Yoosee camera. Wireless PTZ IP Camera Configuration Manual

The PTZ camera is easy to install and configure. It can be placed in any place convenient for you: table, wardrobe, window sill, etc. Also, with the help of a bracket, it can be installed on the ceiling. You can configure the camera yourself, read this manual.

This guide shows you how to set up yoosee camera on your phone. To set up yoosee camera on PC read yoosee camera setup on PC

PTZ CCTV camera allows wired (twisted pair) and wireless (Wi-Fi) connections.

A simpler wireless connection will be discussed below.

To use a wireless connection of a smart CCTV camera, you must have a Wi-Fi router enabled.

Unpack the camera

5) a bag with self-tapping screws and tools for resetting settings

Download and install the free Yoosee app on your smartphone (from PlayMarket or App Store)

Launch the app and select “quick registration”. Complete registration. If you cannot register by phone number, complete registration by email by clicking the link at the bottom of the screen “Register with email”

After registration, log in to the application with your email (or phone number) and password (after registration, you will be logged in automatically)

Humidity settings the phone must be connected to the Internet via Wi-Fi.

After entering the application, you will be taken to a page with a list of devices. To add a device, click “” in the upper right corner or in the center of the screen

Select “add a new device”, then click “Smartlink”, then enter the password from the Wi-Fi network and click “next step”

Commentary: If you need to make a wired connection (without using Wi-Fi), then turn on the camera and connect it to the router using twisted pair and then click in the application “wired connection”. In this case, the application will search for cameras connected to your local network. To add a camera, you will need to enter its password (by default, the password is 123)

You will see a page with a message about the need to connect the CCTV camera to power.

Connect the power supply to the CCTV camera and plug it into a power outlet.

After connecting the power supply, the CCTV camera will load (40-50 seconds). Wait for it to end. When the download is complete, the camera will start emitting periodic short beeps, indicating that the camera is ready to configure.

If the camera has booted up, but there are no beeps, this means that the camera was previously configured to connect to a second router. In this case, you need to perform a factory reset. To do this, take a special tool from the bag. Press this device on the white button through the hole at the bottom of the camera. Hold for a few seconds until a single beep appears. After that, the camera will reboot and start emitting periodic short beeps, indicating that the camera is ready to configure.

The location of the reset hole is indicated in the attached instructions.

After downloading the CCTV camera, click “Hear the beep of the dudu” on your phone (while your phone must be connected to the Internet via Wi-Fi).

Next, a window will open in front of you with a message about the need to turn up the phone volume. Increase the phone volume to maximum and position the phone close to the camera to be configured. Click the “send sound waves” button

Your phone will start emitting sound signals, thanks to which the CCTV camera will be automatically configured and connected to the Wi-Fi router. This setting can take from 20 to 100 seconds.

Wait for the end of the automatic configuration. If, after automatic configuration, your phone prompts you for a password from the camera, enter the standard password 123 (the new software version does NOT ask for a password). You will also need to enter some camera name and click the “check device” button.

Now, while watching the broadcast from Yoosee camera, you can turn the camera up, down, left, right. To do this, you need to slide your finger across the screen in the desired direction.

Video recording. Click to record Yoosee camera video. The record will be saved in the mobile phone memory.

Microphone. Press and hold to send an audio message from the mobile phone to the Yoosee camera.

Snapshot. Click to take a snapshot of the image. The picture will be saved in the mobile phone memory.

Speaker. Turning Camera Sound On / Off

To view in full screen, the phone is positioned horizontally and the image is stretched to fill the entire screen

Image quality can be selected in the lower left corner: HD-High, SD-Medium, LD-Low

To record the archive into the camera, you must install a microSD memory card

Go back to the device list. In the upper right corner of your camera window, click the “share” icon. With this function you can open access to your camera to other persons. To do this, you must enter their email or phone number, which they indicated when registering in the Yoosee application.

In the application on the phone, return to the list of devices and click the “settings” button

Here you can change the camera settings: specify the date and time on the camera, configure the archive recording, etc. To set the time correctly, you must specify the correct time zone.

Go to “recording settings”

Manual recording. Manual recording control. On the same line, using the switch, you can turn camera recording on and off.

Alarm recording. The recording is activated when motion is detected or when one of the connected sensors is triggered (door opening, smoke, movement, etc.)

