We independently change the old router to a new one and set up

Any router works and pleases its owner until a certain point. Then, for various reasons, we decide to replace our new old router. For example, this may be due to the fact that a more interesting novelty appeared on the market, the old router began to connect poorly to the Internet or fail, failures appeared during operation and other reasons. It should be noted that such devices are not reliable and durable. Even a simple thunderstorm or a jump in the network can lead to a breakdown of this device. Sooner or later they break and then users of such equipment have a question. whether it is necessary to repair an old router or better to purchase a new one in order to make your life easier. It is often easier to purchase a new router than to repair the old. At the same time, we must not forget that repairs at the cost and time of time may not be a profitable option. Repair can only be done if your knowledge in electronics is much higher than the average level. Otherwise, purchase a new device, connect and configure it. Next in this article we will tell you how to change the old router to another, configure and connect it yourself.

Choose a new router

I must say that the change of old router to a new one begins with the choice and purchase of a suitable unit. The issue of choosing a new device is quite complicated and it must be approached with full responsibility. If you need to change the router in the house for a new one, but it was provided by your service provider, then in this case this issue is best discussed with the technical support of this provider.

Replacing the old router with a new one often begins with the study of the router market. It is best to do this with some popular online store. After all, in it you can study all the technical parameters, see the cost of devices, read the reviews of those users who really use these devices. Replacing an old router with a new is much easier when you know a specific device model. In this case, you go to the nearest store and buy the desired router.

Those points that need to be paid attention to:

your, router, wi-fi, wireless, network
  • Type of connection to the service of the service provider. In the event that your router connects to the Internet network using a network cable or via a modem, you will need a regular device that has a WAN port for the RJ-45 connector. When the router connects to the Internet using a telephone cable, you need an ADSL device that has a connector of the RJ-11 type Connector. When connecting to the Internet through the USB modem, you need a device that has a USB port and support for this particular modem.
  • Data transmission speed. When the Internet speed of your tariff exceeds 0.1 Gbit/s or do you think that over time it will increase, then in this case you should take a router for the house that has gigabit ports that allow you to work at speeds up to 1 Gbit/s.
  • In the case when the purchase of a new router instead of the old is due to the fact that an increase in the radius of the Wi-Fi network is required, or the currently used radio signal amplifier is tired and it is necessary to get rid of it, it is recommended to think about purchasing a device with MESH Wi technology.Fi. The famous TP-Link brand produces quite a few devices that support this technology. In addition, you can always find an alternative to other manufacturers of such equipment.
  • Experts recommend purchasing a router that supports Wi-Fi 5 on radio frequency 5 GHZ (802 wireless standard.11ac “). Therefore, it will be a router that supports work on two ranges. It is better to immediately take a router that supports Wi-Fi 6 (802 wireless standard.11AX “). At the moment, this is the most modern standard of wireless network.
  • When there are many different devices in your apartment or private house, which are connected to the Wi-Fi network, or you like to play online games on your PC, in that case you do not need to save. It is best to take a productive unit for such purposes, which can work without problems even during large loads.
  • Life shows that to purchase a new router instead of the old sellers. After all, if there are any problems (for example, perhaps the device is not suitable, it will be bad to work, etc.D.), you can easily make its replacement with another or return to the seller. An important point. a proven seller will definitely put you the model that will fully satisfy your requests.

Settings plan

So, to make the Internet work successfully through a router, for any model you need to take approximately the following steps:

  • Install a router, connect all the wires, connect the setting device.
  • Roter settings.
  • Internet setting.
  • Setting Wi-Fi.
  • Password change (optionally).

