Honor 10 Lite Screen Problems: How To Fix It

The Honor 10 Lite is a mid-range terminal that was released in November 2018. The terminal still maintains specifications at a 6.21-inch FullHD screen with 1,080 x 2,340 pixels, dual rear cameras and a 24-megapixel selfie sensor. In addition, it has a Kirin 710 chip and options for up to 6GB of RAM. However, as usual, this terminal is not without problems.

It is almost impossible to find a mobile phone that does not suffer from any other problem. Fortunately, specialized forums and portals like MovilZona are trying to find solutions to these problems. In the case of Honor 10 Lite, some problems have been reported with its screen, which can be solved in most cases.

Factory settings

The moment that no one wants, but which is usually the final decision. this is to restore the device to factory settings. This method is more cumbersome as it will erase all system data. To do this we go back to recovery mode and this time we select the “clear cache / factory reset” option and press the power button to confirm. When the phone turns back on, we need to make sure the problem is gone before reinstalling any app.

Why is the screen flickering

Some users have reported flickering on the screen of their Honor 10 Lite which can be of higher or lower intensity and which can be more or less continuous depending on the case. In most cases, this is due to a software problem, so we will have to try several possible solutions to fix the problem.

Partial reset

As we say, software is usually responsible for this screen problem in Honor 10. For this we can do a partial reset that will allow you to load the system cache and avoid conflicts with files that may have been corrupted. In this case, we will have to press the power button for 45 seconds. We wait for the device to reboot and after turning it on, we have to check if the problem is gone.

Enter Safe Mode

It is very likely that some downloaded application is causing the problem. To find the guilty software, we have to restart the mobile in Safe Mode. This will prevent this application from being loaded into the system and generate an error. To do this, leave the power button pressed for a few seconds and release when we see the Honor logo. Then we press and hold the volume down key and hold it until the terminal reboots completely.

After restarting, we should see “Safe Mode” at the bottom of the screen. If the problem does not appear when we are in this mode, it means that some application is causing an error. To do this, we will have to uninstall the installed apps in order from new to old and check if the flickering disappears.

Updating the software

The first step is to check which terminal has the latest software version for the system. This is the first step that we must always take before looking for other solutions. Many Honor 10 Lite users have fixed the screen problem For example, Honor has introduced several patches that fix compatibility issues and malfunctions throughout the history of the device.

To do this, we need to check the notification bar to make sure we have no pending updates. We also need to go to the Settings / Updates system and check your.

Honor 10. sound setting

The developers have built a good speaker into the Honor 10 with an extensive choice of volume levels, and the sound does not turn into an incomprehensible noise or scream at maximum levels. over, the manufacturers have left in the device a standard 3.5 mm jack for a headset or headphones, which the older smartphone Huawei P20 cannot boast of.

Equipped with the AK4376A audio chip, the Honor 10 offers rich audio capabilities that are high quality and loud for a comfortable listening experience.

Setting up Huawei Histen

With Huawei Histen technology, you can customize the sound yourself, where different algorithms maximize the audio capabilities of the Honor 10.

To enter Huawei Histen, the user needs to connect headphones to the standard jack, then open “Settings”. “Sound”, select “Huawei Histen Audio Effects”.

honor, lite

Here you can select the type of headphones, so the system will automatically adjust to the optimal sound. The following choices are offered:

  • by the type of headphones;
  • by model.

If in-ear headphones are turned on, then the sound will add volume. When using in-ear headphones. high-quality bass, and by choosing on-ear headphones, Accent will appear on the high frequencies, while vocals will be in front.

In Huawei Histen, you can independently choose the appropriate sound depending on your personal needs, capabilities and desires.

If the user enables 3D audio, the settings will look like this:

Here you can see the different effects: close sound, front, surround and maximum sound. Everyone has the right to make their own choice, experimenting with the settings and choosing something to their liking and taste.

Equalizer Honor Purity

The Huawei Histen menu offers a selection of the desired sound effect. For example, 3D audio, natural or normal audio. When choosing a normal sound, the technology will offer to use an equalizer of 10 bands, where you can manually adjust the sound as you wish, and then save or reset the settings, starting over.

Here you can correct the sound based on the type of headphones, hiding their flaws and bringing their advantages to the fore.

For those users who do not want to waste their time adjusting the equalizer, there are other settings in the equalizer, where the following choices are:

  • pop;
  • classic;
  • rock;
  • jazz;
  • dance.

