READ  Connecting IP Camera To Nvr

Device management
The device is controlled:
1. Remotely via mobile app
2. In manual mode using the control / reset button

Use short press on the button to turn on / off voice prompts.

Long press ( than 5 s) resets the parameters to factory settings and puts the device in the configuration / pairing mode.

Attention!
When the device is put into the configuration mode, the device parameters are reset to their default values, including the reset of the wireless network access parameters. To regain remote control over the device, it will need to be reconfigured using the application.

Attention!
When you reset the settings, the device is still linked to the account. To link the camera to another account, you must first deregister from the current account.

Precautionary measures

The device is assigned an IP63 protection class, which means that the device is reliably protected from dust and vertically falling splashes from above, including atmospheric precIPitation.
Do not immerse the device in water or expose to liquid jets.
Always observe the orientation when mounting the device: the camera must be installed so that the protective cover of the SD card compartment is facing straight down.
When installing the protective cover of the card compartment Make sure that the cover, gasket and cover seat are dry and clean, free of dust, moisture and foreign particles. After installing the cover, always tighten the fixing screws securely.

Technical support

DO NOT disassemble or repair the device yourself. In the event of a malfunction Contact the service center.
Permissible ambient temperature during operation: from 0 to 35 C. Storage temperature: from 5 to 45 C.
Avoid contact of the device with fire sources to avoid explosion or fire.
DO NOT expose the device to extremely high or too low temperatures.
Do not spill water on the device.
Do not drop the device or hit it with other objects. DO NOT subject the device to strong mechanical shock.
Avoid contact of the device with sources of electromagnetic radiation.
DO NOT use chemicals or detergents to clean the product; always turn off the device before cleaning.
Use only manufacturer approved accessories.

Main settings
Input: DC 12V. 1A
Power consumption: 9 W 12 W

Installation rules and conditions
This device does not require any mounting or permanent fixation.

Storage conditions
The device must be stored at temperatures from 5 to 45 С with a relative humidity of NOT more than 85%, and also avoid direct sunlight.

Transportation conditions
It is recommended to transport the device in its original packaging.

Terms of sale
To dispose of the product, contact an Authorized Service Center.

date of manufacture indicated on the package.

Life time the product is 24 months from the date of sale, but not more than 30 months from the date of production.

Wi-Fi IP Sannce I21AG PTZ camera. Instructions for setting up in Russian

Instructions for setting up the camera are presented on the example of the Sannce I21AG camera model

This guide describes how to configure and connect the Sannce camera using a mobile application, as well as configure archive recording and playback.

1. Unpack the camera

3) Mounting base

5) A bag with self-tapping screws and tools for resetting settings

2. Download and install the free Sannce cam application on your smartphone (from PlayMarket or App Store)

3. Connect the power cable to the camera and connect the power adapter to the mains to turn on the camera.

After connecting the power, the camera will start downloading. Wait until the camera is fully loaded.

To set up, the phone must be connected to the Internet via your Wi-Fi network

4. Run the application and click Add Device

5. Click the button at the bottom of the Wireless Configuration Wi-Fi screen.

6. Click Camera

7. Click Next

8. A window will open in front of you, in which the data for connecting to your Wi-Fi network must be indicated. After specifying the network name and network password, click the Start Configuration button

9. Bring the phone closer to your camera and wait for the camera to say that the setting was successful. While configuring the camera, the following window will appear on the screen

10. After you finish configuring the camera, it will be displayed on the phone screen. If this does not happen, repeat the setup again.

Click the found camera on the phone screen

11. In the new window that opens, click the button to Confirm (Done) to save the camera settings

12. Next, the program requests to change the camera password. Click OK

13. Enter the new administrator password and click Done

14. Click on the added camera to open live view

15. An online view from the camera will open before you. To rotate the camera SwIPe up, down, left or right on the phone screen.

To open additional functions, click on the corner of the screen where the red arrow shows.

16. After clicking on the screen, additional buttons will be displayed

17. To change the image quality, click on the highlighted button and select the required quality

18.To use two-way audio transmission, click the speaker button

19. To adjust the brightness, click the highlighted button in the next picture.

Sannce Wi-Fi camera archive recording and playback

To record the archive, insert a memory card into the upper slot of the Sannce camera

Next, in the Sannce Cam mobile application, open the device letter and click the settings button near the camera

In the settings, open the “SD setting”

Click “SD card format” and then click OK to confirm formatting the card

Comment: After formatting the card, enable the desired recording modes: record coverage, voice record, timer recording. To do this, click on the corresponding switch to switch it to “on” mode.

