In the plafond of room lighting

In some cases, the installation involves the installation of the device in a ceiling light. This method is characterized by the following features:

• Provides additional protection.
• Viewing angle ensures safe reverse parking.
• Install the camera in a location that is least likely to be hit.

This installation location is the most commonly used location. Modern devices for receiving a video signal are small, so they can be placed in the plafond of a room lighting device.

Into the bumper

Some motorists, when independently carrying out work, provide for the possibility of installing the device in the bumper of the vehicle. Among the features of this installation site are the following:

• The device is exposed to many different influences.
• The possibility of mechanical damage is not excluded.

In the case of Renault Duster, the camera installation procedure is simple due to the high ground clearance. To do this, it is enough to drill a hole and install the devices, securing it using various methods. If we install the camera in the bumper, you should provide high-quality and reliable protection.

Pulling the wire

After the camera has been installed, proceed with the cable installation. This work is characterized by the following features:

• The cable is stored under the rear door trim. For this, the casing is removed, which is attached with screws and rivets.
• The cable is fixed with tape. This increases the reliability of the connection. After that, you can re-install the cladding.
• It is possible to lay a cable between the rubber seal and the body. This will significantly increase the degree of protection of the cable from environmental influences. The wire connected to the device must be handled with care, even the smallest defect is not allowed.

When working, you need to be careful, because applying great effort, you can damage the skin itself.

How to install a rear view camera on a Renault Duster with your own hands

When driving on busy roads, many parking difficulties can arise. This is due to the fact that the rear-view mirror provides a narrow viewing angle, so it is difficult to fit the transport space into the required position. The modern solution of automakers is the installation of a rear view camera. It has a wide viewing angle, transfers the image to the display. Do-it-yourself installation of a rear view camera on a Renault Duster is carried out to increase safety.

Connecting the camera to a radio or image output source

After laying the cable directly, you should proceed to connect the camera to the display.

It should be borne in mind that during installation, removing the battery becomes the reason for blocking the radio.

After that, you will have to enter the unlock code. Among the features of the procedure, we note the following:

• Special adapters are used.
• High-quality connection requires the use of insulation.
• The joints must be protected from vibration and other influences.

At this stage, mistakes are rarely made, but problems may arise with the selection of a suitable adapter.

Connecting to the head unit

The stage of connection to the head unit is carried out after most of the elements of the system are located in their places. In this case, a connection is made with the head unit and the camera itself. Features of the work carried out are in the following points:

• The head unit is connected using connecting plugs.
• To trigger the camera at the time of switching on the reverse gear, it is connected to the lamp.

There are a large number of different adapters on sale that increase the quality of the connection. At the moment of movement of the vehicle, strong vibration may occur, it negatively affects the quality of contact.

Camera selection

A video camera for Renault is purchased taking into account the features of the vehicle configuration. A standard camera can be of several types:

• Mortise. Such a camera of the Duster type is the most common, since it is installed inside the car and is protected by a housing.
• Overhead. This version is bolted to the license plate light. This installation method is simple, but the device is not protected from environmental influences.
• On the frames. Mounting in this case provides for the installation of the device in the license plate frame. A rear view camera is installed on the car only taking into account the fact that operation is not possible in all weather conditions.
• On brackets. These models are located inside the passenger compartment directly next to the glass. Location inside the vehicle increases the degree of protection of the device from environmental influences.

For Renault Duster, you can purchase an original device, which is supplied for sale after the vehicle has been disassembled. The main selection criteria are the resolution of the resulting image, viewing angle, the presence of backlight and some other points.

So to your attention detailed instructions on how to install a rear view camera

In my car, I used the RM116B camera model, it’s not critical, you can choose another one according to your taste. It is best to place the rear view camera closer to the license plate light bulb, slightly drowning it in the body of the bumper, away from eyes.

The easiest way would be to install a rear-view camera near the room lighting lamp, on a plastic rim, but in this case it will be visible and against the background of white numbers it will stand out strongly.

Taking into account such features, I decided to “push” it deeper into the bumper directly above the license plate. that is, into the bar that holds the lighting lamps. In short, now there will be no problems with the holder, which is already good, the mount will be hidden and there will be no need to pick the bumper. In order to repeat what has been done, you need to empty the luggage compartment and remove the frame with numbers.

Dacia Duster rear cam installation

You need to withdraw through the left hole, so that the length of the wire is enough.

Due to the deep location of the ramp, the leg of the rear view camera had to be slightly modified by lengthening it. Perhaps this will be superfluous for your camera model. In my case, the issue was solved by simply using a metal plate of about 4×6 cm.

Installing a rear view camera is also unpleasant because you have to mess with the wiring. I advise you to pull it into the luggage compartment using a plug or a hole in the area of ​​the rear bumper or spare wheel.

Now it’s time to start the installation work and connect the camera to the monitor, as well as wiring in the car.

First of all, remove the decorative trim for the trunk sill and the left side of the trunk trim, then remove everything unnecessary from the passenger compartment: seats, mats, door sills, etc. You will need access to the rear of the radio, so remove it and carefully study the connectors.

I took the positive wire from the left rear headlight, my wire color is white with a red stripe, it is connected to the lamp. The connection itself was made a little further so that it was less noticeable. I am attaching the connection diagram, so there should be no problems.

In the area of ​​the torpedo, I found a “plus” from the reversing light.

Next, you need to act very carefully, laying wires is a troublesome business. Using the “native” fasteners and clips. When the wiring is laid, do not rush to collect everything, first check the operability and correct connection of the equipment. I don’t need to tell how to test, I think everyone understands that if there is a picture and everything works fine, then the camera is installed correctly.

If the test is successful and the rear view camera works correctly, adjust the position of the camera and proceed to assembly in the reverse order.

I adjusted the lens a few days after installation, it is quite difficult to do it right away, because it is not clear at first how and where exactly the camera should look. Approximate angle of view is. 120 °.

Do-it-yourself installation of a rear view camera. instructions

The rear view camera is perhaps one of the most controversial tuning elements that motorists constantly argue about. According to some, the installation of a rear-view camera is meaningless and refers more to “show-off” and “bells and whistles” rather than useful assistants that drivers use every day. Others consider them a vital element, as well as the most useful invention after the car, and regularly use them when parking, or leaving (driving) to the garage.

Renault Duster Reverse Camera(Media Navigator) Installation

In my opinion, opponents of the rear view camera. These are the so-called “Old Believers” drivers, these are experienced drivers who do not accept any innovations and useful options, they are “brutal” and use only a rear-view mirror. For them, the car has remained just a means of transportation, and they do not want to keep up with the times, therefore, they do not accept anything new and making life easier. Personally, I think that everything that the owner does with his car is his own business, in addition, if it helps him live or drive a car, then why not? Better a rear-view camera than the innocent face of some lady who drove in your backside or side with the words: “Oh, I miscalculated a bit” or “I’ve only been driving for a month and I don’t know how to reverse.” My article today is for those who are racking their brains over how to install a rear view camera with your own hands. I will try to tell you in detail how to do this, supporting each step with informative photos.

Afterword.

Installing a rear-view camera is not important with your own hands or in a service. this is a significant saving of money, an opportunity to gain invaluable experience, and the joy of doing your own work. Try it, maybe you will come out even better than me, as you can see in my case it came out pretty decent too. For those who doubt it is worth it or not, I will answer. it is better to spend money once and “sweat” over the installation of a reversing camera, rather than constantly “steam” in tight parking lots and pay for your own and others’ repairs.