Common ways to sign in on a Lenovo laptop

The most common and well-known way to enter the BIOS is to press the Delete key on the keyboard. However, some computer and laptop manufacturers, including Lenovo, have defined other login methods for their systems.

When choosing a Lenovo manufacturer when purchasing, you need to remember that the computer equipment of this company is produced, as a rule, with an already installed operating system. If you want to reinstall the software on your laptop, you may face a problem: almost all modern models ignore the operating system you want, trying to return the computer to the original one. For this, you will need the ability to enter the BIOS yourself to get around this problem.

Depending on the Lenovo model, you can enter the BIOS in several ways:

• press and hold the F1 or F2 keys;
• press the DELETE button;
• press the Novo Button.

Almost all modern Lenovo laptops have a Novo Button on their panel or side edge. Finding it is not difficult. The manufacturer highlighted it with the appropriate pattern. a curved arrow.

If you need to get into the BIOS on a Lenovo laptop, then instead of the power button, you need to press the Novo Button. At boot, the system will enter BIOS.

Please note that the BIOS will not appear on the monitor immediately. To enter the program, you need to perform one more step. find in the “Novo Button” menu the option to boot the laptop “BIOS Setup”, which is selected with the mouse button. After selecting, press the Enter key on the keyboard. You are logged into the software.

How to enter BIOS: method 5

The latter method is the most radical, and can only be recommended to those users who already have good experience in disassembling such a device. Otherwise, you run the risk of irreparably damaging your Lenovo laptop.

The essence of the method is as follows: to reset all BIOS settings, you need to disconnect for a while a special CMOS battery that is connected to the motherboard of the device. After performing this action, the device will “think” that the settings may be incorrect and will prompt you to open the BIOS to correct them, or it will enter it on its own.

BIOS batteries look different and in almost every model each has its own place, so you have to dig around before you get to it and unplug it. But in general, the procedure is as follows:

• Disconnect the laptop, remove the battery;
• Access the CMOS battery and carefully disconnect it from the motherboard;
• Wait 15-20 minutes (this is necessary so that the CMOS chip is de-energized and the capacitors on the motherboard are discharged);
• Connect the battery back, assemble the laptop, plug in the power and turn on the device;
• If you did everything correctly, you will see the BIOS settings screen.

We hope that one of the above methods helped you find the answer to the question of how to enter BIOS on a Lenovo P70, G50-80, Lenovo ThinkPad T400 or T440 laptop.

How to enter BIOS in Lenovo laptops

The BIOS is a very important computer program written on the chip on the motherboard. It allows the user to change the settings of the software and system software, making them low-level, provides assistance in repairs, and acts as a regulator in the operation of the motherboard. The first thing the wizard does when a computer or laptop breaks down is to enter the BIOS. In 80% of a hundred, it is from there that he receives information about the causes of a system malfunction.

Why might there be a need to enter BIOS on Lenovo at all? Even despite the fact that laptop manufacturers in each new released model try to minimize the requirements for PC knowledge from the user and give the simplest answer to the question of how to set it up or determine the cause of problems, sometimes it becomes necessary to fine-tune the parameters. What you can use this input for:

• Turning on and off some of the hardware parts of the laptop, diagnosing problems;
• Configuring boot parameters for the OS and the entire device;
• Setting up the disk subsystem, in particular, the modes of its operation;
• Customization of many other functions, parts or system in general.

How to enter BIOS on a Lenovo laptop

Good day!

Recently, there are a lot of questions with the BIOS regarding the brand of Lenovo laptops. The fact is that on laptops of this brand (on some models) there is a rather non-standard input into the BIOS (because of this, sometimes even those users who have this is not the first laptop fall into a stupor).

In general, you may need to change the BIOS settings for a variety of reasons. For example, if you need to install Windows, to get information about the hard drive, the serial number of the laptop, turn on / off a device (say, a sound card or function buttons).

In this article, I will consider several possible options for entering the BIOS on laptops of this brand. I think the article will be useful to all users who have encountered this problem.

BIOS Login Methods [Lenovo]

1) Standard “hot” keys for login

On the vast majority of laptops of this brand. the F2 or F1 button should act (you need to press immediately after turning on the laptop. Model range: ThinkPad, IdeaPad, 3000 Series, ThinkCentre, ThinkStation).

