Entering BIOS on Lenovo laptop

Probably, there are no PC users who, at least once during the entire time of their work with a computer, would not need to enter the BIOS. Those who use Lenovo products did not stand aside either. This manufacturer has a huge list of laptops, and not all of them can enter the BIOS in the same way, but it is easy to configure it. the functions are the same everywhere. Today we will try to figure out how to enter the BIOS in a lenovo laptop, be it Lenovo s9, Lenovo z50 or Lenovo b50.

enter, bios, lenovo, laptop

Why is there a need to enter BIOS on Lenovo at all? Even despite the fact that laptop manufacturers in each new released model try to minimize the requirements for PC knowledge from the user and give the simplest answer to the question of how to set it up or determine the cause of problems, sometimes it becomes necessary to fine-tune the parameters. What you can use this input for:

  • Turning on and off some of the hardware parts of the laptop, diagnosing problems;
  • Configuring boot parameters for the OS and the entire device;
  • Setting up the disk subsystem, in particular, the modes of its operation;
  • Customization of many other functions, parts or system in general.

lenovo boot key & Bios Setup

How to enter BIOS of Lenovo laptop: method 1

The manufacturer Lenovo has created its own software called Lenovo One Key Recovery, a system that includes the ability to back up and restore data to Lenovo PCs. In order to enable it, there is an additional button on the laptop. Novo. It is found on almost all the latest laptop models from Lenovo and is located either on the side of the case or near the power button. Sometimes, in the most modern models, there is a small hole inside which there is a microswitch. In this case, you need to use a thin, non-sharp object. for example, a paper clip.

And despite the fact that the direct purpose of this button is not to call the BIOS, you can still get into the BIOS using it:

  • Turn off the device by holding down the power key for 10-15 seconds;
  • Hold the Novo key for 2-3 seconds and release;
  • Your laptop turns on and opens a small menu with a choice. click on the line with the signature “BIOS Setup”.

How to go to BIOS on Lenovo laptop: method 4

If you have Windows 10, then there is another way to boot the BIOS, similar to the previous one. Here it is carried out in a slightly different way:

  • In the “Start” menu, click on “Options”, select “Update and Security”;
  • Open the “Recovery” tab and click on restart under the “Special boot options” label;
  • The device reboots, and we see an action selection window. After you enter the desired menu, do the same as in the previous paragraph when starting BIOS on Windows1.

enter, bios, lenovo, laptop

If, when using this or the previous method, you did not see the “UEFI Firmware Options” button on the screen, this means either that this laptop has an outdated BIOS version without UEFI, or that the OS was installed on the laptop in Legacy mode. Then work with UEFI is not available from the operating system. you will have to use the first two methods.

Entering BIOS on Lenovo Laptop: Method 2

Entering the BIOS on a Lenovo laptop is carried out in several ways. unfortunately, there is no single solution for how to get into the BIOS for everyone, but the ways to start it are quite simple. So, let’s move on to the first method.

The most popular solution is to use a keyboard. pressing several buttons at the same time on the laptop immediately after starting it up. Turn off your laptop (this method will not work with enabled), then press the power button and immediately one of the options:

  • F2 button or Del button;
  • Combination FnF2;
  • F1 key

If the BIOS was launched incorrectly, the computer will boot the OS normally. In this case, you will have to turn it off again and call the BIOS again, but using the new boot method. In order not to play the “guessing game” and start the BIOS faster, you can also look at the instructions for the Lenovo laptop.

It also happens that the laptop starts up too quickly, and the user does not have time to press the required combination. To avoid this, turn off the laptop by holding down the power key for 10-15 seconds. Then hold down the desired combination to enter the BIOS, and then press the power button and release, while continuing to hold down the keys to enter the BIOS until the desired screen with parameters appears in front of you.