All! But now we will go in more detail for each item in my step.by.step instructions. If something is not interesting or not necessary, just turn over the content of the article to the desired section. But you can first watch the video on the setting:

Installation and connection

We begin to disassemble the primary steps to install a router.

your, router, wi-fi, wireless, network
  • The easiest method for placing a router is near the provider wire. No, I don’t limit you. over, I advise you to first choose a place in the middle of the apartment for the router, and only then ask the provider to start the cable. Another option is to lengthen the cable through the repeaters to the right place. But my universal advice. where the wire fell, put it there.
  • We are engaged in connecting the router. The antennas are removable? Connect. We stick a power supply, and then it into the outlet. Immediately do a check. if there are indicators, then they light up. If not, check the connection again, or the power button on the router (occur on the rear panel). Now it is important that it simply has food and any indication is burning.
  • The best option for the initial setting is to connect through the wire. This will be this item. Those who will connect via Wi-Fi read the next item, but be sure to connect the provider cable.
  • First connect the provider cable. There is Ethernet (like a wire to a computer in size) and a telephone (thin, ADSL). We stick it into the port on the back of the router. The port is usually highlighted in a separate color from the rest. As a rule, blue. Has the inscriptions of Wan, Internet or something like that.
  • We connect a router to a computer or laptop wire to LAN Port (yellow). That’s all. If the connection is successful, we go to the entrance section to the settings.
  • If you want to connect by Wi-Fi, connect. Particularly relevant for those who want to connect on a laptop or phone and do everything through them. Do not forget to connect the power adapter to the network and the provider’s wire. Data for access to the network on a new modem is sometimes indicated on the sticker on the bottom of the device. you can connect through the password and via WPS. Often used just an empty password. Some models do not create a network when setting up.

It does not make a special difference between setting up a router using a computer, laptop, phone or tablet should not arise. The router has a standard web-intake, which will be the same for all devices. Just like your favorite sites.

What should be for continuation: the main thing is to have any connection with the router after these points. whether it is a wire or by air.

Setting Wi-Fi (wireless network) D-Link DIR-615

Now switch to Wi-Fi section.

In setting up a wireless network, the provider does not limit you with some kind of scope, and if you do not orient these parameters, you can contact our specialists for help, or establish the parameters below.

On the main settings tab, you can change the name of the Wi-Fi network (SSID field), the broadcasting channel (if problems arise, the AUTO value can be changed by 6 or 10), as well as the operating mode (usually with the regime indicated by default, there are no problems ).

To save settings, do not forget to press the button to change and go to the next tab. safety settings.

We recommend indicating the following parameters here:

Network authentication: WPA-PSK/WPA2-PSK MIXED clipping PSK: Password for connecting to Wi-Fi, at least 8 symbolswpa-shifting: Tkipaes

Do not forget to save the settings using the Change button. We also advise you to restart the device by selecting the system (right upper angle) in the menu to save and restart.

Support

For entry into your personal account, follow the link. Personal Account.

For authorization, use your login or contract number and password indicated in the contract.

Features of authorization in your personal account:

  • For authorization from the Nevalink network, use your login or contract number and password indicated in the contract.
  • For authorization, not from the Nevalink network, your password should be persistent, t.e. Contain the numbers and Latin letters of the milestone and lower register.
  • If the password is not persistent, you can also log in, however, for your identification, you need to make a call to number 7 (812) 313-41-61. The call must be made from the phone number specified in the contract. The call will be dropped, after which you can go to your personal account.
  • You can clarify which phone number is tied to your contract in the subscription department by number 7 (812) 601-0-701, having passed the standard identification with the operator.

Other authorization methods:

  • account
  • Google account
  • Yandex account
  • Account
  • Account

To use the alternative method of authorization, you must first tie an account in your personal account in the section: add. Services. methods of entering the LC

The password from the personal account is issued when connecting and is indicated in your contract in the act of acceptance and disposal of work.If you forgot your password, then you can drop it. To do this, follow the reference to the password reset and go identify.

Please note that password reset is possible only from your home network!

Also, the password from the personal account can be dropped in the subscriber department by number 7 (812) 601-0-701.