On some models. may require pressing the FnF2 button combination (for example, in the G50).

Addition. The F12 key (FnF12. enter the Boot Menu) is very rare. to enter the BIOS (Lenovo model b590). I also recommend trying.

If you can’t enter this way, read the following recommendations.

Note. This article will tell you more about the classic BIOS entry: https://ocomp.info/kak-voyti-v-BIOS.html#BIOS

2) Dedicated recovery button “with an arrow”

Some Lenovo notebook models have special buttons on the device to enter the BIOS. For example, we are talking about these: g505, v580c, b50, b560, g50, g500, g505s, g570, g570e, g580, g700, z500, z580, Z50, B70 and others.

When turned on, they may not react at all to your pressing of the F2 buttons. To enter the BIOS, in this case, you need to use the special Recovery button (with an arrow). You need to press it instead of the power button (i.e. when the laptop is turned off).

The Recovery button is located on the body of the device, next to the power button (on some models this button is on the side).

Lenovo G700. button to enter device settings (including BIOS)

Lenovo B70. BIOS entry button next to the power input. It is most convenient to press with a pencil or pen

After you click on this button “with an arrow”. the laptop will turn on and you will see a small service menu (usually consists of several items): Normal startup (normal boot), BIOS Setup (BIOS settings), Boot Menu (boot menu, for example, to boot from a USB flash drive without changing the download queue), etc.

After your choice of BIOS Setup, you will go to the most common BIOS settings (as in other laptops) and you can set the necessary parameters.

If you have a blue ThinkVantage button on the device. then you need to press it right after turning on the laptop. while the greeting is still on and the brand of the device manufacturer is displayed (see photo below).

Next, you will see a menu of several items, among which there will be an entry into the BIOS. the F1 button (see arrow-1 in the screenshot below).

Lenovo Model SL510. Logging in with ThinkVoltage

4) Hole instead of recovery and ThinkVantage buttons.

A number of Lenovo laptop models do not have any buttons at all, but there is a small hole on the side of the device (usually where power is connected).

For example, a Lenovo 100 laptop does not have a recovery button (which is with an arrow) at all. There is a small hole (there is an arrow next to the hole). The button itself is located in this hole, to press it. you need to use, for example, a paper clip or a knitting needle.

Lenovo 100. BIOS entry hole

Manufacturers, apparently, are trying to eliminate accidental button presses. all the same, the vast majority of users have to enter BIOS very rarely.

1) Some laptop models do not allow entering the BIOS if it is running on battery power. I can’t say that this is a 100% glitch. but the setting is very controversial. To check for sure. connect the device to the network and try to enter the BIOS using the methods described above.

2) The Lenovo v580c model sometimes has a very unpleasant glitch: if you cleaned the disk and installed a new Windows, the BIOS entry buttons will stop working for you.

To enter the BIOS again (instructions for advanced users!). turn off the laptop, then unplug it, remove the battery. Next, remove the cover and take out the small battery from the mat. boards. After 5-10 minutes. assemble the device.

When enabled, the BIOS will be loaded automatically to set the basic parameters. You need to open the “Startup” tab: in the item with the “UEFI / Legacy boot” setting there are three parameters (Both, UEFI Only, Legacy Only). you need to select “Both”. In the item “UEFI / Legacy Boot Priority”, you need to set “Legacy”. Next, save the settings and restart the laptop. Everything should work as expected.

Entering BIOS on Lenovo Laptop: Method 2

Entering the BIOS on a Lenovo laptop is carried out in several ways. unfortunately, there is no single solution for how to get into the BIOS for everyone, but the ways to start it are quite simple. So, let’s move on to the first method.

The most popular solution is to use the keyboard. pressing several buttons at the same time on the laptop immediately after starting it up. Turn off your laptop (this method will not work with enabled), then press the power button and immediately one of the options:

• F2 button or Del button;
• Combination FnF2;
• F1 key

If the BIOS was launched incorrectly, the computer will boot the OS normally. In this case, you will have to turn it off again and call the BIOS again, but using the new boot method. In order not to play the “guessing game” and start the BIOS faster, you can also look at the instructions for the Lenovo laptop.