How to enter BIOS of Lenovo laptop: method 3

Around the same time that a new BIOS version called UEFI was released, the new Windows 8.1 operating system was released. And along with it, a new way of loading BIOS appeared. through the OS:

  • First you need to go to your desktop. Then we call the side menu of the Windows desktop. to do this, move the mouse cursor to the lower right corner of the desktop. Select “Settings”. “Change computer settings”;
  • Then go to the menu item “Update and recovery”, and then under the line “Special boot options” press the restart button;
  • After the reboot has been completed, we get to the screen with the ability to select an action. Click on the “Diagnostics” tile and then on “UEFI Firmware Settings”;
  • Confirm the selection by clicking on the “Restart” button. Done, the laptop entered the BIOS!

enter, bios, lenovo, laptop

How to enter BIOS: method 5

The last method is the most radical, and can only be recommended to those users who already have good experience in disassembling such a device. Otherwise, you run the risk of irreparably damaging your Lenovo laptop.

The essence of the method is as follows: to reset all BIOS settings, you need to disconnect for some time a special CMOS battery that is connected to the motherboard of the device. After performing this action, the device will “think” that the settings may be incorrect and will prompt you to open the BIOS to correct them, or it will enter it on its own.

enter, bios, lenovo, laptop

BIOS batteries look different and in almost every model each has its own place, so you have to dig around before you get to it and unplug it. But in general, the procedure is as follows:

  • Disconnect the laptop, remove the battery;
  • Access the CMOS battery and carefully disconnect it from the motherboard;
  • Wait 15-20 minutes (this is necessary so that the CMOS chip is de-energized and the capacitors on the motherboard are discharged);
  • Connect the battery back, assemble the laptop, plug in the power and turn on the device;
  • If you did everything correctly, you will see the BIOS settings screen.

We hope that one of the above methods helped you find the answer to the question of how to enter BIOS on a Lenovo P70, G50-80, Lenovo ThinkPad T400 or T440 laptop.

How to enter BIOS

Notebook BIOS entry methods may differ on different Lenovo models. First, try the standard login method. when you start a personal computer, you need to press the F2 button on the keyboard, sometimes holding down the Fn key before that. Next, the PC parameters menu will be called.

enter, bios, lenovo, laptop

But this method is not always working. For some Lenovo models, the BIOS does not load when you press F2 or FnF2. for example, Lenovo Legion Y520, Lenovo G70, G50-30, or G500. If you tried to enter the BIOS using the above method, and you did not succeed, the following instruction is for you:

  • On the side of the laptop (where the charging socket is usually located) or right next to the power button, there should be a special small key with a curved arrow. It’s called Novo Button, One Key Recovery, or One Key Rescue System. You need to turn off the laptop and click on it.
  • If you pressed the correct button, the laptop will start, and on the screen you will see that we are going to a special startup menu:
  • Normal Startup
  • BIOS Setup (parameters);
  • System Recovery
  • Boot Menu.
  • As you probably already guessed, in order to enter the BIOS on Lenovo, you need to go to the BiosSetup item. After you select it, you will see that the laptop entered the BIOS and you can configure it as you like.
READ  Lenovo g50 30 how to enter BIOS

How to enter BIOS on Lenovo computers?

Lenovo is one of the largest computer companies in the world. And since the demand for the products of this company is growing, the questions about the correct operation and operation of Lenovo equipment are becoming more and more relevant for users. And for those who decided to reinstall Windows, at the very beginning of the process, the question is raised: how to enter Lenovo BIOS?

First, you need to figure out what BIOS is and what it is eaten with. So, BIOS on Lenovo is a special microscopic program that ensures correct and stable interaction between all components of the PC and OS and allows you to customize it. And the BIOS setup is a standard PC setting that helps the system calculate the functions that should be activated and how they should be loaded. BIOS is on any computer, be it Lenovo B560, Lenovo S21 or M5400.

To date, several different versions of Bios have been created, which differ slightly in appearance, but as for the functions, everything is identical here. Each of the versions is used for the initial setup of the computer and for testing it. BIOS functionality includes:

enter, bios, lenovo, laptop

  • Date and time setting;
  • Selecting the boot sector. the device from which the operating system will be installed or loaded;
  • Checking system components, including checking the health of RAM and hard drives;
  • Connection protection. password on your laptop to protect personal data.