The tariff plan can be found in your personal account. The name of your tariff plan, payment period, as well as the date of the next write.off of the monthly fee, can be viewed in the section “Information”. “Services”

You can change the tariff plan in your personal account or in the subscriber department by phone 7 (812) 601-0-701 daily from 09:00 to 22:00. To change the tariff in your account, go to the “Internet”. “Change tariff” section

You can specify a convenient type of tariff sorting for yourself, or leave the default value

Choose the tariff plan of interest to you. To familiarize yourself with the terms of the tariff, just click the left mouse key to the tariff you are interested in. Make sure that your account is enough money to switch to your chosen tariff

You can check your balance in your personal account.

  • The state of your balance sheet is available on the starting page of the personal account: “Remain in the account”, as well as in the upper right corner in the contact information section under the contract.
  • You can view detailed detail on the balance in the section “Balance and payments”. “History of payments”. If necessary, set the period of interest to you to display.

C 31.07.19 In Nevalink LLC, the Auto Plataeus system (hereinafter referred to as auto payments) is commissioned.Auto Payment is designed to automatically replenish the subscriber’s account according to pre.set parameters from a bank card of any bank settings of the Auto Payment system are made in the personal account of the subscriber.Card details are entered on the bank page and do not fall into Nevalink LLC. After making the payment, Nevalink LLC receives only a masked (hidden) card number from the bank, as well as its validity period for further display to the subscriber. Bank cards data at Nevalink LLC are not stored.Payment occurs through the authorization server of the banking center of the bank using bank cards of the following payment systems:

    It is necessary to add a bank card. To do this, we log in in our

In the section “Auto Payment”. “Auto Plative Parameters”, add the card by clicking the “Add card” button.

After pressing the button, you will redirect you to the page of the Sberbank payment gateway with an initialization payment of 10 after a successful payment you will be redirected to your personal account.Money will be credited to your account. It may take time, a few minutes, to conduct a transaction. It depends on the loading of the system.

Setting up the parameters of the auto payment.

Now you need to choose one of the options for replenishing the account. Reference information from the “Current Services” section will help you to navigate, where services with their cost are presented, as well as the recommended monthly payment.The real amount of payment depends on activated services and discounts and therefore may differ from the calculated.Given the recommended amount for replenishment, we choose one of the three options “Type of replenishment”:

Monthly. replenishment is made monthly on the 25th for a fixed amount. This method is optimal for most subscribers.

If you activate “allow additional replenishment”, then two additional fields will appear.

With additional replenishment, the balance will be brought to the amount of the “brought balance” of the no less indicated in the field, but not exceeding the set values ​​in the “Maximum amount for replenishment per month”.

DHCP functions, search for Wi-Fi networks and reloading the device

The next step is the search for Wi-Fi networks. At the top of the page there is a search button, by clicking on which the user receives a list of networks that is available to him at the moment. Among these items you need to find a network to which the user is going to connect. After entering the password that has already been entered earlier, and the name of the network itself, that is, ssid. After all the manipulations, conservation is also required, otherwise the done will return to the original settings.

Repiter mode assumes that the router will not carry out the distribution of network addresses, so after the actions that were done above, you need to turn off DHCP. That is, without leaving the router settings, to find the “Basic Settings” tab, and then select “Lan Intections” and, entering them, disconnect the DHCP server. And before moving on to the next steps, you need to save actions using a button at the bottom of the screen.

After these actions, the device is likely to “think” for about five minutes and will reboot itself. Some models, depending on the firmware, requires a reboot from the user: if the settings are correct, but the device continues to be in the same mode, you need to do it yourself. However, most of the devices asks not to turn off the device and wait until it independently completes the necessary settings: for this, the adjuster does not need to do anything.

After forced or ordinary rebooting, it will be necessary to enter a login and password that at the beginning of the adjustment process the settings already recalled: this is the data that are entered at the time of the first use of the router either by the person himself or the programmer setting up the device. It also happens that reconfigure occurs without re.entering this data, so you should not worry if the router has not requested the password again: in this case, the data already loaded is enough.

Final checking check and connection speed

One of the last steps is to check whether the manipulations described above have been carried out correctly. For this you need:

  • To enter the router settings through the computer browser repeatedly, as has already been done earlier;
  • In the settings, find the “Status” tab, and go to “Wi-Fi settings”;
  • The “state” column should appear “Connected”, and this means that the router is already connected to the access point necessary for further transmission of the signal, that is, the manipulations were done correctly.