It also happens that the laptop starts up too quickly, and the user does not have time to press the required combination. To avoid this, turn off the laptop by holding down the power key for 10-15 seconds. Then hold down the desired combination to enter the BIOS, and then press the power button and release, while continuing to hold down the keys to enter the BIOS until the desired screen with parameters appears in front of you.

How to enter BIOS on Lenovo computers?

Lenovo is one of the largest computer companies in the world. And since the demand for the products of this company is growing, the questions about the correct operation and operation of Lenovo equipment are becoming more and more relevant for users. And for those who decided to reinstall Windows, at the very beginning of the process, the question is raised: how to enter Lenovo BIOS?

First, you need to figure out what BIOS is and what it is eaten with. So, BIOS on Lenovo is a special microscopic program that ensures correct and stable interaction between all components of the PC and OS and allows you to customize it. And the BIOS setting is a standard PC setting that helps the system calculate the functions that should be activated and how they should be loaded. BIOS is on any computer, be it Lenovo B560, Lenovo S21 or M5400.

To date, several different versions of Bios have been created, which differ slightly in appearance, but as for the functions, everything is identical here. Each of the versions is used for the initial setup of the computer and for testing it. The BIOS functionality includes:

• Date and time setting;
• Selecting the boot sector. the device from which the operating system will be installed or loaded;
• Checking system components, including checking the health of RAM and hard drives;
• Connection protection. password on your laptop to protect personal data.

How to enter BIOS

Notebook BIOS entry methods may differ on different Lenovo models. First, try the standard login method. when you start a personal computer, you need to press the F2 button on the keyboard, sometimes holding down the Fn key before that. Next, the PC parameters menu will be called.

But this method is not always working. For some Lenovo models, the BIOS does not load when you press F2 or FnF2. for example, Lenovo Legion Y520, Lenovo G70, G50-30, or G500. If you tried to enter the BIOS using the above method, and you did not succeed, the following instruction is for you:

• On the side of the laptop (where the charging socket is usually located) or right next to the power button, there should be a special small key with a curved arrow. It’s called Novo Button, One Key Recovery, or One Key Rescue System. You need to turn off the laptop and click on it.
• If you pressed the correct button, the laptop will start, and on the screen you will see that we are going to a special startup menu:

• Normal Startup
• BIOS Setup (parameters);
• System Recovery (system recovery);
• Boot Menu.

• As you probably already guessed, in order to enter BIOS on Lenovo, you need to go to BIOSSetup. After you select it, you will see that the laptop entered the BIOS and you can configure it as you like.

Two secrets of running BIOS

But if you still did not manage to start the BIOS using one of the above methods, and the laptop is running Windows 8.1 or higher, we will tell you two startup secrets.

• You need to turn on the PC. In a running computer on the desktop, drag the mouse pointer to the lower right corner of the desktop (call the side menu).
• A menu opens to us, where we select the items “Options”. “Update and Recovery”. “Recovery”.
• Here, in the “Special boot options” section, click on the “Reload now” button.
• Next, a blue screen with tiles will open. Open the “Diagnostics” tile, by clicking on which you will be taken to additional parameters.
• You need to open the item “UEFI Firmware Options” and click the “Restart” button. Done! You are in BIOS!

Second secret. Many Win 8.1 users make an error when trying to enter BIOS. Everyone knows how to get into the BIOS. you need to press a certain button on the keyboard. To do this, the user clicks on “Shutdown”, waits for the laptop to turn off, and then presses the button to enter the BIOS, but the computer starts up as before. the OS is loading.

The whole problem is that the Windows 8.1 operating system works initially with the fast startup function, which is based on sleep mode. enter the BIOS without turning off the PC, but restarting it.

