How to charge iPhone without charging at home

Modern gadgets are almost always portable devices that are not permanently connected to the electrical network. The batteries installed in them allow such devices to work autonomously for some time. Sometimes it happens that these elements or chargers fail, and the phone needs to be urgently used. It is at such moments that the thought of how to charge an iPhone without charging comes.

Charge iPhone 4, 5, 6, 7 without charger

If you need to charge your iPhone, but you don’t have a working charger or outlet at hand, then you don’t need to panic. The best solution would be to repair the original charger and use it normally. You can charge your phone without a power supply and even without an outlet using a wind generator and even a battery made of fruits or vegetables, but these are completely exotic methods that involve partial disassembly of the device and can cause irreparable harm to it. It is much safer to use standard methods if the power supply or charger suddenly breaks.

disassemble, iphone, home

If the wired charging is broken, then you can use the wireless

  • USB port of a personal computer or laptop;
  • wireless charging;
  • battery case;
  • some other possible options.

Charging with a USB cable requires the use of an original wire or cord from any other manufacturer that matches the iPhone connector. The cable connects one side to the phone and the other to any working port on a PC or laptop. Charging in this way is carried out more slowly than from a regular outlet. The thing is that the port capacity is usually not enough.

The second method, how to charge your iPhone without charging at home, is to use a dedicated wireless device. It does not fit all phone models. The official website gives the following list of supported gadgets: iPhone 8, iPhone 8 Plus, iPhone X, iPhone XS, iPhone XS Max, iPhone XR, iPhone 11, iPhone 11 Pro and iPhone 11 Pro Max.

The Smart Battery Case also enables successful battery recharge. Before using this method, you need to update your iPhone‘s iOS firmware to the latest version. Simply put, the case is a regular power bank.

Important! There are several other options as well. One of them is based on the use of solar-powered charging. You can also purchase a dynamo charger that will power the phone by rotating its handle and generating an electric current.

What to do if iPhone won’t charge

It also happens that the phone simply refuses to charge, even with the original charging or through a connection to a third-party battery or personal computer. There may be a lot of reasons for this. The main ones are:

  • Breakdown of the socket. You should check the outlet with other electrical appliances or move the phone to another room for charging.
  • Failure of the power supply or cable. Even original and high-quality Apple accessories can be broken and no one is safe from this. It is necessary to try to recharge the gadget in other ways in order to exclude internal damage.
  • Faults in the power connector on the phone. If dust, dirt or water got into it, then this could cause poor contact and the inability to receive electricity.
  • The controller is burnt out or out of order. Power management and charging are controlled by a special chip that could be damaged mechanically or by getting moisture into the device case. In the latter case, corrosive processes could occur that prevent the electric current from passing freely through the board to the battery.

Important! There can be a huge number of reasons for a malfunction. To solve the problem, it is recommended to contact the service centers for the repair of iPhones.

If the phone does not charge, then there are obvious problems.

Using third party chargers

It is believed that third-party chargers can harm equipment, disable it and even lead to a battery fire. In most cases, this is a myth, since modern power supplies and USB cables have good characteristics of reliability and durability, regardless of the manufacturer and purpose.

Naturally, you should avoid chargers that are frankly cheap and of poor quality, even in appearance. They are usually passed off as originals from companies such as Apple or Samsung. Unfortunately, these manufacturers do not make or sell budgetary charges anywhere.

Unoriginal charging can damage your phone even more

What to avoid while charging your iPhone

There are several points that not everyone knows. For example, some people think that the phone should not be left on charge for a long time. In fact, this applies to very old models and these are not iPhones. Any Apple gadget, like other modern smartphones, has an internal chip that controls the entire charging process. When the cycle reaches its limit, it automatically stops supplying power and does not allow overcharging. The battery just stays in a dormant state, and the phone itself is powered by the mains.

It is better not to use the gadget while charging and let it go through the entire cycle. Of course, this will not bring any damage, but the process itself may take a long time. This is especially true when a person plays demanding games and simultaneously charges the iPhone.

Important! It is recommended not to use unstable or problematic devices while the iPhone is charging. They can cause short circuits or voltage surges in the home that the controller chip is sometimes unable to withstand.

Therefore, it is possible to charge the iPhone using other devices, but it is important to remember that sometimes it can be unsafe for both the phone and the person.

How to unscrew an iPhone 5 without a screwdriver

How to unscrew screws from an iPhone case if you don’t have a special screwdriver.

How to Unscrew iPhone Bolts At Home. INTEREST

How to unscrew the sprocket bolt if there is no special screwdriver

How do I open my phone? DIY screwdriver for all phones

How to open the lid of the Chinese iPhone 5s and iPhone (NO TOOLS)

How to remove any screw. BEST life hacks.

HOW TO REMOVE THE LOOSE SCREW (Secret Information)

How to disassemble iPhone 5s. How to open iPhone 5s.

The iPhone is considered a rather complex technique, but compared to other devices, it is easy to disassemble. This is good for the maintainability of the phone. After all, even an unskilled person is able to perform any manipulations with his gadget. True, this requires a set of special tools. But what if they are not at hand?

All the insides of the iPhone open if you unscrew the two screws located on the bottom of the device. With a special screwdriver, this action will take at most a minute of your time. But with a little bit of wits and a little more time, you can do everything without a tool. although the bolts have tiny threads, they are placed on the surface. Therefore, for unwinding, you can use a knife with a thin and sharp end. Other sharp objects such as needles, scissors and an awl are also used. Some go further and use women’s jewelry. Especially inventive people make absolutely wonderful objects. with the help of electrical tape and glue, they make the tip of a needle something like a screwdriver, but not everyone can afford it.