Scheduled recording. Setting time ranges for archive recording.

Press format SD card if the memory card is inserted for the first time or if you want to erase the archive.

For round-the-clock recording, you must select “manual recording” and turn on the “video recording switch”

In this case, the duration of the archive recording will be about 5-6 days when using a memory card with a capacity of 64 GB.

The number of days of archive recording can be increased by specifying the recording time range. To do this, select “scheduled recording” and specify the recording time

To view the archive, go back to the list of devices and click the browse archive button

A list of recent entries will open in front of you. You can name any file in order to view it.

To search for an archive, click the filter icon in the upper right corner and specify the start and end date and time of the archive record that you want to view. Then click the “search” button.

You will see a list of files found in the specified time range.

To view the archive, click on the file you are interested in.

How to set up an ip camera via WI-FI?

When organizing a security system for an apartment, a country house, an office, it is not always convenient to use wired connections. Sometimes you need to configure an IP camera via WI-FI, which will allow you to receive an image from it online directly on the screen of your mobile device. The finished video, compressed to a convenient size, is instantly transmitted over network protocols. Further, with the help of Special programs, it can not only be viewed, but also processed.

Configuration via WI-FI

Working with setting up an IP camera via Wi-fi requires special software on a mobile device or computer. It can be obtained, depending on the type of camera, as follows:

• On the disc enclosed with the purchase. This is not available for all manufacturers’ models;
• Purchase from an authorized dealer;
• Download the camera manufacturer’s website and install it on your computer;
• Purchase dedicated apps for mobile devices.

It is best to configure the ip-camera using the program that can be found on the disk, this will avoid many mistakes.

• To the power grid;
• To a computer using ordinary twisted-pair Ethernet.

expensive models are capable of transmitting both power and picture via a single cable. The ip-camera is connected to a pleasant device either:

• Through a browser;
• Or through software.

Connection algorithm

The step-by-step algorithm for connecting an ip-camera is as follows:

• Determining initially the device’s IP address. Most likely it can be found on the stickers on the box.
• After that, the local network of the computer is assigned an IP address that has the parameters of the same subnet as the camera. To do this, go to the network management tab, find the Properties window there in the Local Area Connection menu, select the Internet Protocol Version 4 option and specify the camera’s IP address in the gateway settings.
• Change camera settings via browser. In the search term of any browser used, the default (general) IP addresses of the camera are hammered. The browser finds it and offers to enter the settings window. Password and login are in the camera instructions.
• When organizing a security system, only one IP camera is rarely used. Each of them will need to assign its own address. This will require some effort and the use of a WI-FI router.

Watching the video, setting up a WI-FI ip-camera for broadcasting over the Internet.

Connecting multiple cameras via Wi-fi router

The cameras are configured in the following way:

• Each of them must get their own ip-addresses. To do this, you need to connect it to the computer, then go to the “Administration” menu. After that, a side menu will appear, in which you need to select the “Configuration” tab and then go to network connections.
• Some routers offer the ability to automatically assign addresses to each individual device. The disadvantage of using it will be the inability to view images from cameras over the Internet. To select an option, tick “DSHP”.
• The camera is more difficult to configure manually. The address of the router is selected, each camera will receive a serial number, which will be put after the dot at the end of the address of the router. In the menu, a fixed addressing model is selected and sequential numbers are entered manually for each camera. In addition, you need to specify the data of the gateway and DNS IP, in both cases it will match the address of the router. The “Mask” parameter contains numbers 255.255.255.0, this is a parameter that determines the address of the subnet host.
• The port number is indicated. Usually by default it will be equal to “80”, if you cannot set it by default, then the number “8181” is written. It is NOT required to enter any more parameters, the columns of the settings window are left empty.
• Click “Apply”, disconnect the ip-camera from the computer and connect it to the router. At the same time, all automatic parameters are restored on the workstation.
• Enter the new address assigned to the camera into the browser. Enter the data of the Wi-fi router’s network into the windows. name and password. Save.
• Reboot the camera and check if it works.

Setting up an IP camera over Wi-fi is easy and takes half an hour. A little more time will be required for the subsequent configuration of the router, in which you need to register the ip-address and gateways of ip-cameras and the name of the used protocol, by default. ТСР with number 1.

We watch the video, connecting the ip-camera to the wi-fi router.