To view the archive in the Sannce Cam application, you must go back to the device list and name it “Messages”

Now you need to name the camera itself

READ  Reset IP Camera Settings to Factory Defaults

Now, at the bottom of the screen, press the button to display the archive (local records or remote records)

Optimus IP Camera Connection

First you need to connect the camera to a power source. The connector supports 5V DC. Please note that the camera can be seriously damaged if the power source is selected incorrectly.

The surveillance camera is connected to the Internet Explorer browser according to the following aLGorithm:

  • Load the camera and then attach it to a router or switch.
  • Compare the IP address of the router and the camera. They must match.
  • To download the upgrade tools that need to be installed via the Upgrade Tool, you need to use the CD-ROM.
  • After launching the Upgrade Tool, you need to go to the search for IP addresses, clicked the IP Search button. Found devices can be seen here.
  • In the list you need to select the required device and apply the settings to it using the Modify button.

To connect a device to a Wi-Fi network, you need to go to the device manager, and then click the Advanced button there. Then select the Wi-Fi setup item. In this menu, you will need to search for networks and find your own, and then apply the new settings (assign an IP address automatically) and reboot the device.

We look at the connection of IP cameras optimus

Optimus IP Camera Configuration

IP surveillance cameras, which are produced under the Optimus brand, are distinguished by a large number of positive characteristics. They are very reliable and also compatible with various devices. Recordable, high resolution. On top of everything GoPro, Optimus IP cameras support almost all browsers, mobile operating systems and dual streams.

However, in order to obtain an excellent image quality, it is necessary to professionally set up a surveillance camera. Correct and competent setup can ensure the correct functioning of the entire tracking system.

Optimus IP Camera Device

The Optimus IP camera is a tracking device with all the elements in a single housing. Camera interfaces are distinguished by the presence of a large number of different inputs and connectors. On the back of the device there is a power connector, an output for connecting a wire for transmitting audio information.

Also on the back of the Optimus camera there are the following outputs: an RJ-45 connector, an attachment for a bracket to mount the camera to the desired location, and alarm inputs / outputs. On the side panel you can see the output in which a micro-SD memory card is installed.

Configuring IP camera Optimus

If a situation arises when the IP address of the tracker is unknown, then you can use the CD-ROM and start the Net_Admin program. It will help you find out the connection settings, and then change them if necessary. In this case, you need to perform the following sequence of actions:

  • Run utility.
  • Press the Refresh button, after that you can see all cameras in the list.
  • Select the required camera by clicking on its name once with the left mouse button.
  • Enter new network settings and click the Change IP button.

Optimus surveillance cameras have a wide range of different settings, but first of all, you will need to go to the settings for recording information. To do this, you need to enter the main menu with settings, select the Record option and find the Record Settings item there. In order for the device to be able not only to Record information, but also to write it to a specific medium, it is necessary to install at least one hard disk that allows reading and saving data.

Reproduction of information is possible in two ways:

  • Through the Main Menu. In this case, you need to use the Record category and click the Play item;
  • Through the menu that is present on the Desktop.

Network connection settings are made in the Network menu. Here you can select a network card, as well as set the parameters for IP addresses, gateways and subnet masks. Once the DNS address is set, the camera needs to be rebooted.

To go to the camera connection settings, you must select the Digital Channel Setting category. Here you can select the configuration of the device via the Channel mode item. The applied configuration will work after rebooting the IP camera. In addition, in the same menu, you can configure the mode and state of the channel.

Optimus cameras differ in different modifications: IP-P and IP-E. The former work over the ONVIF protocol, and the latter over the NETIP protocol. Accordingly, the settings of THESE cameras are also different. Optimus IP-P cameras have port 8080 and the password will be 1111, while IP-E devices have port 34567 and passwords require.

Optimus IP addresses by default

By default, the IP addresses for connecting the surveillance camera and router to the local network have the following sequence of numbers: 192.168.1.10.

The factory settings, which are used by default in the cameras of the Optimus brand, have the following data:

  • Subnet Mask: 255.255.255.0
  • User name, or User name: admin
  • Password, or Password: absent by default (or you can try to enter 1111)
  • Gateway, or Gateway: 192.168.1.1
  • HTTP port 80
  • Media port: 34567
  • Faster Download: The default is high speed download
  • Enable DHCP. This item allows you to obtain an IP address automatically. Professionals do NOT recommend ticking this box.

It is necessary to take into account the fact that the login and password have sensitivity to the selected case. In addition, remember or write down the password to access the surveillance system. If you enter it incorrectly for three times in a row, the alarm option will be triggered. If you continue to enter the wrong entry two more times, the account will be locked. To unlock, you will need to reboot the account or wait for half an hour, and then the record will be unlocked automatically.