Some helpful tips:

• After entering the BIOS, go to the various settings of the system parameters and its boot in the BIOS itself. Be very careful and careful, and it is better not to touch what you do not know, as there is a risk of doing something wrong and completely losing your computer. After making all the changes, go to the “Exit” section and select “Save exit”. After that, the laptop will be restarted, and on a new start, all the settings that you had to set before will already be taken into account.
• If the above methods of entering BIOS on a Lenovo laptop do not work, try holding down the F12 key while starting the device until the BIOS starts. this method works on some Lenovo models.
• It is very rare, but it still happens. in some models the F1 key works (you need to press it several times while the laptop turns on).
• Manufacturers recommend adjusting PC settings in BIOS only with a fully charged laptop battery, since if during the setup process your laptop turns off due to being discharged, then this is likely to cause some system problems in the future.
• Before exiting BIOS, be sure to save all changes so as not to get lost.

Remember that BIOS setup is a very serious undertaking that requires maximum understanding of the process and great attention to detail. You should be aware that if the configuration is incorrect, some components of the system may not work correctly, which brings additional difficulties in operation. And if you doubt that you know how to do it right, it is better to call qualified specialists, this will save money, time, and nerves. We hope this article helped you figure out how to enter BIOS.

How to enter BIOS on a Lenovo laptop

Good day!

Recently, there are a lot of questions with the BIOS regarding the brand of Lenovo laptops. The fact is that on laptops of this brand (on some models) there is a rather non-standard input into the BIOS (because of this, sometimes even those users who have this is not the first laptop fall into a stupor).

In general, you may need to change the BIOS settings for a variety of reasons. For example, if you need to install Windows, to get information about the hard drive, the serial number of the laptop, turn on / off a device (say, a sound card or function buttons).

In this article, I will consider several possible options for entering the BIOS on laptops of this brand. I think the article will be useful to all users who have encountered this problem.

BIOS Login Methods [Lenovo]

1) Standard hotkeys for login

On the vast majority of laptops of this brand. the F2 or F1 button should act (press immediately after turning on the laptop. Model range: ThinkPad, IdeaPad, 3000 Series, ThinkCentre, ThinkStation).

In some models. may require pressing a combination of FnF2 buttons (for example, in the G50).

Addition. The F12 key is very rare (FnF12. Enter the Boot Menu). to enter BIOS (Lenovo model b590). I also recommend trying.

If in this way it was not possible to enter. read the following guidelines.

Note. This article will tell you more about the classic BIOS entry: https://ocomp.info/kak-voyti-v-BIOS.html#BIOS

2) Dedicated recovery button “with an arrow”

Some Lenovo notebook models have special buttons on the device to enter the BIOS. For example, we are talking about these: g505, v580c, b50, b560, g50, g500, g505s, g570, g570e, g580, g700, z500, z580, Z50, B70 and others.

They are when turned on. may not respond at all to your F2 button presses. To enter the BIOS, in this case, you need to use the special Recovery button (with an arrow). You need to press it instead of the power button (i.e. when the laptop is turned off).

The Recovery button is located on the body of the device, next to the power button (on some models this button is on the side).

Lenovo G700. button to enter device settings (including BIOS)

Lenovo B70. a button to enter the BIOS next to the power input. It is most convenient to press with a pencil or pen

After you click on this “arrow” button. the laptop will turn on and you will see a small service menu (usually consists of several items): Normal startup (normal boot), BIOS Setup (BIOS settings), Boot Menu (boot menu, for example, to boot from a USB flash drive without changing the boot queue), etc.

After your choice of BIOS Setup. you will go to the most common BIOS settings (like in other laptops) and you can set the necessary parameters.

If you have a blue ThinkVantage button on your device. then it must be pressed immediately after turning on the laptop. while the greeting is still on and the brand of the device manufacturer is shown (see photo below).

Next, you will see a menu of several items, among which there will be an entry into the BIOS. F1 button (see arrow-1 on the screenshot below).

Lenovo model SL510. Logging in with ThinkVoltage

4) Hole instead of recovery and ThinkVantage buttons.

A number of Lenovo laptop models do not have any buttons at all, but there is a small hole on the side of the device (usually where power is connected).

For example, a Lenovo 100 laptop does not have a recovery button (which is with an arrow) at all. There is a small hole (there is an arrow next to the hole). The button itself is located in this hole in order to press it. you need to use, for example, a paper clip or a knitting needle.

Lenovo 100.Bios Entry Hole

Manufacturers, apparently, try to exclude accidental button presses. all the same, the vast majority of users have to enter the BIOS very rarely.