However, nothing is better than a knife, which has been proven by personal experience.

If you are interested in the topic of iPhone repair at home, then you must remember that you do it at your own risk. Not only does your phone lose its warranty after being disassembled outside an Apple service center. you can accidentally damage or improperly mount one of the gadget’s assemblies. Finally, Apple devices are quite difficult to disassemble on your own, manufacturers assume that you will only service them in branded centers.

If this warning did not scare you, and you are firmly sure that you want to learn how to disassemble an iPhone at home. let’s move on.

In this text, we will look at how to disassemble iPhone 4s, 5, 6.

We disassemble the iPhone 4s

First, make a backup copy of your iPhone, because you may need to restore it after assembly. ITunes will help you make a copy. Be sure to remember the order of disassembling the parts of the device, or better, lay out the parts of the phone strictly in the order that was during disassembly and take pictures at each stage. Pay special attention to screws of different sizes. they should also be left in an order that is understandable for you, so as not to get confused during assembly.

  • First of all, remove the SIM card slot and the card itself from the device. To do this, you need an original paper clip from the iPhone set, but if you don’t have one, a regular stationery will do.
  • There are screws on both sides of the charging connector. unscrew them.

The cover hiding the battery must be moved up and disconnected. To the left of the battery, in the corner, there is a small protective plate that hides access to it. Unscrew these two screws too.

Now you can see the connector that fits the battery. It must be carefully removed. Remove the battery by pulling on the small plastic tab.

In the upper left corner you can see an S-shaped protective plate held by 5 round screws. Unscrew them.

The protective plate hides six loops underneath, all of them need to be disconnected. Do not bend them or squeeze the cables too tightly.!

Five stubs are located on the surface and are completely visible, but the sixth is blocked and will be accessible after removing these five. Removing the leftmost ribbon cable allows you to remove the phone camera. At the same stage of disassembly, you will have access to the screw in the upper right corner, unscrew it.

When you remove the phone camera, remove three more screws. Two of them are located one above the other, under the plastic tab (which we used to remove the battery), and the third to the left, away from them. If you connect these screws with imaginary lines, you get. ⅃.

Now you come to take out the battery cable, it is relatively large, but to remove it it will be enough to lift it up.

Below, on the right, is the next screw to be removed. It is located at the very edge of the phone case. Now proceed to disconnect the antenna loop on the left. Its type is different from the previous connectors, but it connects in a similar way. This cable must be lifted carefully. After that, the antenna and ringer unit at the bottom of the iPhone will detach without additional effort. This is a black, elongated piece.

  • Pulling the orange cable aside, you will see another screw.
  • Unscrew the two pairs of screws. The first pair is at the bottom. Here, one screw was under the orange cable, and the second is located just above, on the right.
  • A second pair of screws are located at the top of the iPhone case. The first is next to the camera slot, in the upper right corner of the slot. The second is on the same level with the first, 3 centimeters to the right.
  • Thus, we freed the device’s motherboard and can dismantle it. Motherboard. a single block with circuits runs through the entire body of the phone. There is a washer-shaped piece next to the orange train and will need to be removed as well. Note that it is seated on double-sided tape, so it will take some force to detach. Do not overdo it!

    The next step is to remove as many as 10 screws holding the iPhone 4S module. Four of them are located in the corners, and the rest are located along the right and left edges of the iPhone frame. Note that the 6 side screws have a different size and the back has washers.

  • After this operation, there are still some screws left, but at this stage it is not necessary to disconnect them.
  • We carry out with a specially prepared instrument (pick, plastic spatula) along the screen so that it detaches.
  • To replace the display module with a touchscreen, the available description is sufficient.

    To replace the iPhone 4S Home button, slide the black latch to the right. If you want to remove the iPhone 4S Home button, slide the black latch to the right. It is located above the charging connector. By the way, you need to remove it too, for this you have to unscrew two round screws. It is now possible to remove the long orange train.

    The remaining connectors, including the cable from the phone start button (located on top) and the volume buttons will be disconnected if you unscrew the last screws.

    This video clearly shows how to completely disassemble the iPhone 4 and replace the screen.

    We disassemble the iPhone 5

    To do this, you need to unscrew a couple of small screws on opposite sides of the connector for charging the device. Finding them is not difficult at all.

    READ  It takes a long time to transfer data from iPhone to iPhone

    Next, using a vacuum suction cup, take out the screen. You can also perform the operation with a small plastic spatula or a pick. In this case, it is necessary to hook the screen from below, and then raise it. When performing an action, you need to be as careful as possible so as not to split or scratch the display.

    Also, the iPhone 5 often has a problem with easily erased paint. When disassembling the phone, you need to remember this at every stage of work.

  • After lifting the display, disconnect it from the main circuit block. the motherboard. Please note that the components of the device are quite tightly connected.
  • After unscrewing the last bolt on the board, carefully lift the screen cable. Here again you will need a pick or a plastic spatula. The screen can now be completely removed.
  • Dismantle the battery
  • In no case skip this disassembly step, because further actions with a connected battery may result in electric shocks. This is not only dangerous for you, but also causes defects in other parts of the phone.
  • The first step is to unscrew the three screws holding the protection on the battery cable
  • Use the same plastic spatula to remove the battery. The battery may not succumb to you the first time, but you shouldn’t worry about it. Gently pry it from different sides until the adhesive holding the battery comes off.

  • We take out and disassemble the motherboard of the iPhone 5
  • After removing the battery, unscrew the bolts that hold the camera. There are two of them. After that, we sequentially disconnect the microphone, speaker and headphone connectors. This is followed by the screws to which the antenna cable and SIM card slot are attached.
  • When you unscrew these 5 screws and disconnect the cables, slowly remove the motherboard.