Setting up the Upvel router requires checking whether the device takes the desired channel: for this you need to open the page in the browser and look at whether the site is loaded. If so, then, then, the device has become a relay and that it takes the signal of the remote access point, and the adjustor performed actions, in accordance with the instructions. There are also other options for checking the connection. For example, Ping, Tracert, Pathping for those who love CMD, but these methods of interaction are more often used by professionals.

If the adjustor is sure that everything did the right thing, but the router did not become an access point, you need to do the sequence of actions again: perhaps, in one of the stages, the device was loaded for too long, and “did not have time” behind the user, which has already moved to the next settings stage. In this case, everything should not be done quickly, giving the device the time to “think”, especially if the device is not new, because it worked actively earlier.

As a result, since the Upvel router has become a repiter, now you can connect the rest of the Wi-Fi receivers and adapters that will take a signal using a twisted LAN resetelated pair in the WAN of access to the network to which the connection was connected to which. In order to configure the rest of the routers as a “unit” of a newly connected ranger, they should work in the “gateway” mode, and also not be able to join other networks, except for the user.

How to Set Up a Router | Internet Setup

After that, you should look at the speed of the access point to which the relayer is connected, as well as the rest of the devices in the “network” formed: if its speed is low, then, respectively, the pages will not be loaded quickly, because the Internet is now distributed to all points the same way, and is unlikely whether it will happen that in one of them the connection will be faster, and in the other slower.

If you want the Internet pages to be loaded in excess of the entire coating area, then you need to choose a speed point of access initially.

The devices connected to the “unified system” also have one feature: since they are included in a single network, you can enter any of them from each network device, which will be connected to any of the network access points. To do this, you will need to know the IP address of the router, as well as the main parameters, that is, the login and password. Some users need this information.

Change the password to enter the router settings (administrator password)

Putting the password only on a wireless network is not enough. It is equally important to protect the router itself. The standard password for entering the router settings indicated on the lower panel is usually too simple. Outsiders can guess it. To prevent this from happening, come up with a more complex combination.

You can install a new password in the settings section called “system”, “device”, “system tools” or in a similar way.

Install the router in the optimal place

Put the router as close to the center of the zone in which you want to use Wi.Fi. Then the signal will be approximately equally available to all connected devices.

If possible, consider physical obstacles. The smaller the walls, furniture and other objects between the device.receiver and the router, the better the wireless network works.

This material was first published in February 2017. In April 2020, we updated the text.

Additional other settings

Some models that differ from TP-LINK provide for the possibility of detailed settings for the wireless network parameters. The following is a detailed instruction what and how is set up from the personal account on the provider’s website.

  • When choosing a “main settings of the wireless network”, a window will open, which contains the subparagraphs “Standard”, “Canal”, “Signal power”, etc.D. (cm. photo below). But are of interest to the user in this case “standard” and “signal power”. “Standard” determines the maximum network speed. The fastest. standard 802.11AS, but it is not always available for choice, but, if available, may not be supported on some devices. An alternative to him can be 802.11n. it is slower, but insignificant. Among other things, it is supported by absolutely all modern devices.
  • Some modern routers have a built.in second range, in which another wireless mode is available: 5 GHz, in addition to standard 2.4 GHz. The frequency of 5 GHz is always an order of magnitude more unloaded, due to which the data transfer rate on it is much higher. However, due to a faster transmission, the radius of the coating is seriously reduced, and not all devices support the range of 5 GHz. In such routers, both modes can be included simultaneously. The main thing is not to forget to put the password on both frequencies.
your, router, wi-fi, wireless, network

Additional firmware update

Routor manufacturers regularly produce software updates for devices to increase work stability, degree of protection, as well as data transfer speed. Such an update can be installed without problems yourself. The following descriptions are described to update the firmware for the example of TP-LINK.