Two secrets to running BIOS

But if you still did not manage to start the BIOS using one of the above methods, and the laptop has Windows 8.1 or higher operating system, we will tell you two startup secrets.

enter, bios, lenovo, laptop

  • You need to turn on the PC. In a running computer on the desktop, drag the mouse pointer to the lower right corner of the desktop (call the side menu).
  • A menu opens to us, where we select the items “Options”. “Update and Recovery”. “Recovery”.
  • Here, in the “Special boot options” section, click on the “Reload now” button.
  • Next, a blue screen with tiles will open. Open the “Diagnostics” tile, by clicking on which you will be taken to additional parameters.
  • You need to open the item “UEFI Firmware Options” and click the “Restart” button. Ready! You are in BIOS!

Second secret. Many Win 8.1 users make an error when trying to enter BIOS. Everyone knows how to get into the BIOS. you need to press a certain button on the keyboard. To do this, the user clicks on “Shutdown”, waits for the laptop to turn off, and then presses the button to enter the BIOS, but the computer starts in the old way. the OS is loading.

The whole problem is that the Windows 8.1 operating system works initially with the fast startup function, which is based on sleep mode. enter the BIOS without turning off the PC, but restarting it.

Some helpful tips:

enter, bios, lenovo, laptop

  • After entering the BIOS, go to the various settings of the system parameters and its boot in the BIOS itself. Be very careful and careful, and it is better not to touch what you do not know, as there is a risk of doing something wrong and completely losing your computer. After making all the changes, go to the “Exit” section and select “Save exit”. After that, the laptop will be restarted, and on a new start, all the settings that you had to set before will already be taken into account.
  • If the above methods of entering BIOS on a Lenovo laptop do not work, try holding down the F12 key while starting the device until the BIOS starts. this method works on some Lenovo models.
  • It is very rare, but it still happens. in some models the F1 key works (you need to press it several times while the laptop turns on).
  • Manufacturers recommend adjusting PC settings in BIOS only with a fully charged laptop battery, since if during the setup process your laptop turns off due to being discharged, then this is likely to cause some system problems in the future.
  • Before exiting BIOS, be sure to save all changes so as not to get lost.

Remember that BIOS setup is a very serious undertaking that requires maximum understanding of the process and great attention to detail. You should be aware that if the configuration is incorrect, some components of the system may not work correctly, which brings additional difficulties in operation. And if you doubt that you know how to do it right, it is better to call qualified specialists, this will save money, time and nerves. We hope this article helped you figure out how to enter BIOS.

LENOVO Notebook BIOS Entry Options

As for entering the BIOS of Lenovo laptops, the methods are quite diverse and the choice of one or another method depends primarily on the device model. There is no one-size-fits-all solution for all Lenovo devices, but often multiple methods work successfully on the same laptop. They can be used alternately or you can choose the one that seems most convenient.

Windows 10

In the newest version of the Windows operating system, the ability to reboot to UEFI using the “Special Boot Options” screen was inherited from Windows 8. Only the “Computer Settings” window is opened differently.

    Press the Settings button in the Start menu.

Or open the notification panel by clicking on the icon in the lower right corner of the screen, and press the button “All parameters”.

In the “Windows Settings” window that opens, select “Update and Security”.

In the next window, go to the “Recovery” tab and click the “Restart now” button in the “Special boot options” section.

A reboot takes place, and we get to the “Select action” screen.

Optional: For a quick reboot to the diagnostic and system recovery screen, you can use the command line (this method also works in Windows 8 / 8.1).

    We launch the command line on behalf of the Administrator by right-clicking on the “Start” button and from the menu that opens, selecting “Command line (Administrator)”.

  • A reboot will occur within 60 seconds.
  • Further, by analogy with the steps in Windows 8: “Troubleshooting”. “Advanced options”. “UEFI firmware options”. “Restart” button.
  • How to enter BIOS on a lenovo laptop

    Almost every user of a modern laptop at least once during the operation was faced with the need to enter the BIOS. Users of Lenovo solutions did not stand aside either. The manufacturer has a very wide range of laptop computers, which entails a variety of methods for performing certain operations, including procedures for entering BIOS settings. Let’s try to collect all the ways together.

