Connect your audio system to your new TV

Want to get a surround sound effect? Good news for you: connecting your speakers is no problem because you can connect either a digital audio cable or an HDMI cable to the One Connect Box!

Via Ethernet

Many device models support a direct connection to the network, this option is more advantageous, since, unlike a wireless connection, it is more stable. You can connect the set-top box with a router via a local network using an RJ-45 cable.

To carry out the procedure for connecting via Ethernet, do the following:

    Using a LAN cable, we connect the set-top box and the router.

    connect, set-top, samsung
  • We go to the media player menu, where we are looking for network settings.
  • We choose the type of network. wired connection (the same option can be called “Cable” or so on.).
  • Press the connect button.
  • As a rule, the procedure is performed automatically after pressing the corresponding button, but in some cases it may also be necessary to enter information about your IP.
  • The basic setup is complete, the Internet is connected and now you have to install applications, games, etc., if there is such a need, or enjoy watching content.

    Actions for media player problems

    If during the procedure there are problems and the device does not want to connect to the network, freezes, slows down, reboots, etc., resetting to factory settings can help. This procedure erases the user’s files from memory, but the pre-installed applications and other data that are available on the Smart-Box by default will remain in place. There are two reset options for Android box, the first one implies the following actions:

    • We go to the settings of the media player, where we find the section “Restore and reset”. Some models allow you to back up before resetting, so application data, passwords, etc. will be saved.
    • Click “Reset settings”, mark whether to format the memory card or not, and click “Reset data”. The device will be turned off and after a while it will be restarted.

    The second option is used when there is no access to the STB settings menu:

    • On the device case, you need to find the “Reset” or “Recovery” button (if there is none, the button is hidden in the AV-out and pressed with a match).
    • Press and hold the button, then disconnect the power cable from the media player, and, while continuing to hold the reset button, after a few seconds reconnect the power.
    • The screen should blink, signaling a reboot, then release the “Reset” button.
    • In the boot menu that appears, select Wipe Data Factory Reset and click “Ok”.
    • Now click Yes. Delete all User Data, agreeing with what is happening in the process of deleting user information.
    • After a few seconds, the main menu will appear, where we select the item Reboot system now.
    • After a few minutes, the system will reboot.

    These actions will be effective in case of system errors on the device. After performing a factory reset, you will have to re-configure your Smart TV set-top box.

    Just plug and play for video consoles

    When you’ve gotten the latest game console or new media player, you’re in for the fun right away. Well, QLED TV is about to change your life. Here’s how to connect your DVD player to your TV (or Blu-ray!) Connect its HDMI cable to the One Connect Box. This is it. Or, if you’re wondering how to connect your gaming devices to your TV, it’s the same thing. Plug in the One Connect Box and get ready to win. It’s that simple!

    Wait What is One Connect Box?

    Have you met yet? Let me introduce you to your new best connection friend. Pick up an invisible connection and follow it to the end. There is no pot of gold, but QLED TV does have a One Connect Box, a small port box that sits at the end of an invisible connection. § This is what allows you to move devices out of sight. Let’s see what else you can connect to One Connect Box.

    Setting up Smart Hub

    Turn on your Samsung Smart TV. Press Menu on the remote control, select Network, AllShare Settings and then Content Sharing.

    Find your computer in the list of devices. Select a device with a remote control to allow it to play media on your TV.

    Press the Smart Hub button on the remote control. Select “Photos, Videos & Music” at the top of the Smart Hub screen.

    Select a media type, for example Video, and select your computer in the list of network devices. Open folders, find the video you want to play on TV and select it to play.

    How to connect a Smart set-top box to a TV

    For the functioning of the media player, it is necessary to ensure its connection to the TV, organizing communication not only between them, but also providing access to the network using a wired or wireless connection. Despite the large number of models, figuring out how to connect a Smart set-top box to a TV is not difficult, even a not too advanced user can handle this, the process is not complicated.

    Typically, the device is connected to a TV set via HDMI, the connector is present in the arsenal of modern models, sometimes the set of the media player includes an HDMI-AV converter, in case it is connected to an older TV. The coaxial cable connected to the HDMI port has a high bandwidth and is capable of transmitting high quality digital signals, which cannot be achieved when the video signal is transmitted over twisted pair. This fact must be taken into account in advance, even before buying a receiver.

    The device is powered by an adapter connected to an outlet, or can be supplied from the TV itself when the Smart TV set-top box is connected to it via USB.

