How to launch Wi-Fi on Windows 10

We show you the fastest way to turn on Wi-Fi on Windows 10.

  • A window will appear, here click “Wi-Fi”, above drag the slider to the position “On”. Done, after startup your laptop will scan and give you all the Wi-Fi networks that are available. If it does not happen, it is useful to read article: Why WI-FI on PC does not work.

Why the network does not work and disconnects on your laptop with Windows 10 and 7

If Wi-Fi stops working on your Windows 7 or 10 laptop, often after performing a diagnostic, a notification pops up that “Wireless is disabled” and the error itself has a status of “uncorrected”.

How to Enable your Wireless Internet Connection in Windows 10/8/7

What does the message “Wireless connection disabled” mean

This error indicates that the network adapter that your laptop uses for wireless networking is disabled. In such a situation, a red cross appears in the notification panel next to the connection icon, and when you click on the icon, the current status “No connection” will be shown.

If this happens, it means that Windows itself can not fix the problem automatically, and you will have to do it manually.

Causes of the error

On the newer models, it may happen that the wireless network access is suddenly cut off:

  • In order to save power consumption;
  • Due to outdated drivers;
  • Or as a result of using the wrong network adapter settings.

There may be several ways to fix the error and turn on Wi-Fi on different versions of Windows.

Option: To start Wi-Fi, use the device manager

Here is another way to easily enable WI-FI on your laptop. There we will activate it using the Device Manager menu.

  • To begin, go to “Start”, hover your cursor over the “My Computer” shortcut and right-click. From the list that appears, select “Properties”.
  • From the list, find and expand Network Adapters. There you will find a line with the word “Wireless” Click on this line and in the window that appears choose “Enable“.

Done, now you know how you can turn on Wi-Fi on Windows 7 laptop using the task manager.

The connection status is marked with a red cross or there is no connection.

If the panel has a status marked with a red cross, it indicates that the Wi-Fi module is disabled programmatically. Consequently, it is not possible to find the notebook available networks. To activate the module, go to “Control Panel”. “Network Connections” and call the utility “Windows Mobility Center”. You can also right-click on the battery indicator in the bottom right corner. taskbar area.

A window will open where you are free to activate or deactivate not only the Wi-Fi module, but also to select the mode for battery saving or to connect the external display. Just click on the button “Enable wireless network” and Wi-Fi will be activated. Some laptops have a button to perform this function. It is usually located on the end or above the keyboard.

Sometimes the status icon does not appear in the taskbar. As a rule, the informing icon is not displayed for such reasons:

Missing or incorrectly installed drivers. View the status of the wireless network adapter in the “Device Manager. Click on “Start. Right-click on “Computer” and “Properties” drop-down list. A window will open, where you will need to select “Device Manager” on the left.

See also  How to install a web browser on LG TV

Update the drivers, if necessary. However, driver problems are rare, and in my case it works fine.

often than not, you just need to turn on the Wi-Fi module in your laptop. Go to “Start. “Control Panel”. Click on “Network and Sharing Center” and in the left-hand column, look for “Change Adapter Settings”. The wireless network connection is displayed here. Right-click on it and click “Enable“.

Then everything is as described above. That’s all there is to it. I think you are convinced that to connect your laptop to Wi-Fi is not difficult.

Using the internal adapter

Connecting your device to the network this way is quite tricky, as you will have to climb into the system unit (SB) here. To do this:

  • Unplug the computer from the power outlet.
  • Remove the side cover of the SB.
  • Find the PCI port, then unscrew and remove the plug.
  • Install the device in a PCI port.
  • Insert the plug and tighten the screw.
  • Reinstall the SB cover.
  • Connect the antennae to the adapter.
enable, wireless, networking, your, computer

.If the device is successfully connected you should see an icon on your computer screen. Click on it to select the network and enter the password.

Setting up Wi-Fi on a computer with Windows XP

You will also need to start in the system tray on Windows XP. Right click on the wireless network icon. A window will pop up, where you will need to select the last item “View available wireless networks”.