Depending on the genre of music, any owner can easily customize the sound to suit individual needs.

The Honor 10 has a good and loud sound. This is the main merit of the built-in DAC. Using high-quality headphones, listening to music is a real pleasure, and thanks to Huawei Histen algorithms, you can customize the effects for yourself. There is another pleasant moment. In Honor 10, manufacturers have added noise cancellation, which works effectively, really reducing the volume of noise in the background.

In addition, the smartphone has a 10-band equalizer, where users can also adjust the sound quality depending on the type of headphones or the genre of music they listen to. The sound does not turn into indistinguishable noise, even if the volume is turned to maximum. By the way, adjusting the volume level is very simple: for this, the developers have created 2 buttons on the right side of the device (volume up and down):

Manual for Huawei Honor 10

This is the official instruction for Huawei Honor 10 in Russian, which is suitable for Android 8.1 Oreo, EMUI 8.1. In case you have updated your Huawei smartphone to a more “fresh” version or “rolled back” to an earlier version, then you should try other detailed operating instructions, which will be presented below. We also suggest that you familiarize yourself with the quick user guide in question. answer format.

If the operation manual did not help you find the answer, then please ask a question on the same page. We will definitely help.

You have come to the point, because all the information from the official website of Huawei is collected here, as well as a lot of other useful content.

Settings— About phone :: Android version (a few clicks on the item will launch the “Easter Egg”) [“Out of the box” version of Android OS. 8.1].

You need to go to “Settings. About phone. Kernel version”

How to enable Russian keyboard layout

Go to the “Settings. Language & input. Select language” section

How to connect 4g or switch to 2G, 3G

“Settings. Mobile network. Data connection”

What to do if you turned on kid mode and forgot your password

We go to the “Settings. Language and keyboard. section (keyboard and input methods). put a tick in front of” Google voice input “

Honor 10 lite disassembly LCD replacement

Settings— Display :: Auto-rotate screen (uncheck)

Settings — Display — Brightness — right (increase); left (decrease); AUTO (automatic adjustment).

Settings. Battery. Power saving (check the box)

Enable display of battery charge status as a percentage

How to transfer phone numbers from SIM-card to phone memory? Importing numbers from a SIM card

  • Go to the “Contacts” application
  • Click on the “Options” button. select “Import / Export”
  • Choose where you want to import contacts. “Import from SIM-card”
READ  Transfer data from Xiaomi to honor

How to add a contact to the blacklist or block a phone number?

How to set up the Internet if the Internet does not work (for example, MTS, Beeline, Tele2, Life)

  • You can contact the operator
  • Or read the instructions for setting up the Internet

How to set a ringtone to a subscriber so that each number has its own melody

Go to the “Contacts” application. Select the desired contact. click on it. open the menu (3 vertical dots). Set a ringtone

How to disable or enable vibration feedback from keys?

Go to Settings. Language and input. Android keyboard or Google keyboard. Vibration feedback (uncheck or tick)

How to set a ringtone for an SMS message or change notification sounds?

How to find out which processor is on Honor 10?

You need to look at the characteristics of the Honor 10 (above is the link). We know that this modification of the device has a chipset. HiSilicon Kirin 970, 2.36 GHz, 4 x Cortex-A73, 4 x Cortex-A53, Mali-G72 MP12.

Settings. For Developers. USB Debugging

Settings— Data transfer— Mobile traffic. Settings— — Mobile network— 3G / 4G services (if the operator does not support, select only 2G)

How to change or add the keyboard input language?

Settings— Language and input— Android keyboard— settings icon— Input languages ​​(puts a check mark next to the desired ones)

Change of location and firmware of HwOTA smartphone

This method will help you upgrade to firmware that is not yet available for installation, or roll back to the previous firmware if the update turns out to be more buggy than the previous build (Android 8 over Android 8 with both an increase in the firmware build and a downgrade of the build).

To change the location on the smartphone and flash it using the HwOTA method, you must:

  • Unlocked bootloader or the presence of a code to unlock it (which will help unlock it);
  • Enable the factory unlock feature in the developer menu (for all regions except China). She is not in the Chinese phones until they changed the location;
  • Enable the USB DEBUGGING function in the developers menu (a controversial point, like the body in tvrp);
  • SD card with at least 4 GB;
  • Stock recovery.