1) Some laptop models do not allow entering the BIOS if it is running on battery power. I can’t say that this is a 100% glitch. but the setting is very controversial. To check for sure. connect the device to the network and try to enter the BIOS using the methods described above.

2) The Lenovo v580c model sometimes has a very unpleasant glitch: if you cleaned the disk and installed a new Windows. BIOS entry buttons will stop working for you.

To enter BIOS again (manual for advanced users!). turn off the laptop, then unplug it, remove the battery. Next, remove the cover and take out the small battery from the mat. boards. In 5-10 minutes. assemble the device.

When enabled, the BIOS will be loaded automatically to set the basic parameters. You need to open the “Startup” tab: in the item with the “UEFI / Legacy boot” setting, there are three parameters (Both, UEFI Only, Legacy Only). you need to select “Both”. In the item “UEFI / Legacy Boot Priority”, you need to set “Legacy”. Next, save the settings and restart the laptop. Everything should work as expected.

Entering UEFI Settings from Windows 10

To use this method, Windows 10 must be installed in UEFI mode (as a rule, it is), and you must be able to either log into the OS itself, or at least get to the login screen with a password.

In the first case, you just need to click on the notification icon and select “All parameters”. Then in the settings open “Update and Security” and go to the item “Recovery”.

lenovo ideapad 100 Bios Setup / Boot Menu Key

In the recovery, click the Restart Now button under the “Special Boot Options” section. After the computer restarts, you will see a screen that is the same (or similar) to the one shown below.

Select the “Diagnostics” item, then. “Advanced options”, in the additional options. “UEFI firmware settings” and, finally, confirm your intention by clicking the “Restart” button.

After a reboot, you will be taken to the BIOS or, more precisely, UEFI (just out of habit, the settings of the motherboard are usually called BIOS, probably this will continue in the future).

How To Get into Bios Lenovo Ideapad 100

In the event that you cannot log into Windows 10 for some reason, but you can get to the login screen, you can also go to the UEFI settings. To do this, on the login screen, press the “power” button, and then, while holding down the Shift key, press the “Restart” item and you will be taken to the special boot options for the system. Further steps have already been described above.

How to enter BIOS (UEFI) in Windows 10

One of the most common questions regarding the latest OS versions from Microsoft, including Windows 10, is how to enter the BIOS. At the same time, more often it is still in the form of UEFI (often characterized by the presence of a graphical settings interface), a new version of the motherboard software, which replaced the standard BIOS, and is designed for the same. setting up the operation of equipment, boot options and obtaining information about the system state.

Due to the fact that Windows 10 (as well as 8) implements fast boot mode (which is a hibernation option), when you turn on your computer or laptop, you may not see a prompt like Press Del (F2) to enter Setup, which allows you to enter the BIOS by pressing Del (for PC) or F2 (for most laptops). Nevertheless, getting into the desired settings is easy.

Entering BIOS when turning on the computer

There is also a traditional, well-known method to enter the BIOS (also suitable for UEFI). press the Delete key (for most PCs) or F2 (for most laptops) immediately when the computer is turned on, even before the OS starts to boot. As a rule, on the boot screen below the inscription is displayed: Press Key_Name to enter setup. If there is no such inscription, you can familiarize yourself with the documentation for the motherboard or laptop, such information should be present there.

For Windows 10, entering the BIOS in this way is complicated by the fact that the computer boots up really quickly, and it is not always possible to press this key (or even see a message about which one).

To solve this problem, you can: disable the fastboot function. To do this, in Windows 10, right-click on the “Start” button, select “Control Panel” from the menu, and in the control panel. Power.

On the left, click on “Power button actions”, and on the next screen. “Change settings that are currently unavailable”.

At the bottom, in the “Shutdown Options” section, uncheck “Enable Fast Startup” and save the changes. After that, turn off or restart your computer and try to enter the BIOS using the required key.

Note: In some cases, when the monitor is connected to a discrete graphics card, you may not see the BIOS screen, as well as information about the keys to enter it. In this case, reconnecting it to the integrated graphics adapter can help (HDMI, DVI, VGA outputs on the motherboard itself).