    At this stage of disassembling the device, the iPhone 5 case can be postponed, because further manipulations take place directly with the motherboard. We remove the camera by unscrewing two screws. This unit does not have any additional fasteners and then freely detaches.

    We pass to the vibration motor, attached to three screws. Then, to remove the lower motherboard cable. To completely remove the bottom cable on the motherboard, which holds the Lightning port, headset jack, speaker, Wi-Fi antenna and one of the microphones, you need to unscrew seven more screws: two at the bottom next to the headphone jack, one in the right side of the loop and four more, directly holding the entire component.

  • Removing the CPU
  • To separate the iPhone 5 processor, you first need to remove the protective film from it.
  • Removing the details from the front panel.
  • When you have removed the remaining elements from the back of the machine, you can go to the front.
  • The “home” button is held on the glue, the button must be gently pryed off with a spatula and removed
  • One of the last pieces to be detached is a metal plate that protects the screen from touching other hardware parts of the device. After the last part is removed, the iPhone 5 disassembly can be considered complete.

    In this video, you will learn more clearly how to disassemble the iPhone 5

    IPhone 6 disassembly

    Good news: iPhone 6 is easier to assemble and disassemble than its predecessors. This is undoubtedly due to the fact that the device has become thinner, but larger. Thanks to these changes, parts are easier to access and are housed in a more spacious enclosure.

      The screen of this device is held by two screws of the “pentalobe” type; to unscrew them, you will need a special screwdriver, about which we will say a few more words.

    Removing the display carefully with a suction cup.

    Using a suitable PH screwdriver, unscrew the metal protection blocking access to the loops. Until we remove it, we will not be able to pull out the screen. It is necessary to disconnect the metal plate that presses the cables and prevents the screen from being removed completely.

    The camera and the earpiece are placed on one cable, we disconnect them.

    We disassemble the display, it is necessary to remove the protective plate from it.

    The battery, as on previous models, is held in place thanks to double-sided adhesive tape. Use a plastic spatula to pry it from all sides until you can remove it. But be careful and careful.

    We take out the rear camera with tweezers

    After that, you should go to the polyphonic speaker.

    The charging connector on the iPhone 6 is located together with the audio connector on the same flex cable, so they cannot be replaced individually.

    Using tweezers, we separate the cable of the phone on / off button, volume and mute.

    You can watch a more detailed disassembly of the iPhone 6 in this video.

    I would like to add a few words about the special tools that will be required to disassemble Apple smartphones.

    As we have already found out, we cannot do without:

    • Sucker
    • Plastic pick or special paddle
    • Tweezers
    • Special screwdriver set

    It is on screwdrivers that I want to dwell in more detail, let’s look at what characteristics and design they must have in order for iPhone disassembly to go smoothly.

    As an example of the optimal set of screwdrivers for electronics repair, we suggest considering a set of bits for precision work with a holder, manufactured by VIRA.

    First of all, the holder. It is made of impact-resistant plastic and has a rubber coating for easy grip. The holder is 11 cm long and can be wrapped in the palm of your hand without being too long.

    Traditionally, for such holders, it is considered important to have a rotating platform. You can push down on the tool and the body can be easily rotated with your fingers.

    • 25 mm SL1.5,
    • SL2.0, SL3.0
    • PH000 , PH00 , PH0 , PH1
    • T4, T5, T6, T7, T8, T10, T15, T20
    • H2.0, H4.0
    • PZ1 , PZ0
    • 0.8, 1.2, 1.5, 2.0
    • ▲, 2.0, 2.3
    • Y 2.0mm, ∪2.6mm
    • ⊙1.0

    The listed types of bits easily allow you to repair any unit of Apple devices, including the “pentalobe” slot.

    Particular attention should be paid to the material of the bits and their additional processing. The material is used with a high hardness so that the tips do not wear off over time, or wear less.

    VIRA bits are made of chrome vanadium, a hard and durable material.

    Since iPhone disassembly is a constant work of small parts and small hardware, it is best to have the bits with a magnetic tip. So it is easier to pick up the fasteners, place them in the hole in the smartphone case.

    Particular attention is paid to the placement of the kit in the package. Each bit is in its own cell, they are fixed immovably and do not mix when carrying the kit. The box of the kit is made of high quality hard plastic that can withstand a drop to the floor from a height of human height.

    For additional storage convenience, the box has a retractable hook at the back. Thanks to this, the kit can be hung on the wall.

    How to disassemble iPhone 5s at home

    One Three F Three F again C! Four Four again! And one more C! Five! C! Five?! C!

    Fortunately, Apple is in tech, not education. We can only imagine how confusing the ABCs would be if they studied in Cupertino.

    Weird names aside, we were eager to bite into the newest phone fruit. So passionate that they sent one of us to the land where they walk on our heads to get one.

    We also have special articles on replacing frequently-breaking iPhone components: replacing the iPhone 5S screen, replacing the iPhone 5S battery and replacing the home button.

    A warning

    This article is not a guide to action! You are solely responsible for collecting and disassembling your device. Many manufacturers do not carry a warranty if the device has been disassembled by the user. If you do not want to void the warranty for your device, check the warranty conditions in the documentation or with the device manufacturer.

    Used tools

    TS1 pentalobe screwdriver
    PH000 Phillips cross head screwdriver
    Sucker
    Plastic tool for disassembling bodies “shovel”

    New iPhone is a journey into the future. iFixit disassembly team moved 17 hours ahead of time to get their hands on the iPhone 5S early.