    When does it become necessary to enter BIOS on a laptop? While Lenovo strives to provide its users with a superior product that will require a minimum level of service and hardware configuration knowledge from the user, it is important to understand that no laptop is immune to the sudden onset of critical errors and crashes. At such moments, you may need to adjust the parameters.

    If we disregard the idle curiosity of some owners, then entering the settings of the basic I / O system is a necessity when:

    • enable / disable certain hardware components (touchpad, network card, USB controller, sound processor, etc.);
    • setting up the operating modes of the disk subsystem;
    • choosing boot options for devices and operating systems;
    • diagnostics of hardware components;
    • setting many other specific parameters (depending on the specific configuration of the device) of individual components and the entire system as a whole.

    Keyboard shortcuts

    The most common and frequently used way to enter BIOS settings is by pressing a specific key or key combination on the keyboard, immediately after turning on the device. On the switched off laptop, the power button is pressed and, almost immediately, we press one of three options:

  • In very rare cases, on older Lenovo notebook models, the F1 key is used.
  • Common mistakes when using the method

    • In most cases, after pressing the keys, the expected loading of the BIOS setup screen does not occur due to an incorrectly selected key / key combination for entering. It is worth trying all of the above keys and combinations in order. To reliably find out which key or key combination is exactly right, you need to refer to the documentation for your particular laptop model. You can find and download it on the official Lenovo technical support website.
    • In addition, the failure may be due to the ultra-short delay between the initialization of the laptop’s hardware components and the start of the operating system loading. The user simply does not have time to get into this short period of time and the keystroke is not processed by the system as needed. In order to exclude this option, you can try the following:
    • Turn off the laptop completely. To turn off completely, you must hold the power button for 10-15 seconds.
    • First, press and hold the BIOS entry key or key combination.
    • We briefly press the power button and do not release the enter key or key combination until the screen with BIOS settings appears.
    READ  Lenovo ideapad s145 installing Windows 10

    Windows 8 (8.1)

    The release of the Windows 8 operating system almost coincided with the massive introduction, including into Lenovo laptop computers, of the new BIOS version. UEFI. For users, the new version of the basic I / O system brought a lot of interesting features, including a new way to enter the BIOS. reboot from the OS.

      In Windows 8, we call the “Computer Settings” window. To do this, you can open the side panel on the desktop by moving the mouse cursor to the lower right corner, click the “Settings” button, then click on the inscription: “Change computer settings”.

    Or, on the initial screen of the Metro interface, click on the button with the gear icon.

    In the “Computer Settings” window, select the “Update and Recovery” tab.

    In the “Update and Recovery” section, click “Recovery”, then under the “Special boot options” label, click on the “Restart now” button.

    After rebooting, the Select Action screen appears. Here you need to click on the “Diagnostics” button.

    Go to the section “Additional parameters”.

    Click the “UEFI Firmware Options” tab.

  • We confirm the reboot into UEFI by clicking on the “Restart” button and the BIOS settings screen appears in front of us.
  • Reset

    This way of entering BIOS is quite cardinal. It can be recommended only for experienced users, as it implies opening the laptop case, and in some cases its complete disassembly.

    The method is as follows. In order to reset the BIOS settings, you need to disconnect for a while a special CMOS battery connected to the laptop motherboard. After resetting the settings, the system will “understand” that the parameters may be set incorrectly and will offer to enter the BIOS for configuration, or will open the settings screen automatically.

    A laptop CMOS battery usually looks something like this:

    But there may be options:

    enter, bios, lenovo, laptop

    In addition to the various types of batteries used, it is also worth noting the lack of standardization in terms of the location of the battery on the motherboard. Quite often, you can access the battery just by opening the cover of the hard drive bay:

    But there are also common cases in which to access the battery you will have to disassemble the laptop almost completely and even remove the motherboard:

    In general, the methodology of the method is as follows:

    • Disconnect the laptop from the power supply, remove the battery.
    • We get access to the battery and disconnect it from the laptop motherboard.
    • We are waiting for 10-15 minutes.
    • We connect the battery in place, assemble the laptop, connect the power and start the device.
    • If successful, a screen will appear prompting you to enter the BIOS, or the settings window will automatically open.