Distribution of new, sometimes interesting and useful materials from the remontka.pro website. No ads and free computer help for subscribers from the author. Other subscription methods (VK, Odnoklassniki, Telegram., YouTube, Yandex.Dzen)

Good afternoon, the problem is this: Aspire v-5 571G laptop 2012 onwards. Installed Win 10×64 (native was Win. 7×64), after an unsuccessful attempt to install again, but as the 2nd OS Win. 7×64, it became impossible to get into UEFI, rummaged through the Internet, none of the methods helped. I took out the battery, bridged the contacts, the BESTOLKU! When you start F2 (standard input to UEFI), Del, F8 and all other keys do not respond (the keyboard is new), the standard OS boot occurs. Through “Restore \ Reboot” “Additional parameters”, the item “UEFI firmware parameters” is absent, but the software is UEFI! I did not update anything myself. In the system information: “BIOS version P.T.Ltd. v1.10, BIOS Mode Obsolete. ” Windows is loading, it works fine, but it is not possible to set the type of loading. Maybe you faced such a problem, tell me?

Hello.
No, there are no ideas, and I didn’t notice this at all on Acer (Lenovo has a similar problem, but I don’t remember the solution right away, try Google on the topic “Lenovo enter BIOS Windows 10”). You also tried to disable Fast Boot in Windows 10, right? And cut it down with a long press of the power key when the OS is working, and then hammer on F2? If so. then weird.

Hello Dmitry, another question: “How to perform a clean installation of Windows, if it is impossible to enter the BIOS, UEFI.” What if, in some “BARBARIAN” way FORMAT, spoil Windows so that the OS does not boot at all, insert an installation USB flash drive or disk, turn on the PC, whether a clean installation of the OS will start, it is very interesting what you think?

Hello.
Depends on BIOS settings. That is, for example, on some laptops, loading from an external drive is generally disabled by default, then the method will not help.
In this case, it is better to use another version of the same method, less barbaric: disconnect the hard drive, connect the USB flash drive, check if it is booting from it.

Good time, Dmitry, loading from an external drive is in progress, it remains to bring Windows to an INACTIVE state, but how to do it? AVAST Premier has the dreaded “Erase the entire disc and all data on it” option. Can I use it or otherwise, tell me?
(It’s all about the digital license, it flew off, microsoft recommends a clean installation of the OS)

Sergey, no, it is not necessary, spoil the disk in vain (i.e. wear it out. this function for wiping the disk space with zeros without the possibility of recovery is not needed in your case). Just boot from the installation flash drive, select “custom installation” and there you will have the opportunity to format the partition on which Windows is currently installed (it will automatically become inoperative).
You say it is impossible to enter the BIOS, but: in the absence of both disks (internal and external), entering the BIOS should work, and you, in turn, can install an external drive as the first boot device.

Yes, Dmitry, you are absolutely right! “Special Boot Options”, of course, and I had everything set up clean. The moment the digital license was activated, the HDD was breathing. Without your advice, I probably would have killed the disk. The coolest positive to you! Thank you from the bottom of my heart!

Full reset can be performed. Options. Update & Security. Recovery. Special Boot Options. Restart Now. Reset your computer to its original state. And then follow the instructions.

Good afternoon Dmitry!
With Lenovo. I smashed all the brains into parts, as Vysotsky sang. The nature of the problems was akin to that of Sergei. It turned out that you can enter the BIOS only from a reboot, strenuously tormenting F12. over, only from every third reboot. This behavior has remained a mystery to me.
I would be glad if this set of actions helps someone.!
Thank you for the easy-to-understand, well-organized and more than useful site.!

But what if you can’t enter the BIOS in any way? If there is some other way to reinstall the system without resorting to third-party help and exiting the BIOS?

You can reset the system, in fact it is a reinstallation. https://remontka.pro/reset-Windows-10/

Hello
I have a Lenovo mix 10 tablet
I thought of reinstalling the system from a USB flash drive, but after entering the ufi through the parameters, I could not change the boot disk. The buttons “Information”, “Configuration” and “Exit” pop up. I press “Configuration”, but I can’t get to the “boot” menu. Prompts you to save or not save changes and exit

Hello. And there is no key for just calling the boot menu?. https://remontka.pro/boot-menu/ ?