    We want to say a big thank you to our good friends at MacFixit Australia for allowing their Melbourne office to be used for this review. They sell Mac / iPhone accessories and iFixit tools.

    To close all our backs, we learned from our best linguists that 5S upside down is still 5S.

    Talking about tools. For this analysis we will use our brand new Pro Tech Screwdriver Set.

    While we prepare ourselves to dive into the wonderful internals of the iPhone 5S, let’s go over the technical specifications:

    • Apple A7 processor with 64-bit architecture;
    • Co-processor for motion analysis M7;
    • 16, 32 or 64 GB Flash memory;
    • 4-inch, 326 ppi retina display;
    • 8MP iSight camera and 1.2MP FaceTime camera
    • Fingerprint scanner built into the home button.
    • Available in three colors: space gray, silver and zoooooloto (or, as we call it, not-space-color at all, a medal for second place, and Bling!).

    iPhone 5S Take Apart Repair Guide

    Apple follows its tradition of shielding the user from the inside of the device using pentalobe screws. Luckily, we were ready for this. We’ve Released Our Reliable iPhone 5 Freeing Kit and Surprisingly, It Works!

    Unfortunately, we did not purchase the paint we needed, so the kit contains only silver and black Philips Phillips screwdriver screws.

    We are now pressing our designers to design Phillips screws in 585 gold. They will cost 50 each, and will turn on the first attempt to unscrew them, so they will be perfect for the iPhone. We will keep you informed.

    Our released iPhone 5S reminded us of another iPhone with polka dots, a breakdown of which will be published in the near future

    We finish spinning in place. It’s time to open the baby! Just like last year, we called for help from the suction cup to separate the display module assembly from the case.

    Unlike last year, we gently run a spatula around the perimeter, just in case

    The paddle helped. At the bottom of the phone, a ribbon was found connecting the Touch ID sensor located in the home button and the Lightening connector.

    This adds a small element of danger to the parsing process. If you lift the screen too high by the suction cup, then there is a chance to damage the cable.

    We survived the first trap and carefully detached the Touch ID ribbon connector using a spatula.

    Alas, at first glance, the internal structure of the iPhone 5S does not differ much from the internal structure of the iPhone 5. The main difference is the lack of a tongue on the battery, for which it can be taken out of the case.

    With the help of our favorite set of screwdrivers, we removed some of the metal shields that protect the connectors and embarked on an epic battle with the battery.

    Seemingly insignificant, the lack of a tongue on the battery revealed a much larger problem. the glue.

    Perhaps the letter es in the name means “stuck together” or “put up with” like, “this battery stuck to the body tightly” or “I hope you don’t want to replace the battery and put up with the fact that you have an old one.”.

    While we dreamed of a battery in the iPhone that could be replaced without tools, we heated the existing battery and pried it with a spatula.

    Holy Scotch! It seems that Apple in the previous “five”, compared to the iPhone 5S, did not use double-sided tape at all! There are two hefty white “runways” that hold the battery almost throughout its entire area.

    Addition: some guys report that this tape has good tear-off. As soon as we receive more iPhones for repair we will check this theory and inform you!

    The iPhone 5S is said to have up to 10 hours of talk time on 3G, but there are rumors that iOS 7 won’t leave a chance.

    The gold battery by Desay Battery Co., Ltd, made in China in the city of Huizhou, gives out 3.8V, 5.92Wh, 1560mAh. For comparison:

    • iPhone 5: 3.8V, 1440mAh, 5.45Wh. Talk time up to 8 hours in 3G networks. Standby time up to 225 hours.
    • Samsung Galaxy S4: 3.8V, 2600mAh, 9.88Wh. Talk time up to 7. Standby time up to 300 hours.
    • Motorola Moto X: 3.8V, 2200 mAh, 8.4 Wh. 24 hours in “mixed mode”.

    It looks like different phones come with different batteries. Our other space gray device was powered by a battery from Simplo Technology Inc. (on right).

    After successfully extracting the battery, we move on to the next step on our journey into the bowels of the iPhone: removing the (permanent) 326 dpi retina display assembly.

    A few sweeps with the spatula to disconnect the ribbon cables from the FaceTime camera, sensor, and screen, and the display module is free.

    Looking for display specifications? Not worth it! You can look at the technical characteristics of the display in the previous “five”. Despite the trend followed by other smartphone manufacturers, the screen in the iPhone 5S is no bigger, no better, no worse than the screen in the “top five”.

    We quickly removed the home button and Touch ID sensor, Apple’s new fingerprint scanner. Time to knock out fingerprints!

    CMOS chip, obviously the Touch ID is a set of small capacitors that create an “image” of irregularities on the surface of your finger.

    The technology is developed by AuthenTec and was acquired by Apple about a year ago. Fingerprints are reportedly stored locally on the device, which means they won’t be seen in Cupertino.

    READ  How to change iPhone name in settings

    We’re worried about whether the sapphire crystal will protect the sensor from degradation over time, which is common with many CMOS fingerprint sensors. If not, it could become a ticking bomb, just like a super-glued battery.

    Opening the iSight camera. DNL333 41WGRF 4W61W printed on the back of the camera.

    According to our friend Jim Morrison, VP of Technology Analysis Group at Chipworks, “The DNL markings match the markings on the Sony IMX145 cameras that we saw on the iPhone 4s and iPhone 5. The markings on the ends are different, but our insiders say it’s a camera again. manufactured by Sony “.

    Apple has stated that the pixel spacing on the sensor is 1.5 microns. Thus, this is not an IMX145, but some kind of new version. The bottom of the camera module is marked AW32 65BD 4511 b763.

    For those of you who are counting steps and comparing everything to the previous model. while everything is the same.