How to set up WI-FI camera

Ready to connect in a new way?

Connect your camera to your Apple or Android device to take photos remotely and effortlessly upload photos worth sharing.

Connect your Canon camera to your smartphone to further expand your capabilities:

• Download images instantly to share them immediately;
• Control the camera remotely from your phone;
• Add GPS data to images captured with PowerShot or IXUS cameras

Frequently asked Questions

Is it compatible with my camera?

Check out the compatibility list below to find out if our software is compatible with your camera.

Or all functions are available on any camera?

No, not all features are available on some camera models. Check out the compatibility list below to find out what features are available for your camera.

How to connect your Canon EOS camera to a mobile device?

Turn on the camera and press the menu button. 2. Select Settings and Wi-Fi. 3. Click the Enable button. If the camera prompts you to register a nickname, do so and then skip the next two steps. 4. Return to the menu screen. 5. Select Wi-Fi Function and set an alias for your camera. 6. Return to the menu screen and select the Wi-Fi function. 7. Select the Connect to Smartphone icon. 8. Select Camera access point mode. 9. Select Easy connection. 10. On the device, select Wi-Fi in the Settings section, select the name of the network displayed on the camera screen. 11. On your smartphone or tablet, go to Settings and select Wi-Fi, select the name of the network displayed on the camera screen. 12. Once the device is connected to the camera’s network, open Camera Connect. 13. The camera will display a message confirming the connection to the device. Press the OK button if prompted to confirm the connection of the device and save the configuration in the SET1 section. Now you can use the program. 14. You only need to complete these authentication steps once. You do not need to repeat them every time. The next time you select the Wi-Fi function, you can use the configuration saved during the initial setup and connect to the camera from your smartphone or tablet by following steps 11 and 12.

How to connect a Canon EOS M3, Canon PowerShot or IXUS camera to a mobile device?

Turn on the camera. 2. Click camera button with mobile phone pictogram. If your camera does not have this button, click the Wi-Fi icon in playback mode. 3. After creating a nickname, select the mobile phone image that appears on the screen. The camera will create a Wi-Fi network to which the device can connect. 4. On the device, select Wi-Fi in the Settings section, select the name of the network displayed on the camera screen. 5. Once the device is connected to the camera’s network, open Camera Connect. 6. The camera will display a message confirming the connection to the device. 7. Now you can use the program. 8. These steps only need to be done once. You do not need to repeat them every time. The next time you press the mobile phone icon button, skip directly to step 4. Alternatively, by pressing the Wi-Fi icon in playback mode, you can access the connection log menu. In this menu, you can select the network name displayed on the camera screen.

How to upload photos from your camera to your phone or tablet?

Connect the device to the camera while Camera Connect is open. 2. In the program window, select the item Images on camera, and all the images saved in the camera’s memory will appear in the program. 3. At the bottom of the program window, tap download and select images to save from camera to device. 4. To save individual photos, select them by touching. If the photo you want is open in full screen, tap the download below it. 5. To save multiple images, click the arrow icon at the bottom of the screen and select the desired images.

What are the advantages of the GPS via Mobile function (GPS via mobile)?

Using GPS data from your smartphone, the GPS via Mobile function adds accurate information such as the time and location to your images. Therefore, by archiving or uploading your images to Flickr, you can always find photos taken in a specific location. GPS via Mobile is available on PowerShot and IXUS cameras.

How to add GPS data to images?

GPS via Mobile is compatible with PowerShot and IXUS cameras.

Make sure your camera and device time is correct. This will synchronize the GPS data. 2. Open Camera Connect and select Location Information. 3. Select Begin logging. 4. Take multiple pictures with your device. 5. Then connect the camera to the device. 6. Camera Connect automatically detects the start of registration and prompts you to synchronize any available information. 7. From the main menu on your device, select Location Information. 8. Select Send location information, then click OK. 9. To view GPS information, select a photo on the camera and press DISP. The coordinates of the location where the snapshot was taken are displayed. 10. To turn off the display of GPS data, select the Location Information item in the main program menu and click the End Logging button.

How to change camera settings in Camera Connect?

To change camera settings, switch to one of the manual modes: M, Av or TV.

Connect your camera to Camera Connect. 2. Select Remote Shooting. 3. A button appears in the lower right corner of the device window. Press it to access options such as Shutter speed, Aperture, ISO, Continuous shooting and Self-timer. 4. Select the setting you want to change and swipe left or right to set the value.