On your phone, back up “everything from everything” if you can (since all data will be erased during the update process). These are the conditions. so get ready;

In the “developer’s” settings, check “factory unlock” (there is no such item in China, but it will appear as soon as you change the location) and enable “USB debugging”;

Add downloaded files to the “HWOTA \ Update” folder, the script will automatically rename them according to the template: update_data_full_public.zip to update_data_public.zip

This method is hardcoded. therefore, all the variety of files eu, cn, meanhaf, specseas must be brought to a single form. The installation script at the very beginning will remind you of what and where to put, it will rename (you do not need to rename) and patch the firmware files! Checking for update packages is disabled in Recovery, so we can install any firmware (Android 8) of our device, and I also rewrote the script: added automatic renaming of firmware files to the desired template, added auto-patching, fixed copy blocks and much more;

Run the universal bat file update.bat in the “HWOTA” folder, which will provide an opportunity to choose the option we need to work (change the firmware / rebrand (change the location)); In the beginning, it will ask you “patch files or not” (if you have patched, then you do not need to re-patch)

Then follow the detailed instructions on the screen. At the end of the process, everything should work

The location is changed by selecting a specific item and selecting the oem-info file from the list (14 types of locations are available, all DS). After changing the location, you need to boot into the recovery stock and make wipes. If you are making an international version from pure Chinese, then be prepared that after changing the location you will have an fpr lock item in the fastboot. Therefore, after changing the location, you need to boot into the recovery stock and make wipes from it. Accordingly, it must be in its place before starting all the manipulations to change the location and firmware. Another reason why you need to install tvrp in the recovery section, tk. after changing the location, the phone must automatically reset. After the reset, it will boot into the system and the factory unlock item will already be available there. Turn on the factory unlock and unlock the bootloader on the new one. After that, run the batch file on a new one and sew the required firmware.

Honor 10 firmware via standard recovery

For the Honor 10 smartphone, the original firmware can be downloaded from the link H10_B104_STOCK_RAMDISK (COL-L29C432B104), or any other through the special firmware search program Hw Firmware Finder, and then copy it to the “dload” folder on the device’s internal memory. If such a folder is not found, it will need to be created.

Free space on the internal drive must be at least 8GB, if you don’t have that amount of free memory, use an SD memory card. The card must be in good working order and correspond to a reading class of at least 10.

The battery must be at least 50% charged, and best of all fully charged.

After copying the firmware to the smartphone, be sure to disconnect the USB cable from the PC, otherwise the smartphone will enter Manufacture Mode and the installation will cut off by 5% or freeze by 90%. We go on the phone to the forced firmware mode. To do this, turn off the smartphone and hold down three buttons. volume “”, “-” and the power button.

After that, the smartphone will boot from standard recovery and automatically start the process of installing the new firmware.

Huawei honor 10 firmware manual

Instructions on how to flash a huawei honor 10 smartphone to the official or custom firmware, change location and HwOTA firmware, unlock the bootloader on the phone and install custom TWRP recovery, install custom firmware.

Absolutely all phones from Huawei (Honor is a subsidiary of Huawei) can be flashed through the built-in recovery or through TWRP, it is an installer.

It is also possible to partially flash the firmware via Fastboot (System, Boot, Cust, Recovery), which makes it possible, for example, to restore the phone’s performance after user intervention with ROOT rights or a system failure. There are programs for installing firmware, such as Sony’s Flashtool, but it is paid by DC Phoenix.

Unlock Huawei honor 10 bootloader

Get an unlock code on the Huawei website or for a fee on other resources.

We go to the official website using the link. In the upper right corner, click on the inscription Unlock

On the next page, you need to go through the registration procedure. Fill in all the fields and click Register.

Further more interesting, Many simply press further and follow the instructions, but here you must first select Register Email Address. since By default, registration by telephone is selected (Asian numbers only). We select and see the human account registration window, Enter all the data, as in the picture below.

After successful registration, you are automatically authorized on the site and transferred to the agreement page.