  • Having entered the official TP-Link website, the user will have to find the necessary device. Then go to the “Built.in software” tab, as shown below, and download the latest firmware version. Or in more modern models, to do it directly in the web-integer router.
  • Next, you will need to connect the router to the computer on which the update file is downloaded via Ethernet Cabel, and go to the device settings (see. Step 2). Then select the “System Tools” item and find “update of built.in software”.
  • The installed versions of the current built.in software and equipment will be shown here. You need to select a file downloaded earlier and wait for the end of the installation. Nothing complicated.

All is ready. Now you can set up a router for a new provider yourself. And if you have any questions. please write in the Комментарии и мнения владельцев. I will help everyone.

What to do if you can’t enter the settings?

Most likely, the problem is that the address or login/password is changed and standard information that is used in the initial purchase and configuration of the device. For this reason, standard data is simply not suitable.

In this case, it is recommended to reset the settings to factory. This can be done by holding (no more than 5-10 seconds) discharge buttons. The indicators at the same time blur and restart. After that, the router will be rebooted and you can try to again enter the default data to enter the settings page.

Firmware update

See the recharge instructions in the following

As promised, I write details. Here is a step.by.step instruction:

  • We are looking for a version of the firmware on the router itself. In the same place where the address is written, login and password. For example, you have written 8.one.
  • We go to the officials, to the site TP-Link TP-Link.com. Looking for firmware for your version 8.
  • At the bottom of the page we are looking for the section “Built.in software” and download ourselves the very first firmware on the list.
  • Unpack the archive and pull out the file with the extension.Bin. this is a file with firmware.
  • We go to the router’s admiral admission to the “System Tools. Firmware Upgrade” section. Select our file with firmware and click “Upgrade”. We are waiting for the end of the installation.

Important! We make the firmware update exclusively through the cable! During the installation of the file, do nothing. After installation, the router will reboot itself.

Modem vs Router. What’s the difference?

As you can see, there is nothing difficult to set up. By the way, for him you can look for a Russified firmware, in the same place. on the official website. Then the settings will be even easier.

Adsl, Ethernet, USB

I repeat once again that all routers are built approximately the same. There is only a small difference in the technology of establishing the connection: through the ADSL telephone cable, through Ethernet, through the USB modem.

Everywhere the introduction of a login and password from the provider will be required. If there are any doubts, still find a review for your model. Here for full lighting I will take the ADSL modem. the settings in the connection there are a little more. So when using a modern cable you will have less possible problems.

It doesn’t matter which operating system you use-Windows, Linux, Mac OS, iOS, Android, or something else. Settings will still occur through a browser on a web-integer.

Internet setting. just

Any modern modem is now supplied with a convenient setup master, and besides in Russian. I have now written in my model. “Fast Settings”. Everything is really shown and told, right for dummies there really. Therefore, I will not stop there wide here, I will simply give a step.by.step instruction, what he usually does:

  • Welcome you.
  • Asks to find out how you want to use the modem-we put something like “connect to the Internet”.
  • He will ask how you want to do this. they usually choose pppoe mode.
  • Enter the login and password from the Internet provider.
  • Usually here he asks for activation of the Wi-Fi network. Asks to create a password for her.

Sometimes a special disk comes with a router. Usually there are no drivers on it, but there is a software setup master. Differences from the web-integer are minimal.

And all! All settings. Continuously further-and-next. So then I will show a little more on the old modem with screenshots. Suddenly you need to use this. What is cool. all TPLINK models somehow have a very similar integer.

Manual configuration

Setting up the Wi-Fi-Roatter of the TP-LINK N300 model begins with changing the network parameters:

  • In the navigation menu, open the section “Network”.
  • Select the subcategory “WAN”.
  • If your connection provider uses DHCP, then you need to select the “Dynamic IP” parameter. Such routers are connected to the provider’s nodes automatically to get the desired configuration. In this case, no information is required to enter, just click on the “Save” button.
  • If static IP is used, then you need to select this option in the “type of connection type” section. It is necessary to specify the IP received from the provider, a mask (255.255.255.0), the main gateway, primary and secondary DNS. Separately, consider the parameter “size mtu”. This function is responsible for the size of the transferred data packets. It is recommended not to change the parameter if this is not necessary.
  • Press “save”.