I managed to connect to the program, but the connection to the Wi-Fi network disappears. What to do?

Go to the Wi-Fi settings on your device and select the network the device is connected to. 2. Select network disconnect. 3. Select the name of the network displayed on the camera screen.

How can I get the program on my phone or tablet? My camera was running CameraWindow, but now I am unable to connect it to the new Camera Connect software even though the software is installed. Why?

The pre-connection to your smartphone or tablet using the old CameraWindow is saved on your camera in the connection log. This connection cannot be used again, because it is intended only for the old program on your smartphone or tablet.

If you connected to a smartphone or tablet using the mobile device’s connect button:

Press the menu button and go to the Settings tab (the wrench and hammer icon tab) 2. Select the Mobile Device Connect Button. 3. Clear the Registered destination setting (your smartphone or tablet). 4. After deleting, press the Mobile Device Connect Button again and connect to the smartphone or tablet (be sure to launch the new Camera Connect software on the smartphone or tablet). 5. Once the connection is established, it will be saved to the mobile phone button in the new Camera Connect software, so you can use this button as before. You can also uninstall the old CameraWindow software to avoid confusion.

If you have not used the connection button of a mobile device or your camera does not have such a button:

Select Playback, and then click the Wi-Fi icon button. 2. Establish a new connection by selecting the smartphone icon on the screen, rather than pre-connecting from the connection log. 3. Connect to your smartphone or tablet (be sure to launch the new Camera Connect software on your smartphone or tablet) 4. The camera will then remember this connection in the new Camera Connect and it will appear as a new item in the log. You can also uninstall the old CameraWindow software to avoid confusion.

How to connect using the NFC function?

To use the NFC function, you need an Android smartphone (at least version 4.0) with NFC technology. Turn on the NFC function on your smartphone and then press your camera with it (body parts with N-Mark).

On some models, you need to do the following:

Turn on Wi-Fi in the camera menu and make sure the NFC function is on. 2. On the device, select Wi-Fi under Settings, select the name of the network displayed on the camera screen, and click the Connect button. 3. Tap NFC to launch the program and establish a connection.

My camera has an NFC function that opens CameraWindow. How do I use Camera Connect?

Our Camera Connect software will automatically overwrite the NFC tag.

You only need to connect the camera to the Camera Connect software and click the OK button in the message box with the message about overwriting NFC tag data.

For details on how to connect Camera Connect on a mobile device, see How do I connect my Canon EOS DSLR camera to my mobile device? or “How do I connect my Canon PowerShot or IXUS camera to my mobile device?”

On some models, you need to do the following:

Connect your camera to Camera Connect. 2. Select Camera Setting from the main menu of the program. 3. Click the Start Writing button. 4. Click the camera of the device. 5. After this rewriting will be completed.

How to reset Wi-Fi connections on a Canon PowerShot or IXUS camera?

Press the menu button on the camera. 2. Select Wi-Fi Settings. 3. Select Reset Settings. 4. In response to the request “Reset all Wi-Fi information?” (Reset all Wi-Fi information?), Click OK.

How to reset Wi-Fi connections on a Canon DSLR?

Press the menu button on the camera. 2. Go to the green tab settings. 3. Select Wi-Fi function. 4. Press the information display button. 5. Select Clear Wi-Fi settings. 6. Press the OK button to confirm your selection.

How to leave feedback?

We will be happy to read your feedback on the program. In addition, we would like to hear your suggestions for improving it.

Helpful information

After installing Camera Connect on your smartphone or tablet, you may need to initiate a new connection from the camera to properly connect it to your smartphone or tablet.

Canon Camera Connect has the following features:

[Features and Compatible Models]

1) Wi-Fi connection to camera for image transfer, remote live view and date / time setting.

2) Adding location data of camera images.

3) Bluetooth connection to cameras, it is supported.