Further, according to the scenario, the page where you need to enter your phone data:. In the first field, select the EMUI version, which is now relevant for your honor 10. In the second field, do not touch anything. In the third field Product Model. In the phone, go to Settings. Scroll to the most bottom. About the phone. The very first item Model. COL-L29. I suppose that something completely different is written on the Chinese firmware, you can, of course, enter what is written there, but if it does not work, then we write in the version like here In the fourth field. Serial Number. in the About phone settings menu. Left S / N: R8Q …… This is rewritten In the fifth field: Again under the cover, well, or in the settings menu About phone. IMEI. But, the case is already open anyway, so from here we take IMEI1: 866 If it does not fit we take IMEI2 Sixth field: Product ID. We open the native dialer in the phone. We type the command ###. We get the code. and drive it in

Seventh field: Code from the picture. Checking. And click COMMIT. If everything is correct, your cherished honor 10 bootloader unlock code will appear on the next page.

Enable “factory unlock” (FRP unlocked) in the developer settings or disable the SEARCH PHONE function from Huawei on the Chinese firmware.

Put your smartphone into Fastboot / Rescue mode and connect to your PC. To do this, turn off the phone, hold down the volume down button and connect the USB cable.

On a PC, in the Command Prompt window, enter the command

Installing custom TWRP recovery on Honor 10

To install the modified TWRP recovery, the bootloader must be unlocked on the smartphone and the factory reset protection must be removed.

Follow the instructions above to install the minimum version of ADB on your PC. Then you need to download custom recovery twrp_bkl_0.7 for Honor 10 for Honor 10

Put your smartphone into Fastboot / Rescue mode and connect to your PC. To do this, turn off the phone, hold down the volume down button and connect the USB cable.

On a PC, in the Command Prompt window, enter the command

fastboot flash recovery_ramdisk twrp_bkl_0.7.img

The process of flashing the recovery will start. Upon completion, you can disconnect the USB cable and restart the smartphone.

READ  How to unlock honor if you forgot your graphic password

Installing custom firmware on Honor 10

Installing custom firmware on honor 10 via TWRP recovery To install the firmware in this way, TWRP recovery must be installed on your honor 10, if this is not done, you can install the recovery according to the instructions above.

lineage-15.1-UNOFFICIAL-berkeley-8.1 or whatever you like.

and copy it to the internal memory of the smartphone in the root folder.

We reboot the smartphone into TWRP recovery (Turn off the device. Press the volume up and power keys until vibration, release and wait for the entrance.), And there we go to the Advance Wipe menu, change the Data file system to EXT4. We go back and do Wipe, partitions. cache, data, dalvik and system

After wiping the device, go to the “install” menu, in the submenu, select the ZIP file of custom firmware for honor 8 lite, swipe to the right to start the firmware process.

The process of installing the firmware usually takes a couple of minutes (the time depends on the size of the firmware), at the end of the firmware, restart the phone.

How to record screen video with sound on Huawei smartphones and tablets.

1) The first method allows you to easily and quickly record a video of all activities on the Huawei screen. To start recording from the display, you must simultaneously press and slightly hold the “Volume Up” button and the “Power” button.

2) You can record from the screen by pulling the screen down from the top to open the notification panel, in the list that opens, select and click on this icon.

3) The third method allows you to start recording a video screenshot of the Android Huawei screen with your knuckles. You need to double-touch the screen with the knuckles of two fingers as shown in the attached screenshot below, after which the content and all actions with sound will start recording.

You can stop recording by clicking on the “recording icon” located in the upper left corner of the display or by simultaneously pressing the “volume up button” and the “power” button or by double-tapping the screen with your knuckles as shown in the picture above. Who does not have the function of recording from the screen, try turning it on by opening “Settings” then “Control and Accessibility” next “Movement” then in the item “Smart screenshot” turn on and then try to record the video from the phone screen again.

You can view the saved video screenshots in the “Gallery” in the “screenshots” or “screen recording” album. If necessary, you can transfer via Bluetooth or the Internet, as well as delete records.

How to set up sleep mode on Honor 9 and similar Android smartphones and tablets.

Sleep mode on Honor. On this page, you will find instructions on how to set up the sleep mode of Huawei Honor 9 and similar Android smartphones and tablets. This function allows you to save battery power by automatically turning off the phone screen after a specified time when you are not using the device.

To adjust the sleep mode of the Honor screen, that is, set the time for automatically turning off the screen when inactive. Open “Settings” on your smartphone. In the settings, select the item “Screen”. Look at the attached pictures below. In the screen menu that opens, select the “Sleep mode” item. Now we set the sleep time of the screen when idle, choose from “15 seconds to 10 minutes” or “never” so that the screen does not turn off at all. In other smartphones and tablets, the time to automatically turn off the screen when not using the phone may be different.