Lenovo laptop (Windows 8.1). Black screen when entering BIOS via UEFI after reboot.

And other ways to enter the BIOS do not work either.?

When entering through the Novo Button Menu button when pressing BIOS Setup
the same black screen appears.

When voltage is applied to the PC (Dell Vostro 3667), it starts without pressing the power button for 3 seconds. and shutdown. Then I turn it on with the button and the PC works fine. In BIOS, start on power-up in the Power off position. Is adjustment possible or is it a malfunction?

Hello. Windows 10 on board?
What if you turn off Fast Startup (see https://remontka.pro/fast-startup-Windows-10/) and then quit? The problem disappears?
If it disappears, then 90% of the problem is in non-original or missing power management drivers. Place them using Dell Support Assist (or manually from the Dell website for your particular model). Specifically for your laptop, these are Intel AMT HECI ME and Intel Chipset Device Software Driver.

Hello. I have a Lenovo B590 laptop (20208), Windows 10, BIOS. H5ET85WW (1.23). After switching from 8 to 10, it became impossible for me to enter the BIOS, Boot Menu and Safe Mode from the keyboard. When holding or quickly poking cl. Esc; Del; Enter; F1.F12 and when combined with Shift, they simply do not respond to pressing, when you press NOVO, the OS starts in normal mode. I was interested in various forums, but did not receive an intelligible answer. Question. Could this be due to incorrect BIOS settings? I absolutely did not change anything there. Now I can only enter the BIOS through the interface or by pressing CtrlAltDel and then Shift reboot. All this provided a working OS.

Hello.
Try this option:
1.Disable Windows 10 Fast Startup. https://remontka.pro/fast-startup-Windows-10/
2.try to call the boot menu / BIOS in the same way as they did on the 8-ke.

I tried all the methods that I found on the Internet (and they are all the same) and none of them helps. Well, firstly, I do not have the item “UEFI firmware settings”, and secondly, even if you disable fast boot, the boot is fast anyway and you cannot enter the BIOS with any combinations. And the motherboard is not simple. ASUS LGA2011 Sabertooth X79.

Is the keyboard accidentally connected to USB 3? Connect to 2.0, disable Windows Fast Startup (if enabled again) and Del should come in. And if suddenly a PS / 2 keyboard is lying around somewhere, then it should definitely work with it, and the connector, I see, you have.

It was a dozen pro., Stood for about a year. Everything seemed to be fine. Recently, after updates, the mouse does not work, then the sound disappeared and the keyboard. Tried reinstalling the drivers, useless. Demolished 10k, put 7k and everything works.

Thanks, it was not possible to enter the BIOS, the “special boot option” helped.

And when you click in UEFI Firmware Options, then everything is deleted from the computer or not ?

Hello. When I rebooted Windows (as shown above), I did not have a button to open the BIOS (instead of it there was “Delete updates”) Are there ways to solve this? And what is it connected with?

And additional parameters or something similar was there?

Hello. I have such a question laptop Acer Predator Helios 500, the latest version of 10ki is installed with all updates. Applications from Acer are not installed, the problem is solved by entering the BIOS and entering the initial model data (snippet). But the problem is that the manufacturer has set a password on the BIOS. I have a question whether this method will help me enter the BIOS or not?

Hello. I assume that they will ask for a password in the same way.

Good day! a problem with the UEFI BIOS I can not go to the extended section in order to enable a discrete video card and connect a second monitor to the system unit via VGA

Hello.
And what exactly and how does it fail? ? And the photo can be posted somewhere and a link can be given, perhaps I will see some nuance.

Hello. I can not enter the BIOS ufi. As I did not try, the parameters pop up, but when I press the buttons to enter the BIOS there, there is simply no other button instead of it. I went there but failed. Tell me, please, what can it be

Hello. And some other. what is it? Just can’t log in from the keyboard? And if you first disable fast startup of Windows 10. https://remontka.pro/fast-startup-Windows-10/

After I went into the additional parameters, the UEFI button was not there. What can be done about it?

Is it just that you can’t enter the BIOS by pressing the key? After shutdown with Shift shutdown.