It is also possible to achieve the goal in another way, through Windows Explorer. Open it and go through “My Computer” folder to the control panel. It remains to go to the network connections branch and see the available wireless networks.

There is also the third variant. Use the “Start” menu. Find the “Network Connections” item in the settings.

Having followed any of these options, you need to proceed as follows:

  • A window pops up where you have to select your access point, click on it and “Connect.
  • In the new window, enter the symbols of the security key, then confirm the password and “Connect”. enter the symbols carefully, as in this system version you cannot see them.
  • The box of wireless network connection will pop up. you need to wait until the device is connected to the network.
  • Connection should be established.

If you want to change the Wi-Fi settings in Windows XP, you must do it manually. It is better to use Explorer:

  • In Network Connections go to “Wireless Network Connection 2” by right-clicking and holding.
  • Find “Properties” at the end of the popup window.
  • After all the necessary changes have been made, all that remains is to save them.

Let’s look at the four most popular methods of connecting your computer to a wireless network.

External adapters

This device is similar to a small flash drive. Different manufacturers sell these devices, starting from 400. Connect the device to the system unit.

To set up the external adapter and connect the Wi-Fi, follow the instructions:

  • Connect the device to the PC through the USB input. Next, a window should pop up, reporting a successful activation.
  • Then insert the disc with the drivers into the drive of the computer, the installation begins. After that, you need to press the “Next” button, disregarding the information that pops up.
  • After the drivers will be installed, on the taskbar you will need to find the icon of a wireless network, which appeared there. Click on it, select your network and enter the password.

If there are still questions, see the video guide on how to connect Wi-Fi adapter to the computer:

If your computer is running Windows XP, the wireless network icon will not appear. It is found by yourself. To do this, you need to go to “Network connections”, from the list that appears, select your network and enter the password.

Internal adapters

IT experts do not recommend first-time users to connect Wi-Fi using the internal adapter, as it is rather complicated. But if a novice still decides to do it, he or she needs to open the system unit, t. к. the device is connected to the motherboard.

See also  How to record video from camcorder to computer

The procedure for connecting the internal adapter is as follows:

  • Disconnect PC from power source, remove the side cover of system unit, as well as remove the antennas from the plug-in device itself and find unoccupied PCI connectors.
  • Next, unscrew and remove the blanking plug from the selected free connector.
  • Then the device is installed in a suitable connector. While plugging it in, hold on to the edge for fastening and the right side of the motherboard. To fully place the adapter in the slot, you need to push it slightly.
  • The plug is reinstalled in its original place. The user should also remember to tighten the screw.
  • The last step is to put the lid of the system unit back. Do not forget to attach the antennas from the adapter to the back of the device.

After installing the adapter on the PC, it is necessary to set it up. To do this, the user must install the drivers, wait until the network icon appears, or find it himself, and enter the requested data.

You can visually see how to install the external Wi-Fi adapter in the system unit of your computer, in the following

Using the router

It is also possible to connect the PC to Wi-Fi with the help of a router, in addition to which a wire will be needed. To do it this way:

  • Connect the device to a power source, connect one end of the cable to the lan port of the router and the other end to the PC network card. Then you should see the indicator.
  • Then you need to log in to the router settings and enter the IP address into the address bar. You can read this information on the back of the device. Then you have to enter your login and password. As a rule, it is “admin” in both cases.
  • Then the user needs to find the tab “Network”, select the “WAN” in it and indicate the type of network connection which is used by the connected Internet provider. The information is listed on the official website of the provider or in the contract with the provider.
  • Then you need to find the “Clone MAC”, select “Clone MAC-address”, accept the changes and save them.
  • Then you need to open the “Wireless Networks” tab, click the “Wireless Network Setup” option, give it a name.
  • Perform reboot via the “System Tools” tab.

After the above manipulation the router will start distributing Wi-Fi to other devices. To connect to the wireless Internet in the future, you can simply select your network and enter the requested data in the appeared bar.