    How to enter BIOS on a Lenovo laptop

    Good day!

    Recently, there have been a lot of questions with the BIOS regarding the brand of Lenovo laptops. The fact is that on laptops of this brand (on some models) there is a rather non-standard input into the BIOS (because of this, sometimes even those users who have this is not the first laptop fall into a stupor).

    In general, you may need to change BIOS settings for a variety of reasons. For example, if you need to install Windows, to get information about the disk, the serial number of the laptop, turn on / off a device (say, a sound card or function buttons).

    In this article, I will consider several possible options for entering the BIOS on laptops of this brand. I think the article will be useful to all users who have encountered this problem.

    BIOS Login Methods [Lenovo]

    1) Standard “hot” keys for login

    On the vast majority of laptops of this brand. the F2 or F1 button should act (you need to press immediately after turning on the laptop. Model range: ThinkPad, IdeaPad, 3000 Series, ThinkCentre, ThinkStation).

    On some models. may require pressing the FnF2 key combination (for example, in the G50).

    Addition. The F12 key (FnF12, entering the Boot Menu) is very rare. to enter the BIOS (model Lenovo b590). I also recommend trying.

    If in this way it was not possible to enter. read the following guidelines.

    1) This article will tell you more about the classic entry into the BIOS.

    2) Dedicated recovery button “with an arrow”

    Some Lenovo notebook models have special buttons on the device to enter the BIOS. For example, we are talking about these: g505, v580c, b50, b560, g50, g500, g505s, g570, g570e, g580, g700, z500, z580, Z50, B70 and others.

    How to open BIOS in a Lenovo Laptop

    When turned on, they may not react at all to your pressing the F2 buttons. To enter the BIOS, in this case, you need to use the special Recovery button (with an arrow). You need to press it instead of the power button (i.e. when the laptop is turned off).

    The Recovery button is located on the body of the device, next to the power button (on some models this button is on the side).

    Lenovo G700. button to enter device settings (including BIOS)

    Lenovo B70. a button to enter the BIOS next to the power input. It is most convenient to press with a pencil or pen

    After you click on this button “with an arrow”. the laptop will turn on and you will see a small service menu (usually consists of several items):

    • Normal startup
    • BIOS Setup (BIOS settings);
    • Boot Menu (boot menu, for example, to boot from a USB flash drive without changing the boot queue), etc.

    After your choice of BIOS Setup, you will go to the most common BIOS settings (as in other laptops) and you can set the necessary parameters.

    If you have a blue ThinkVantage button on the device. then press it right after turning on the laptop. while the welcome is still on and the brand of the device manufacturer is displayed (see photo below).

    Next, you will see a menu of several items, among which there will be an entry into the BIOS. F1 button (see arrow-1 on the screenshot below).

    Lenovo model SL510. Logging in with ThinkVoltage

    4) Hole instead of recovery and ThinkVantage buttons.

    A number of Lenovo laptop models do not have any buttons at all, but there is a small hole on the side of the device (usually where power is connected).

    For example, a Lenovo 100 laptop does not have a recovery button (which is with an arrow) at all. There is a small hole (there is an arrow next to the hole). The button itself is located in this hole, to press it. you need to use, for example, a paper clip or a knitting needle.

    Lenovo 100. BIOS entry hole

    Manufacturers, apparently, are trying to exclude accidental button presses. all the same, the vast majority of users have to enter the BIOS very rarely.

    1) Some laptop models do not allow entering BIOS if it is running on battery. I can’t say that this is a 100% glitch, but the setting is very controversial. To check for sure. connect the device to the network and try to enter the BIOS using the methods described above.

    2) The Lenovo v580c model sometimes has a very unpleasant glitch: if you cleaned the disk and installed a new Windows, the BIOS entry buttons will stop working for you.