What to do if you cannot change the sleep mode time in the screen settings, although there is such an item and there, for example, 30 seconds are set without the ability to change.

Yes, this also happens when the hibernation mode on Huawei Honor is not active and there is a time of 30 seconds of inactivity after which the screen turns off. Sometimes the screen can automatically turn off after 30 seconds even when watching a video, which can cause inconvenience to the user. And so if you cannot change the sleep mode time, then most likely the “Power Saving Mode” is enabled on the Huawei Honor phone or tablet. To turn off the power saving mode, open “Settings”, then “Battery” and in the menu that opens, select the item “Power saving mode” opposite which we disable this function. Now you can change the sleep time as shown above.

Navigation

Navigation styles are presented as desktop layouts. In addition, you can enable the fourth button on the navigation bar. It is designed to view notifications. One of the interesting navigation features is smartphone control using gestures.

Set Up HUAWEI Honor 10 lite. Activate & Configure

To use this style, you need to follow these steps:

  • Settings
  • System
  • System navigation
  • Style selection

Photo camera

The main resolution of the main camera is 81013 MP. The focal length of the first lens is 26 mm, aperture is f / 18. Thanks to the AI ​​function that coordinates the photo sensors, the user has access to automatic shooting modes.

  • “Night”. shooting mode in low light conditions.
  • “Portrait”. allows you to take high-quality pictures
  • “Aperture”. increases the aperture and depth of field of the picture.
  • “Video”. recording high quality video clips

Intelligent modules give limitless possibilities for photography in Pro mode. An experienced user can manually adjust the camera, take a professional photo by changing the sensitivity, aperture and shutter speed.

Pro mode offers the use of panorama effect, time-lapse, mask, overlay music and background. In the camera interface, you can turn on the auxiliary grid and quickly launch the application. You can open additional menus by swiping to the right.

The selfie camera uses a 24MP sensor with a 26mm focal length like the head camera. Despite its smaller aperture, f / 2.0 is a powerful tool for portraits. If you want to blur the background, you need to enable the corresponding function.

Display color adjustment

Screen color tones affect vision and battery power. The EMUI graphic shell automatically adjusts the screen temperature, choosing the optimal mode. Users can, but not recommended, manual color calibration.

To try warmer tones that are easier to view, follow these steps:

  • Settings
  • Display
  • Color Mode and Temperature

Fingerprints

The fingerprint sensor is used not only to unlock the screen. It can be programmed to control various telephone functions. Such as:

  • Pick up the phone
  • Turn off the alarm
  • Viewing Photos
  • To take a photo
  • View notifications

The function of the sensor is changed in the following sections:

  • Settings
  • Security and privacy
  • Fingerprint

Monitor apps to save battery

The EMUI GUI collects application statistics, including energy consumption. Disabling background applications can help prevent battery draining quickly. To do this, go to the following sections:

  • Settings
  • Battery
  • Additional settings
  • Battery consumption details

Screen resolution

This function is used to enhance the image quality. Decrease the resolution to save battery power. Honor 10 Lite can be set to Full HD or enable the Smart function, it automatically selects the optimal resolution and color rendition.

To change the screen resolution you need to go:

  • Settings
  • Display
  • Screen resolution
  • Make changes

Honor 10 Lite setup, tips and tricks

Honor 10 Lite is a phone with a wide range of technical capabilities and an optimal price. Huawei uses the latest generation EMUI 9 GUI based on the Android Pie operating system. A distinctive feature of the software is variable settings for the needs of the user. The article discusses some useful options for customizing Honor 10 lite available in this smartphone.

Hide keyhole

The smartphone has a teardrop notch for a selfie camera. If it is inconvenient, the user can hide it. The option is available in the sections:

  • Settings
  • Display
  • Additional settings
  • Groove

As a result of such actions of dimming the status bar, the working area of ​​the screen will visually decrease.

Sound settings

When watching movies or playing games, the device automatically switches to stereo sound mode. You can customize different ringtones and notification tones for different scenarios. Adjusting the system volume: Press the volume button, then press. to adjust the ringtone, media, alarm, and conversation volume. The volume can also be adjusted in the system settings. Open the Settings app, tap Sound and drag the slider to adjust the volume. Switch between Sound, Vibration, and Silent modes: Swipe down on the status bar to open the notification panel icons tab. Tap to switch between Sound, Silent and Vibration modes.