[Supported functions: 1, 2, 3]

Powershot SX730 HS, G9 X Mark II

EOS 200D, EOS M6, EOS M5

[Supported functions: 1, 3]

EOS 6D Mark II, EOS 77D, EOS 800D (Remote camera shutter release via Bluetooth available with BR-E1, sold separately)

[Supported functions: 1, 2]

Powershot SX430 IS, SX432 IS, SX620 HS, G7 X Mark II, SX720 HS, SX540 HS, SX420 IS, G5 X, G9 X, G3 X, SX530 HS, SX 710 HS, SX 610 HS, G7 X, SX60 HS, N2, G1 X Mark II, SX700 HS, SX600 HS, N100IXUS 190, 285 HS, 180, 182, 275 HS, 265 HSPowerShot G16, S120, S200, SX510 HS, SX280 HS, N, A3500 IS, A3550 IS, S110IXUS 255 HS, 140, 135, 245 HS

[Supported functions: 1]

EOS 5D Mark IV, EOS 1300D, EOS 80D, EOS 760D, EOS 750D, EOS 70D, EOS 6D, EOS M10, EOS M3IXUS 510 HS, 240 HSLEGRIA HF R86, HF R87, HF R88

Remote live view shooting does not support adding location data to images in the camera via Bluetooth. The size of CR2 images will be optimized for the device depending on the camera being used. Full resolution RAW CR2 file transfer is NOT supported.

Operating system:. iOS 9.3 / 10.3- Android OS 5.0-5.1 / 6.0 / 7.0-7.1

System requirements for Bluetooth:

For Bluetooth connection, your camera must have Bluetooth functionality, and your device must have Bluetooth 4.0 or later (Bluetooth Low Energy support). Bluetooth 4.0-enabled devices iPhone 4s or later, iPad 3rd generation or later, iPod touch 5th generation or later.

Supported file types:. JPEG, MP4, MOV.

• Cannot store MOV files shot with EOS series cameras.
• Cannot store AVCHD files recorded with the camcorder.

Note:. If the software does not work as expected, close it and then try again. Continued use of GPS running in the background can dramatically decrease battery life. When using a Power Zoom adapter, set Live View to On.

Cookies help us make the Canon services and our website the best experience for you. You can learn more about how we use these cookies and change your cookie settings here. To agree to the use of cookies on your device, simply continue to browse our website or click the I accept button.

How to connect a Wi-Fi camera to a router

Perhaps many people have a question about how to connect a wi-fi camera to a router. In fact, everything is very simple. Any wi-fi camera is connected according to the same principle, the first thing is to connect the Patchcord to the router, then through the browser you need to go to its web interface and configure the wi-fi connection. Now let’s take a closer look.

Typically, a new wireless camera has a static IP address. It is usually 192.168.1.108 or 192.168.1.10, but in any case, this IP address is indicated on the stickers of the camera itself or in the documentation. And so, for example, her IP addresses 192.168.1.108, connect her Patchcord to the router. Now look at the IP addresses on your computer, if it has a different subnet, you will not be able to enter the camera settings, that is, let’s say your IP address is 192.168.0.11. Then in this case you need to change the IP addresses on your computer, for example, to 192.168.1.11, leave the subnet mask 255.255.255.0, the rest of the settings are not important. Open the Internet Eplorer browser, it is best to enter the settings through it, because All cameras are designed for at least this browser. In the address bar of the browser, enter 192.168.1.108 and we get to the camera’s web interface.

Perhaps, depending on the manufacturer of the camera, a request may appear to install the activex add-on for the Internet Eplorer browser, I allow and Install. Now you will need to enter a username and password, as a rule, the username is admin and the password is admin, maybe without a password. Here already look in the documentation or on the stickers on the camera. Enter your username and password and then.

The main “screen” will appear where, depending on the manufacturer, a picture will be displayed in real time.

In this interface, there is a button “DEVICE” on top, in some cases there will be “SETUP WIRELESS COMMUNICATIONS” or something similar. Click. The settings window will appear, click on the gears.

First of all, go to the wired network settings to enable the dhcp client (automatically obtain an IP address), you may not need this, but in most cases the dhcp server is enabled on the router to automatically distribute network settings.

Turn on the DHCP client. And press ok. Then the camera can get a different IP address from your router. Therefore, you may have to re-enter the camera web interface settings.

Now, to set up a wi-fi connection to the router, you need to go to network services and select WI-FI.

We put the checkbox on, click OK. Then again we go to WI-FI and click on Search to scan for wi-fi broadcast, then you will see your Wi-Fi network, select it. In the password field, you know what to write =). And if you need the camera to automatically receive IP addresses, check the DHCP box. And click OK.