PPPOE settings

Many people ask how to connect a wireless TP-Link router to the Internet. You can do this after changing the parameters of the tunneling protocol:

  • In the navigation menu, open the “Network” tab.
  • Select the option “WAN”.
  • In the “WAN connection type” section, specify “pppoe/
  • Enter the user name and access key received from the provider.
  • At the “Secondary Connection” item, mark the Chekbox “Disable”.
  • In the section “Wan connection mode” Select “Connect on request”.
  • Specify the maximum downtime 10 or 15 seconds.
  • Click on the “Save” button.

The local network

Setting up the local Wi-Fi network is also a mandatory point. See step.by.step instructions further:

  • Go to the “Network” section.
  • In the dialog box, select “Local Network”.
  • The MAC address paragraph will display the physical address of the LAN port.
  • In the IP Address section, indicate the IP of the wireless router “192.168.0.one”.
  • In the tab “Mask subnet” write “255.255.255.0 “.
  • Click “Save”.

Wireless mode

To ensure connection to the network, you must correctly set the parameters for the access point:

  • Open the “Wireless Main” and “Wireless Settings”.
  • Indicate the name for the access point “SSID”. The name can be any. It is allowed to use letters, numbers and punctuation marks.
  • In the drop.down list, select the region of residence. Only the country is indicated.
  • In the paragraph “mode” indicate the value “802.11 b/g/n mixed “.
  • In the section “Channel Width”, indicate “Auto” or “40”.
  • In the Channel tab, select one of the available. Please note that 1,2,3,4,5,6,7 and 8 most loaded. Most devices work on them in your apartment building. It is recommended to use 9, 10, 11 and 12.
  • Select the maximum data transfer speed.
  • Mark the checkboxes “Turn on the broadcasting of SSID”. Thanks to this, your gadgets will be able to determine the access point.
  • Click “Save”.

Encryption protocol

Here we are and moved to the last point of manual settings of the router. It remains to indicate the parameters of the encryption protocol. It is on this that the safety of your confidential data will depend:

  • In the navigation menu, select “Wireless mode”.
  • Open the subparagraph “Protection of the wireless regime”.
  • It is recommended to use the type of encryption “WPA2-PSK/WPA-PSK”.
  • At the point “Version” select “Automatically”.
  • In the “Crystation” section, indicate “tkip”.
  • Come up with access key.
  • The parameter “The period of zeroing of the group key” is left unchanged.
  • Press “save”.

Roter reconfigure

If you purchased a router from your hands, you must reconfigure the wireless regime in accordance with the technical recommendations of your provider.

Reset

  • Turn the modem and find a button with the name “Reset”.
  • Using a sharp object, hold a button for 10 or 15 seconds.
  • The indicator of the router will go out and after a few minutes is activated again.

Now the device is ready for reconfigure. We need to change only the parameters of the wireless regime.

We change the configuration of the wireless regime

How to reconfigure a router, see further:

  • Open a web browser and write an IP device in the address line.
  • In the form of entering the login and password, indicate the accounting data.
  • In the navigation menu, select the “Wireless Mode” tab “.
  • Click “Wireless Settings”.
  • Indicate the name of the access point.
  • Select the region of residence in the drop.down list.
  • In the paragraph “mode” indicate “11 b/g/n mixed”.
  • The parameters “Channel width” and “Canal” can be left unchanged. If you decide to install your settings, then use only 40 mhz width.
  • Select data transfer speed and mark the Chekbox “Turn on the SSID broadcast” and click “Save”.
  • Open “Protection of the Wireless Regime”. Mark “WPA2-PSK”.
  • Select the version “WPA2-PSK”.
  • In the “Crystation” point, indicate “tkip” or “aes”.
  • Come up with a password and click “save”.
BYRGPUB.COM 2022