Turn on keyboard sound and notification tones: Open the Settings app, select Sound sound settings to turn the keyboard and notification tones on or off. To turn on Silent mode: On the Sound screen, turn on Silent mode. After turning on Silent mode, turn on Vibrate in Silent mode. When there is an incoming call, the screen will light up and the device will vibrate. Customize ringtone and notification tones: From the Sounds screen, select a ringtone or use Notification.

Clean up memory to improve performance

Does your device start to work slowly over time? Want to clean up your system memory but don’t know exactly which files to delete? Clean up memory can quickly clear cache memory, remove large files, residual files, and unused application files, and improve the speed and performance of your device. When device performance decreases or memory is low, Phone Manager offers to clear memory. Clean up memory or free up space on your device’s memory by following the onscreen instructions. Cleaning: Quickly find and delete unnecessary files, clear cache memory, free up space in the system and internal memory of the device without affecting its operation. Thorough cleaning: Search for unnecessary files including WeChat files, large files, videos, pictures, residual app files, music files, unnecessary installation packages, unused files and files that take up a lot of memory space, and get recommendations for cleaning up memory based on the results system scan. This allows you to safely clean up memory without the risk of accidentally deleting important files. Turning on the memory cleaning function As the device memory becomes full, performance may decrease. Use Memory Cleaner to free up memory space, improve system performance, and keep your device running smoothly. Open the Phone Manager app, click Memory Cleaner, and clear the system and cache memory based on the scan results of your device. If this operation does not increase the memory space, perform a thorough memory cleaning based on the results of the system scan and the suggested recommendations.

READ  How to take a long screenshot on honor

Honor 10 customization, secrets and tricks

A bright phone with a gradient glass cover not only looks good, but also inside. The memorable “wrapper”, shimmering in the light shades of blue from turquoise to purple, hides no less tasty content: a powerful flagship chip Kirin 970, 4 GB of RAM “in the base” and a storage capacity of 64 GB. But you need to be able to manage this power, in this article we will analyze in detail the main useful settings.

Setting the home screen wallpaper

Tired of the default wallpaper? You can set your favorite photo as your home screen wallpaper. Open the Settings app, select Screen Wallpaper. Available options: Setting the picture as the home screen wallpaper: Touch Set wallpaper. In or Gallery, follow the onscreen instructions to select an image, select Lock screen, Home screen, or Home screen and lock screen. Customize wallpaper: Turn on Customize home screen wallpaper and adjust the Interval and Album settings. Setting a picture as your home screen wallpaper: Want to set a photo as your home screen wallpaper? In Gallery, open a photo, select Set as Wallpaper. Follow the instructions to set the photo as your home screen wallpaper.

Managing home screen widgets How do I quickly manage home screen widgets? You can add, move or remove widgets on the home screen. Adding widgets: Touch and hold an empty area of ​​the home screen to enter edit mode. Tap Widgets, select a widget, drag it to an empty area of ​​the home screen.

Removing widgets: Touch and hold a widget on the home screen until the device vibrates. Drag the widget to the Delete icon at the top of the screen. Move widgets: Touch and hold a widget on the home screen until the device vibrates. Drag the widget to the desired location.

Using the Application Screen Feel like there are too many application icons on the home screen? Turn on the Apps screen to free up space on the home screen. Open the Settings app, go to Display Home screen style, and turn on Apps screen. To switch to the normal home screen style, select Normal.

Clean up memory to improve performance

Does your device start to work slowly over time? Want to clean up your system memory but don’t know exactly which files to delete? Clean up memory can quickly clear cache memory, remove large files, residual files, and unused application files, and improve the speed and performance of your device. When device performance decreases or memory is low, Phone Manager offers to clear memory. Clean up memory or free up space on your device’s memory by following the onscreen instructions. Cleaning: Quickly find and delete unnecessary files, clear cache memory, free up space in the system and internal memory of the device without affecting its operation. Thorough cleaning: Search for unnecessary files including WeChat files, large files, videos, pictures, residual app files, music files, unnecessary installation packages, unused files and files that take up a lot of memory space, and get recommendations for cleaning up memory based on the results system scan. This allows you to safely clean up memory without the risk of accidentally deleting important files. Turning on the memory cleaning function As the device memory becomes full, performance may decrease. Use Memory Cleaner to free up memory space, improve system performance, and keep your device running smoothly. Open the Phone Manager app, click Memory Cleaner, and clear the system and cache memory based on the scan results of your device. If this operation does not increase the memory space, perform a thorough memory cleaning based on the results of the system scan and the suggested recommendations.