And what if I have Uefi Boot Support in the off position in my BIOS and Windows has been installed for a long time. Can I enable uefi boot support or only Windows will have to be reinstalled? I need to adjust the speed of the cooler, it is not in a regular BIOS, I hope there is uefi, but I don’t know if it can be turned on or not.?

If you turn it on, nothing should change. But the points for the fan speed, if they are not already there, will not appear.

I cannot log into UEFI using regular methods: in recovery mode. Diagnostics. add. options. in this menu I don’t have Firmware options.
Yes, on reboot, I easily enter by pressing delete. but besides, in the same menu I have these 6 items:
Startup recovery
Boot options
Command line
Remove updates
System Restore
System image recovery

The above items are standard items in the Windows 10 recovery environment, if that’s what you mean. But maybe I did not quite understand your question, and if there is ambiguity, you can post a photo somewhere and describe what exactly is not clear there.

Thanks for the great advice, but I don’t even have such an item in the restoration

Win 10, desktop computer). When you try to enter the BIOS at startup (tried ESC, F2, Del), when you start with fastboot disabled (as in the article), when you reboot in the “special boot options” section (as in the article), there is just a black screen. I waited once for half an hour, nothing appeared. It may take longer?

No, it doesn’t seem like it takes longer. But what exactly is the matter is not clear.

How to enter BIOS on a Lenovo laptop

Good day.

Lenovo is one of the most popular laptop manufacturers. By the way, I must tell you (from personal experience), laptops are quite good and reliable. And there is one feature of some models of these laptops. an unusual entry into the BIOS (and you often need to enter it, for example, to reinstall Windows).

In this relatively short article, I would like to consider these features of the entrance

Entering BIOS on a Lenovo laptop (step by step)

1) Usually, to enter the BIOS on Lenovo laptops (on most models), it is enough to press the F2 (or FnF2) button when it is turned on.

However, some models may not react at all to these presses (for example, Lenovo Z50, Lenovo G50, and in general the model range: g505, v580c, b50, b560, b590, g50, g500, g505s, g570, g570e, g580, g700. z500, z580 may not respond to these keys)

2) The above models have a special button on the side panel (usually next to the power cable) (for example, Lenovo G50 model, see Fig. 2).

To enter the BIOS, you need to: turn off the laptop, and then click on this button (an arrow is usually drawn on it, although I admit that on some models the arrow may not be).

By the way, an important point. Not all Lenovo laptop models have this service button on the side. For example, on a Lenovo G480 laptop. this button is next to the laptop power button (see Fig. 2.1).

3) If everything was done correctly, the laptop should turn on and a service menu with four items will appear on the screen (see Fig. 3):

To enter BIOS. select BIOS Setup (BIOS settings and settings).

4) Next, the most common BIOS menu should appear. Then you can configure the BIOS in the same way as other laptop models (the settings are almost identical).

By the way, maybe someone will need it: in fig. 4 shows the settings of the BOOT section of the Lenovo G480 laptop for installing Windows 7 on it:

• Boot Mode: [Legacy Support]
• Boot Priority: [Legacy First]
• USB Boot: [Enabled]
• Boot Device Priority: PLDS DVD RW (this is a drive with a Windows 7 boot disk installed in it, note that it is the first in this list), Internal HDD

After changing all the settings, do not forget to save them. To do this, in the EXIT section, select “Save and exit”. After restarting the laptop, the installation of Windows 7 should start

5) There are certain laptop models, such as Lenovo b590 and v580c, where you may need the F12 key to enter the BIOS. Holding this key right after turning on the laptop. you can get into Quick Boot (quick menu). where you can easily change the boot order of various devices (HDD, CD-Rom, USB).

6) And the F1 key is used quite rarely. You may need it if you are using a Lenovo b590 laptop. The key must be pressed and held after turning on the device. The BIOS menu itself differs little from the standard.

The manufacturer recommends that you charge the laptop battery sufficiently before entering the BIOS. If during the process of setting and setting parameters in the BIOS, the device is abnormally turned off (due to lack of power). there may be problems in the further operation of the laptop.

To be honest, I’m not ready to comment on the last recommendation: I have never experienced problems when turning off a PC when I was in the BIOS settings