    A great example of Apple’s iterative design. The iPhone 5S has everything more combed and optimized.

    Gone are the pathetic antenna adapter, reducing the number of elements that can disconnect or break.

    If only they had decided to move the antenna connector from bottom to top

    We found a Murata 339S0205 WI-FI module (based on the Broadcom BCM4334 chip, according to Chipworks).

    • Murata IC seems to be the same for both iPhones.
    • The design of the motherboard is identical, but small differences (for example, marking 94V-0 on the board on the right, absent on the board on the left) may indicate that Apple manufactures motherboards in different factories.

    Removing electromagnetic screens! Behold the integrated circuits:

    • SK Hynix H2JTDG8UD3MBR 128 Gb (16 GB) NAND Flash;
    • Qualcomm PM8018 RF power management IC;
    • TriQuint TQM6M6224;
    • Apple 338S1216;
    • Broadcom BCM5976 touchscreen controller;
    • Texas Instruments 343S0645 touchscreen interface;
    • Skyworks 77810.
    • Skyworks 77355;
    • Avago A790720;
    • Avago A7900;
    • Apple 338S120L.

    Super-big thanks to the guys at Chipworks who helped to discover and identify these wonderful microcircuits.!

    Let’s move our attention to the back side of the motherboard:

    • Apple A7 APL0698 SoC (based on this MacRumors post, the markings F8164A1PD indicate the RAM is likely 1GB);
    • Qualcomm MDM9615M LTE Modem;
    • Qualcomm WTR1605L LTE / HSPA / CDMA2K / TDSCDMA / EDGE / GPS transceiver.

    While trying to locate the expected M7 coprocessor, we started to wonder if it is in a separate package or is part of the A7.

    Perhaps the “M” stands for “magical,” and Apple uses magic dust to keep the device working. Or maybe “M” means “marketing”

    It’s time to check out the new kid on the block, and he’s as cool as the A7. In addition to the fingerprint sensor, the A7 is the main feature for which it is worth choosing the iPhone 5S over the iPhone 5C.

    According to advertisements, the A7 is twice as fast as its predecessor, the A6, which was used in the iPhone 5 and iPhone 5C.

    The move to the A7 marks the first use of 64-bit processors in smartphones. Based on a report by AnandTech, the performance gains in the A7 do not come from the move to 64-bit architecture, but from the move from the legacy ARMv7 instruction set to the newly developed ARMv8.

    The modern ARMv8 instruction set has been specifically designed for 64-bit architecture. It got rid of junk support, which increased efficiency, improved performance without affecting battery life.

    We’ll have to wait while we examine the insides of the chip to find out who made it.

    Several screws secure the 1.2MP FaceTime camera in place. Increasing the pixel size of an iSight camera may get a lot of attention, but DIY paparazzi is what makes iPhones what they are.

    The bottom of the 5S looks almost the same as in the “five”, although the speaker assembly is easier to remove.

    With the speaker removed, the module with headphone jack, microphone and Lightning connector can be easily removed.

    On previous generations of the iPhone, many components had to be replaced at once. the design was not so modular.

    Found another novelty: double flash.

    The old and amber LEDs are located next to the camera to help combat the pale tones of nightlife photography.

    Just like the iPhone 5, the display assembly comes off first, making it easier to replace.

    The battery is also easy to access, although it is not “user serviceable”.

    Fingerprint sensor cable can be easily torn if careless when removing the display.

    iPhone 5s still uses Pentalobe head screws, requiring purchase of a dedicated screwdriver.

    Protective glass, screen and sensor are one component, which increases the cost of repairs.

    IPhone 5s Repair Ease: 6 out of 10 (10 is easiest to repair).

    The assembly is carried out upside-down. Thank you for your attention

    I recommend some more interesting things:

    If you liked it, please do not be lazy to click “I like” or “share” or “1” just below, or post a link to the article in your blog or forum. Thank you

    You can rate this article: Download.

    Our friends from the MacPlus service center are constantly preparing materials for us on how to properly perform certain actions to repair your favorite Apple equipment. This time, the masters managed to disassemble the latest generation of iPhone. iPhone 5. Step-by-step instructions are already here.

    To maintain our high level of Apple repair, we buy new products almost immediately after they enter the market and disassemble them. The new iPhone 5 is no exception.

    What you need to parse:

    • Pentalobe screwdriver, like for iPhone 4s (good news)
    • Suction cup for lifting the screen
    • Small Phillips screwdriver
    • Scapula
    • Accuracy and iron nerves (after all, the device costs a lot)

    So, the subject is ready to parse, let’s proceed.

    First of all, unscrew the external Pentalobe screws with a screwdriver. Nothing new.

    We take the suction cup and raise the screen. Here we include attentiveness and accuracy. Most likely, during the first parsing, it will be necessary to pry the display with something thin, but you can scratch the aluminum.

    We unscrew the screws for the protection / fastening of the cables.

    Disconnect all cables and antenna connectors and remove the display. When working with loops, it is better to use a plastic spatula.

    We unscrew one more protection of the cables. this time in the middle of the motherboard.

    The first thing to do with any analysis is to disconnect the battery. In the fifth iPhone, this will not work right away, so let’s turn it off now.

    We remove the battery. It is glued to the body, so you need to pry it off with a spatula.

    We got to the motherboard. First, unscrew the two screws securing the camera.

    Disconnect the speaker cable, microphone, headphone output and Lightning connector (the so-called “Tsar-Loop”).

    We remove the SIM-card tray. We recommend that you do this before parsing, but at this stage it is necessary.

    Disconnect the cables connecting the motherboard and the back panel (at the top of the panel).