Fingerprint sensor

Fingerprint Scan: Quick Navigation and Better Security The fingerprint scan feature not only quickly unlocks your device, but also provides additional protection for your data. Fingerprint scanning supports the following features: One-touch screen unlock: Tired of entering your PIN or drawing a pattern to unlock the screen of your device every time? Scan your fingerprint to unlock your device quickly and safely. Access to personal files: Are you afraid to forget the password for the Personal section or the App Lock function? Afraid that other people will find out your password? Set up your fingerprint to access the Personal sections

Registering a fingerprint Register a fingerprint on your device to unlock the screen or open the Private or Locked Apps section without entering a password. Fingerprint unlocking is available only when Pattern, PIN, or Password is selected as the unlock method. After restarting the device or when fingerprint recognition fails, you will have to enter the password to unlock the device. To register your fingerprint, your finger must be dry and clean. 1 Open the Settings app. 2 Select Security & privacy Fingerprint, then select Pattern, PIN, or Password and follow the onscreen instructions to set up an unlock password. 3 After setting up the unlock password, click New fingerprint to enroll your fingerprint. 4 Place your finger on the fingerprint sensor. Press down on the sensor until the device vibrates. Repeat this step, scanning different parts of your fingertip. 5 When the fingerprint registration is complete, click OK. To unlock the screen, place your finger on the fingerprint sensor.

Adding or changing a fingerprint Honor 10 can add a maximum of 5 fingerprints. You can rename prints and delete them. 1 Open the Settings app. 2 Select Security & privacy Fingerprint. 3 Enter the unlock password. Then follow the instructions to go to the fingerprint setup screen. 4 The following actions are available in the Fingerprint List section: Fingerprint enrollment: Click New fingerprint to add a new fingerprint. Change name or delete a fingerprint: Tap on a saved fingerprint to change its name or delete it. Fingerprint identification: Tap Fingerprint recognition to identify and mark enrolled fingerprints.

Navigation bar customization

Using the navigation bar, you can return to the home screen or the previous screen, close an application, or view a list of recently used applications. On devices with a front navigation button, the virtual navigation bar is disabled by default. After enabling the virtual navigation bar, the front navigation button will be disabled. The device will not respond when you press and hold or swipe over it. To customize the navigation bar, open Settings, select System System Navigation, then Virtual Navigation Bar. Click Settings to choose a combination of buttons.

How To Setup The HONOR 10 Lite

Show and hide the navigation bar: On the Virtual Navigation Bar screen, tap Settings to enable the Navigation Bar. Then click on the navigation bar to hide it. When the nav bar is hidden, swipe up from the bottom of the screen to show it.

Back button: Tap to return to the previous screen or close an application. Tap to hide the onscreen keyboard after entering text. Home button: Press to return to the home screen. Press and hold to display the HiVoice icon, swipe up to enable HiVoice features. Browse button: Click to open a list of recently used applications. Press and hold to enter split mode. Notification panel open button: Press to open the notification panel.

Configuring Camera Settings

On the Settings screen of the Camera application, you can configure various settings, modes, and camera features. Shooting by tapping on the camera screen. Open the Camera app, tap to open the Camera app Settings and enable Tap capture. When you touch an object on the screen, the camera will automatically focus on it and take a photo. Automatic shooting when a smile is detected. On the Settings screen, turn on Smile. The camera will automatically take a photo when it detects a smile. Fixing the focal length. On the Settings screen, tap Press and hold shutter button and select Focus lock. When you press and hold the capture button, the camera will not change the focus value. Use the volume button to take a photo, focus, or zoom in and out. On the Settings screen, press the Volume button and select Shutter, Zoom or Focus. Save images in RAW format. detailed images are saved in RAW format, which allows them to be further processed. In professional mode, press. to open the Settings screen and enable RAW Format. When you take a photo, the image will be saved in RAW and regular format in a dedicated folder in Gallery. Turn off the shutter sound. On the Settings screen, enable the No.

BYRGPUB.COM 2021