    To re-enter the BIOS (instructions for advanced users!). turn off the laptop, then unplug it, remove the battery. Next, remove the cover and take out the small battery from the mat. boards. After 5-10 minutes. assemble the device.

    When enabled, the BIOS will be loaded automatically to set the basic parameters. You need to open the “Startup” tab: in the item with the “UEFI / Legacy boot” setting, there are three parameters (Both, UEFI Only, Legacy Only). you need to select “Both”. In the item “UEFI / Legacy Boot Priority”, you need to set “Legacy”. Next, save the settings and restart the laptop. Everything should work as expected.

    READ  How to increase screen brightness on Lenovo laptop

    Removing the battery

    If the owner of a Lenovo laptop is also an extreme lover, he can enter the BIOS by partially disassembling the device case and removing the round battery from the motherboard for a few seconds. and then reinstalling it.

    enter, bios, lenovo, laptop

    As a result, a minor system failure will occur, and with a high degree of probability, upon the next startup, the laptop will automatically boot into BIOS mode, without even asking for permission from the owner.

    How to enter BIOS on Lenovo IdeaPad laptops

    enter, bios, lenovo, laptop

    Recently, I increasingly have to deal with Lenovo laptops. They enjoy well-deserved popularity due to their decent workmanship, while remaining one of the most humane in terms of price. They also have quite non-standard engineering solutions, for example, a way to enter the BIOS, recovery mode or change the Boot Menu parameters.

    Today’s post could be titled like this: “IF ANYTHING DOES NOT HELP. READ THE INSTRUCTIONS”, or rather, I’ll tell you about the “NOVO” button and how to get into the BIOS using the example of the Lenovo IdeaPad 110 laptop.

    When this laptop came into my hands (I had to remove the password on Windows 10) to select an alternative bootloader from the flash drive, I had to get into the BIOS or Boot Menu, but the laptop ignored the standard key combinations (Fn) F2 or (Fn) F1, but on the side of the laptop case there was a special hole with the image of a curved arrow.

    NOVO button

    Owners of Lenovo ThinkPad notebooks, as well as some other models, can enter the BIOS without using key combinations. just use the special NOVO button located next to the power button or on the end of the device.

    After turning off the Lenovo laptop, you should press NOVO and hold it for a few seconds; by selecting the BIOS Setup item in the window that appears, the user can finally enter the BIOS. and continue working in the basic input-output system.

    Tip: sometimes, instead of the NOVO button, there is a special hole on the body of the device, near which the same icon is located. In this case, you can open the BIOS menu by inserting a special paper clip for an iPhone or smartphone or a regular paper clip into the connector and lightly pressing on the contact for two to three seconds.

    How to enter BIOS on a Lenovo laptop

    enter, bios, lenovo, laptop

    • How to enter BIOS on a Lenovo laptop
    • How to open BIOS on a laptop
    • How to enter the BIOS of a laptop
    • – Lenovo laptop user manual.

    Press F2 to enter the main BIOS menu. Here, an experienced user has access to the settings of a large number of parameters of various devices. Unlike conventional PCs, the laptop BIOS also allows you to:

    • how to enter BIOS on a lenovo laptop
    • How to boot the BIOS on a laptop
    • How to enter the BIOS of a computer
    • How to enter BIOS compaq
    • How to start a laptop from a disk via BIOS
    • How to enter BIOS on a Compaq laptop
    • How to enter BIOS in IBM
    • How to get into BIOS on a laptop
    • How to call BIOS on a laptop
    • How to call BIOS on a laptop
    • How to enter BIOS on a computer
    • How to enable hard drive in BIOS
    • How to enable the floppy drive in BIOS
    • How to find the BIOS password
    • How to enter BIOS settings
    • How to enter BIOS settings
    • How to start Windows through BIOS
    • How to open BIOS on a computer
    • How to disable the keyboard in the BIOS in a laptop
    • How to boot the BIOS in a laptop
    • How to enter BIOS on Windows 7
    • How to update the BIOS on a laptop
    • How to view the temperature in BIOS
    • How to change the BIOS on a laptop