    Almost everything is ready to remove the motherboard. Disconnect the cables that interfere, unscrew 5 screws.

    Ta-dam! Motherboard detached from back panel.

    On the motherboard, unscrew the two screws from the camera protection and disconnect the camera.

    This is how the motherboard looks like without other details. Slightly reminiscent of 4s.

    We unscrew the three screws holding the vibration and detach it. Vibro, again, is very similar to the one in 3gs, 4 and 4s.

    I would like to say that inside the new iPhone is a kind of synthesis of 3g / 3gs and 4 / 4s. It is much easier to disassemble than the previous model, so it probably won’t be very expensive to repair the iPhone 5. You can always buy spare parts and repair your iPhone 5 at the MacPlus Service Center!

    IPhone 5 and 5S owners are wondering how to disassemble the phone. Time does not spare even the best devices: the panel may get worn out (especially on black models), the sensor fails, and those who like to “swim” have problems with the hardware. To replace iPhone parts, you need to know the internal structure and be able to disassemble the device.

    • a five-blade Pentalob screwdriver (without it, the bolts are unlikely to give in to you);
    • Phillips screwdriver;
    • vacuum suction cup;
    • plastic spatula for disassembling the case (or something similar).

    Professional set

    The first thing we need to do is unscrew the two screws at the bottom of the case, on the sides of the Lightning connector. The iPhone 4 used Phillips screws; in later versions of Apple, developers began to use special five-blade Pentalob bolts to prevent self-disassembly of phones.

    Unscrew the first two screws at the bottom of the panel

    If you do not have a special screwdriver for them, you can try using a five-pointed star or take a flat one and file it with a file on the sides. But be careful, if you use non-standard tools, you can grind off the bolt heads. Just in case, it’s better to stock up on bolts of the same size, but with a cross-shaped head.

    Using a vacuum suction cup, slightly lift the screen, helping ourselves with a plastic spatula. Why a spatula and not a screwdriver? This reduces the chances of damage to the iPhone’s case or screen. This can be done without the help of a suction cup, by picking up something (some use a needle) the top panel, but you need to be extremely careful.

    Raising the iPhone screen

    Carefully lift the screen from the side of the Home button. At this step, the first differences between models 5 and 5S appear. On iPhone 5, the bezel just lifts up to an almost right angle with the body.

    Raising the top panel on the iPhone 5

    The situation is more complicated on the iPhone 5S. The screen is attached to the motherboard with a ribbon cable, so you shouldn’t lift it up sharply. It is necessary to disconnect the loop before further work using a plastic spatula. And after that, raise the screen, as in version 5.

    Disconnecting the ribbon cable on the iPhone 5S

    To completely detach the screen, use a Phillips screwdriver to get rid of the two screws that hold it.

    Unscrew the top panel bolts

    A plastic spatula will help get rid of the top panel

    The iPhone is divided into two parts, each of which can be disassembled into several more components.

    iPhone is split in two

    Let’s pay attention to the display panel. Unscrew the “Home” button. It is the same in both models.

    Remove the “Home” button

    At the top of the dashboard, the 5 and 5S are different again. The 5S has a camera, proximity sensor and speaker fixed there, which are removed after removing the mounting plate.

    iPhone 5 Full Disassembly Guide

    Top panel of iPhone 5S

    On the 5th version of the iPhone, the mount has a hearing speaker, which is held by two screws and spring contacts. The front camera can be simply removed if necessary, it is held on a ribbon cable.

    The speaker on the iPhone 5 is screwed on firmly

    The last step with the front panel is getting rid of the metal protection.

    The front panel loses its protection

    Let’s move on to the body of the device. The first step is to get rid of the battery so as not to get an electric shock. Disconnect the ribbon cable from the board with a plastic spatula.

    Disconnecting the battery from the motherboard

    With the same tool we pry on the battery and pull on the label (in 5S it is absent, so we use only a spatula). If the battery does not give in the first time, you do not need to be scared, it is glued. The glue is not too strong, so the battery will easily give in with a little more effort.

    Getting rid of the energy source

    Disconnecting the main camera in version 5. It is held by two screws, after removing them the camera is free. In 5S, she is in this state initially.

    Cameras iPhone 5 (left) and 5S (right)

    The next step is to remove the motherboard. There is no difference between the iPhone 5 and 5S. Disconnect the antenna connector module from the motherboard. We unscrew the screws securing the board to the case and the contacts at the inner wall. Carefully take out the motherboard.

    Motherboard attaches securely

    There is a processor on the motherboard: A6 for 5 and A7 for 5S. When disassembling for the first time, you will need to remove the protective film.

    Remove the protective film and then the processor

    Let’s continue to disassemble the case. In its lower part there is a headphone jack, a speaker, a Wi-Fi antenna (in version 5) and a lower microphone. all this is attached to the Lightning connector. We get rid of the mass of glue with a plastic spatula.

    Removing the Lightning connector and everything that comes with it

    All components of this connector can only be replaced when soldered, so it can be costly to break it.

    Lightning separate from iPhone

    At the top of the smartphone there is a vibration motor for a call, Wi-Fi and GPS antennas.

    Remaining parts on the top of the case

    As a result, we get a disassembled phone. You can assemble your device back by following the same instructions in reverse order.