How to connect and configure a router (we’ll take a popular TP-LINK router as an example) for Wi-Fi connection on a PC, see the video below:

Replacing the motherboard

Today there are motherboards with a Wi-Fi adapter. Replacing your regular motherboard with this one allows you to connect your computer to the wireless Internet.

Usually there are built-in Wi-Fi adapters only on expensive, high-quality motherboards. So connecting to a wireless network this way can be a very expensive procedure. In addition, the process of replacing the device is quite complicated, so it is better to entrust it to a specialist.

enable, wireless, networking, your, computer

In general, the instructions for replacing the motherboard are as follows:

  • Removing both side panels of the system unit.
  • Next you need to replace the connector panel, which is located at the back of the case. This part should be replaced with a new one, which comes with the purchased board.
  • Then you need to find the racks (the elements that prevent the board to touch the chassis of the system unit). Once the racks are found, you need to install the ones that come with the board.
  • Then the motherboard is installed onto the standoffs.
  • Next, all the components are installed, connected to the power source, connect the front of the system unit. The last step is to close the system unit case.
See also  Setting up a Windows 10 WEB camera on a computer

The switch or a button, usually the manufacturer is placed on one side of the laptop. Next to or on it is sure to have a wireless network icon.

The factory default solutions for turning on the Wi-Fi module are not very diverse, as each manufacturer is trying to simplify and standardize the network connection procedure for their equipment.

For example, “Lenovo” provides several ways to connect to Wi-Fi simultaneously. Their laptops sometimes have a physical toggle switch to activate the Wi-Fi adapter,

as well as a specially provided key.

The most commonly used combination is Fn and F5, but sometimes the key responsible for the inclusion is F3.

often the simultaneous pressing of “Fn” and “F12” is used.

Earlier HP laptops had a separate key above or below the keyboard.

Often the latest HP models are equipped with a touch key where you can adjust and activate the Wi-Fi adapter with a touch of your finger.

On “Asus” you need to hold the “FN” key and click “F2”.

Older laptops from this manufacturer had separate switches located on one end of the mobile PC.

Such a toggle switch should simply be set to the “On” position and the adapter will be activated.

The software

In “Windows” there is an automatic download of drivers, but sometimes the software for some devices is not installed or does not work correctly.

In such cases, you need to install the software yourself. There are only a few steps to do this:

  • Guided by steps 1. 5 of the above instruction to run the “Device Manager”;
  • If the device is not functioning properly, a yellow sign is sure to appear next to it “!”;
  • The adapter will be displayed as an item “Unknown device”;
  • You have to call the context menu from this problematic hardware and click “Uninstall”. Then confirm your intentions and restart the PC after removal;
  • Usually after booting “Windows” finds new hardware, and in case the automatic function does not work, you should reopen the manager and in the “Actions” tab click on “Refresh”.

If the above is not successful, you will need to perform the following steps:

  • Re-enter the “Actions” tab;
  • Click the “Install old device” line;
  • In the window that appears, click “Next”;
  • Specify “Auto search” or “Manual”;
  • Then highlight “Network adapters”;
  • Find the device model in the list;
  • Wait until the installation is complete and restart the PC.

If you need to update drivers, the algorithm will consist of the following steps:

  • Following items 1. 5 from the first instruction, start “Device manager”;
  • Then from the problem hardware call the context menu;
  • Click on “Update Driver”;
  • It is recommended to specify “Auto Search”, and the OS will find and install the software on its own;
  • Or, if the user has previously downloaded the software and saved it to a PC, click “Search on Computer” and show the location of the downloaded drivers.

To manually find and download the appropriate software, you need to perform the following steps:

  • Open the developer’s website;
  • Type the hardware model in the search field and click “Enter”;
  • Enter “Devices” section;
  • Save the drivers for the hardware in your PC’s memory.

If you have difficulty doing the task manually, you can use programs that are specifically designed to install software. One such application is “Driver Booster.

The advantage of using it is mainly in the automatic detection of the device model and loading the latest software modifications.

BYRGPUB.COM 2022