    How to enter BIOS

    Notebook BIOS entry methods may differ on different Lenovo models. First, try the standard login method. when you start a personal computer, you need to press the F2 button on the keyboard, sometimes holding down the Fn key before that. Next, the PC parameters menu will be called.

    enter, bios, lenovo, laptop

    But this method is not always working. For some Lenovo models, the BIOS does not load when you press F2 or FnF2. for example, Lenovo Legion Y520, Lenovo G70, G50-30, or G500. If you tried to enter the BIOS using the above method, and you did not succeed, the following instruction is for you:

    • On the side of the laptop (where the charging socket is usually located) or right next to the power button, there should be a special small key with a curved arrow. It’s called Novo Button, One Key Recovery, or One Key Rescue System. You need to turn off the laptop and click on it.
    • If you pressed the correct button, the laptop will start, and on the screen you will see that we are going to a special startup menu:
    • Normal Startup
    • BIOS Setup (parameters);
    • System Recovery
    • Boot Menu.
    • As you probably already guessed, in order to enter the BIOS on Lenovo, you need to go to the BiosSetup item. After you select it, you will see that the laptop entered the BIOS and you can configure it as you like.

    Firmware parameters

    To enter BIOS on Lenovo laptops running “Eights” or “Tens”, you can use the built-in Windows option:

    • Open the “Start” menu and click on the gear image in the leftmost column.
    • In the “Windows Settings” window that opens, enter the “Update and Security” section.

    enter, bios, lenovo, laptop

    • Switch to the “Recovery” tab.

    enter, bios, lenovo, laptop

    • In the section “Special boot options” click on the “Restart now” button. It is important to remember: the process will begin immediately and without additional prompts, and therefore, before clicking, you must close open documents, save the changes made to the system and take other precautions.

    enter, bios, lenovo, laptop

    • In the “Select action” menu, click on the “Troubleshooting” button.

    enter, bios, lenovo, laptop

    • Next. go sequentially to the subsections “Additional parameters”.

    enter, bios, lenovo, laptop

    enter, bios, lenovo, laptop

    • That’s all. it remains to click on the “Restart” button and wait until the BIOS menu appears on the Lenovo laptop screen.

    Important: although, in theory, the specified algorithm should run exactly UEFI, on Lenovo laptops, it is BIOS that is set by default for the initial boot. In addition, even if the owner is in the “extended interface”, he will be able to perform all his tasks in it, bypassing the basic I / O system.

    Enter BIOS on Lenovo

    The newest Lenovo laptops have a dedicated button that allows you to launch the BIOS on reboot. It is located near the power button and is marked with an icon with an arrow. The exception is the Ideapad 100 or 110 laptop and similar state employees from this line, since they have this button on the left side. As a rule, if there is one on the case, then it should be used to enter the BIOS. After you click on it, a special menu will appear where you need to select “BIOS Setup”.

    If for some reason this button is not on the laptop case, then use these keys and their combinations for models of different lines and series:

    However, some laptops have different login keys than those listed above. In this case, you will have to use all keys. from F2 to F12 or Delete. Sometimes they can be combined with Shift or Fn. Which key / combination you need to use depends on many parameters. laptop model, serial modification, equipment, etc.

    The required key can be found in the documentation for the laptop or on the official Lenovo website by typing in your model in the search and finding basic technical information for it.

    It is worth remembering that the most common BIOS keys on almost all devices are F2, F8, Delete, and the rarest ones are F4, F5, F10, F11, F12, Esc. During the reboot, you can try pressing several keys (not simultaneously!). It also happens that when loading on the screen, the inscription with the following m “Please use (required key) to enter setup” is briefly displayed, use this key to enter.

    Entering the BIOS on Lenovo laptops is quite simple, even if you did not succeed on the first try, then most likely you will do it on the second. All “wrong” keys are ignored by the laptop, so you do not risk your mistake to disrupt something in its work.

    We are glad that we were able to help you solve the problem.

    Bookmark the site Lumpics.ru and we will still be useful to you. Thank the author, share the article on social networks.

    Describe what did not work for you. Our experts will try to answer as quickly as possible.

    BYRGPUB.COM 2021