    IPhone 5 fully disassembled

    IPhone 5S fully disassembled

    • You are solely responsible for assembling and disassembling the device. If in doubt that you will succeed, take it to the service center. the masters will help.
    • When disassembling the device yourself, remember the warranty period. After you open the case yourself, the warranty is automatically lost, subsequent repairs will take place at your expense.
    • Do not spare funds for special tools: they will cost less than repairing or buying a new phone.
    • Do not make any sudden movements, you can tear off the cable or break especially fragile parts of the iPhone by your inaccurate actions.
    READ  iPhone screen black and white what to do

    When creating the iPhone 5 and 5S, Apple went to great lengths to make sure they couldn’t be easily disassembled. This process will take a long time, but it is within the power of an ordinary person. If you are confident in yourself, you can try to disassemble the iPhone at home on your own, otherwise. take the device to a competent master, he knows exactly what to do.

    Preparation

    Before starting disassembly, you should perform a few simple steps:

    • create a backup copy of your data. you can use iCloud or iTunes for these purposes;
    • remove the cover or screen protector;
    • it makes sense to disable the iPod lock function.

    All this will help to save data and resume the iPod after assembly.

    Used tools

    You will need the following disassembly tools:

    • A hot air gun is indispensable for softening the glue in the joints.
    • To open the iPod case, you need a special hard plastic tool.
    • A thin Phillips screwdriver is needed when you need to remove the Phillips screws.
    • Some of the iPod connectors are not soldered to the board, but you will still need a soldering iron, for example, to replace the battery.
    • You may need a piece of a thin metal strip or a scalpel to separate the glued cable.

    Disassembly instructions

    First, the touch screen is warmed up with a hot air gun, we dismantle the iPod completely only after this step. The adhesive that holds the display module will soften when heated.

    After that, using a plastic tool, the iPod case is opened around the perimeter.

    After that, you need to unscrew all the screws and carefully loosen, so as not to break the loop, the electromagnetic shield. Some parts can be removed without soldering, such as the headphone jack. You only need to unscrew the screw and disconnect the ribbon cable from it.

    The iPod motherboard, battery, and display are one piece and must be removed completely. This is hindered by the headset button cable, which is soldered to the motherboard on one side and glued to the case on the other. But you can still do this if you carefully separate the cable from the case with a scalpel.

    By separating all copper strips of the cable from the housing and touch panel, you can remove the copper shield adjacent to the battery. After that, the motherboard is disassembled. Using a plastic tool, you can detach the iPod display module, rear and front cameras, external antenna from the motherboard.

    At this stage, you can already get to the chips, so the disassembly can be considered complete.

    How to disassemble ipod touch 5?

    Apple iPod touch 5th generation is the best music player on the market. In fact, this is the same iPhone 5 only thinner and without a SIM card module. But just like any other gadget, iPod touch can break and become unusable.

    In order to bring the device into working order, you need to disassemble it. But how can you do this? After all, the iPod does not have a single screw and the case seems to be non-separable. In this article, we will show you how to disassemble an iPod.

    We begin disassembly. To do this, we need a whole set of tools and, preferably, an industrial hair dryer (a regular one will also work). The iPod touch is similar in design to the iPad. The fact is that the front panel with the display is attached to the rest of the case with special glue. Therefore, a set of tools from an iPad or iPhone is also suitable.

    So, let’s start disassembling the player. We warm up the front panel with a hairdryer along the entire perimeter. Then, with a plastic spatula, carefully lift the structure with the display, but do not make sudden movements, as you can damage the train. You cannot detach the screen right away. There is a frame on the front panel, on which latches are located around the perimeter to secure the components during dismantling.

    Next, we remove a special plate that protects against overheating, unscrew a few screws.

    Next, you need to disconnect the display cable from the motherboard. It will not work simply to do this, since the connector that connects the board and the display is inconveniently located. You will have to do this procedure by weight.

    Then we remove the Wi-Fi module. With a plastic spatula, simply disconnect it from the board.

    We continue dismantling, removing the structure, which is combined into one loop. It contains: a camera module, flash, microphone, volume and Power buttons. If at least one part of this structure breaks, then everything will have to be changed together, except for the camera, it disconnects by itself.

    If the problems were in the display or the Home button was faulty, we disassemble the screen module. But you can only remove the Home button here, since the glass and the display are a single structure, to avoid dust.

    Removing the battery is easy. Just pick it up with a plastic spatula and take out.

    To remove the motherboard, you need to disconnect the Lightning module. To do this, unscrew the four screws.

    iPod touch 5th generation completely disassembled. Now you can easily replace the defective part and save money on the service center.

    This time the specialists of the iFixIt laboratory got a new player Apple iPod Touch 5th Generation 16 Gb. This version of the player can be called a bit stripped down or budget. Unlike the standard versions of the device, this iPod is sold only in the 16GB version, and it also lacks the main 5-megapixel camera, the color is only silver, and there is no hole for attaching a strap. Otherwise, no significant differences were found. Of the internal changes, a change in the location of the microphone and some modification of the grooves for laying the cables were noted, which apparently was done due to the absence of the main camera.

    • 4-inch widescreen IPS Retina display
    • Apple A5 dual core processor, 4GB (512MB) DDR2 RAM
    • 802.11a / b / g / n Wi-Fi (802.11n 2.4 and 5 GHz) Bluetooth 4.0
    • FaceTime HD 1.2-megapixel camera capable of capturing high-definition video (720p) up to 30 frames per second
    • Three-axis gyroscope and accelerometer
    • 16 GB flash memory

    As a result of disassembling the device, the specialists did not encounter any surprises, the result was predictable, the iPod scored only 3 points out of 10 possible on the device maintainability scale.

    It is quite difficult to open the case without damaging the device, the battery can be removed quite simply, many of the internal components are glued together in one way or another, which greatly complicates their repair. The touch screen is fastened with screws plus glue, due to this, it is difficult to remove it, it also applies to most of the cables.

    The result is 3 out of 10, so at home, without special tools, it’s better not even to try to disassemble the iPod yourself. Repairs are best done at authorized service centers.

    The iPod Touch 5 was brought in for repair with a breakdown. “does not charge”.

    The fastest thing to do is to change the bottom cable with the charging socket.

    It is very difficult to disassemble, repair and even diagnose such a breakdown in such a device:

    • To disassemble, you need to peel off the display;
    • Replacing the socket is accompanied by soldering three loops with a large number of contacts;
    • Diagnostics is obtained so that you can only do if you replace the bottom cable with a charging connector.

    We remove the screen with heating and a spatula. It is glued at the bottom and top. Center. latches.

    We unscrew the metal plate and we are inside 🙂

    We unsolder the battery cable using a fusible alloy “rose” and a soldering iron.

    We unsolder the old cable from the board using the same “rose” alloy and solder a new one.

    To check for a short circuit between adjacent contacts (the tin can spread out), draw the contacts.

    We connect the display and solder the battery.

    iPhone 5 Teardown. Step by step complete disassembly directions

    We rearrange the socket mount from the old to the new.

    Wanting to find differences from previous generations, the iFixit team first looked into the new nano. We found a flash memory from another manufacturer and a processor with a changed marking. iPod touch, in general, did not bode well either, but hope dies last iFixit draws our attention to 4 differences that are just worth mentioning: Possible upgrade for the chip of wireless interfaces Wi-Fi and Bluetooth, Murata RV KM1721006; New marking (wow!) On the Apple A4 processor. VT1K3441AQ versus last year’s K4X2G643GE; New AGD8 2131 gyroscope; The 2129 33DH chip next to the gyroscope appears to be mounted on the same substrate as the gyroscope from the 4th generation iPod touch. The only significant innovation for the iPod touch is the white model. The question is, why didn’t Apple start producing a white front panel sooner? Excuses about the lack of technology will no longer help, since the white iPad 2 and the at least white iPhone 4 have been released since spring. The fact is that the Cupertinians simply could not do the same with the iPod touch. Otherwise, they would have nothing to say about him on October 4th! And having reached the autumn, they thereby presented the situation in a favorable light for themselves

    Disassembly of the Ipod Touch is needed in case of replacement of faulty parts or the need to install a replaceable battery. This operation is relatively simple, especially in comparison with the disassembly of some earlier models, but it requires the utmost care. Please be aware that opening the iPod will void the manufacturer’s warranty. Responsibility for possible problems is assumed by the owner.

    Before disassembling the iPod, you should prepare all the necessary tools and a workplace by removing all unnecessary and dusting the table. Good light will help you act with confidence. Use a special magnifying glass on a movable tripod.

    Safety engineering

    Handle the battery with care. Excessive pressure or overheating can cause an explosion and fire. When replacing, use a battery of the same brand.

    All iPod cables are thin and easily damaged, especially because they are firmly adhered to the glue in some places. In this case, you can use a hot air gun and scalpel. When disconnecting iPod modules connected by a ribbon cable, gently pull them apart without sudden jerks.

    The front glass and LCD panel are soldered to each other, so they are completely replaceable. You shouldn’t try to separate them.

    What to do if your iPod won’t turn on after assembling

    The assembly is carried out sequentially, the steps are performed in the reverse order of disassembly. You should test your iPod as soon as it is assembled. If the player does not turn on, you can try to remember which of the actions during assembly was done incorrectly or was skipped. In this case, you should carefully disassemble the iPod again and then carefully go through all the assembly steps. It makes sense to record the disassembly process on video.

    If any part is damaged, contact a specialized workshop to have it replaced.

    How to disassemble iPhone 5.instructions

    For most users, the question of how to disassemble the iPhone 5 is of purely academic interest. This is relevant exclusively for employees of service centers. Disassembly with the help of a hammer and some mother (more precisely, the tip of a knife), so beloved by home-grown “masters”, will surely ruin the device.

    What you need to disassemble the iPhone 5

    The list is short enough: Pentalobe screwdriver; Small cross screwdriver; Suction cup for lifting the display; Paddle.

    Iron nerves (considering the cost of the device) and accuracy can be added to the list. The program for the Android firmware is definitely not needed, since the iPhone does not work with this operating system.

    Unscrew the external screws with a Pentalobe screwdriver. 2. Raise the screen with a suction cup. When disassembling it for the first time, you will most likely have to pry it with something thin, but there is a risk of scratching. 3. Unscrew the screws for securing / protecting the cables. 4. We disconnect the antenna connectors and all the cables, remove the display. A plastic spatula is used to work with loops. 5. Unscrew the cable protector located on the motherboard, on which the Navitel for iPhone can be installed. 6. Disconnect the battery and remove it. It is glued to the body, so we separate it with a spatula. 7. Unscrew the two screws holding the camera. 8. Disconnect the cables of the microphone, speaker, Lighting connector and headphone output. 9. Remove the antenna cable. 10. Remove the SIM card tray. It is recommended to do this before disassembly, but is required at this stage. 11. At the top of the rear panel, disconnect the cables that connect the motherboard to it.

    At the next stage of disassembling the iPhone, you can remove the motherboard.

    You can remove the motherboard by disconnecting the interfering cables and unscrewing the screws that hold it. 13. Remove the camera by unscrewing the two screws securing the camera to the motherboard. 14. Unscrew the three vibration retaining screws and remove it. 15. Unscrew the screws near the headphone jack: two next to it, and one to the right of the bottom cable.

    After unscrewing the 4 remaining screws of the lower cable, remove it. That’s all you need to do before disassembling your iPhone.

    As you can see, the disassembly process is extremely difficult, so it is highly discouraged to repeat it in whole or in part at home.

    BYRGPUB.COM 2021