    The procedure for connecting a Smart TV set-top box to a TV is as follows:

    • We de-energize both devices. We do not just turn off, but also remove the plugs from the sockets. If the set-top box is powered not from the mains, but from the TV receiver, turn off only its power.
    • There are not many options on how to connect the media player to the TV, it all depends on the intended design option. Or we take the HDMI cable and connect it with one end to the corresponding port on the receiver, and the other into the TV receiver connector, or connect it via USB (port 2.0 or 3.0) using a USB cable. In the case of a TV stick, it’s still easier, we insert it into the TV port like a USB flash drive.
    READ  How To Connect The Camera As A Web-Camera
  • If the TV set is old and does not have an HDMI connector, you can only connect a set-top box that uses three composite outputs (“tulip”) or an AV output. Alternatively, you can use an HDMI-AV converter. In this case, a converter is connected to the TV with the help of “tulips”, after which the set-top box is connected to it with an HDMI cable.
  • We turn on both devices.
  • How to Connect Samsung Smart TV to Alexa

    Configure devices.

    How to Connect a TV to a Cable Box

    First, make sure your Samsung TV and Amazon Alexa are set up and working, After completing the initial setup of your TV and Alexa, you need to make sure both devices are on the same Wi-Fi network.

    MORE: Best Products That Work With Amazon Alexa

    If you haven’t already, you also need to set up your TV as a thing (smart device) in the SmartThings app. To do this, simply log into your Samsung account on the TV.

    Prepare applications.

    You will also need to prepare your phone to coordinate the two devices. If you haven’t already, download the Samsung SmartThings app (available for iOS and Android) and the Amazon Alexa app (also available for iOS or Android).

    And if you don’t know how to use the Amazon Voice Assistant app, check out our guides on using Alexa on your Android phone or using Alexa on your iPhone.

    Make sure you sign in to both apps with the same account information you used for your TV’s Samsung account and your Echo’s Amazon account.

    Discover your TV in the SmartThings app.

    First, you need to detect your Samsung TV in the Samsung SmartThings app, which allows it to be treated as a basic connected smart device when connected to an Alexa speaker.

    To do this, go to the “Devices” menu, which is located in the bottom menu of the application.

    On the Devices page, select the Add Device option. When the TV is on, your device should be easy to find in the list.

    Once you’ve found your device and connected your phone to your TV, select Samsung Smart TV and use the toggle button next to its name to turn it on as a smart device.

    Discover your smart speaker in the Alexa app.

    Second, you need to make sure your Amazon Echo, Echo Dot, or other Amazon device has been detected in the Amazon Alexa app. If this is not the case, or if the device is configured through someone else’s phone, you need to do the following. (If this does not apply to you, proceed to the next step.)

    In the app, select the “Devices” button from the menu at the bottom of the home screen.

    If you see Echo (or a similar Alexa device) in this menu, you’re done. If not, open the All Devices menu item and find your Alexa device in the list of available connected devices.

    Connect apps.

    In the Amazon Alexa app, enable the Samsung SmartThings skill and sign in to your Samsung account to link accounts.

    Select your TV in the Alexa app.

    After you have enabled the Samsung SmartThings skill, which should automatically connect Alexa to your TV, you can use Alexa to turn your TV on and off with your voice. Congratulations, you just connected your Samsung Smart TV to Alexa.!

    For more Alexa-related tips, tricks, and how-tos, check out our complete guide to Alexa.

    The receiver automatically turns off

    The timer function is activated. Check the timer menu settings.

    The transition to digital TV broadcasting is gradually coming to its logical conclusion, the number of analogue repeaters has significantly decreased. Accordingly, it’s time to figure out how to connect a digital set-top box to a TV. To view TV broadcasts in digital format, you need a suitable antenna and DVB-T2 set-top box.

    When tuning the receiver, channels were not found or the message “No signal” is displayed

    Antenna not connected or faulty, oriented in the wrong direction. Main antenna amplifier is not powered.

    Outdoor antenna

    • It is best to buy an antenna without an additional amplifier. It is much more resistant to interference.
    • We use a directional antenna, if there are no significant obstacles, it amplifies the signal.
    • A wide-angle antenna is the best option in difficult signal reception conditions. Its design provides greater coverage.
    • In the most difficult situations, an antenna is required, additionally equipped with a preamplifier.

    How to choose the right antenna

    We will consider how to connect a digital television set-top box to a TV a little later. The first step is to choose a good antenna that will provide a strong signal. It is of two types. indoor and outdoor. The final choice depends on the distance of the TV tower. If the distance does not exceed 15 km, then the indoor model is suitable, if more, the outdoor model.

    We connect the receiver to a new TV

    Now let’s take a closer look at how to set up a digital set-top box to a Samsung TV with Smart TV (this setting will work with other TV models with Smart TV technology as well). The algorithm of actions is as follows:

    • all work must be carried out with the TV off, it will be possible to start it only after everything is completed.
    • using a cable, we connect the antenna to the receiver using the appropriate input;
    • using a cable with HDMI connectors, we connect the receiver to the TV;
    • we connect the power;
    • an assistant will appear on the TV screen to help you make all the settings correctly.

    You will immediately need to choose a convenient language, country and image format. After that, you can start searching for available channels.

    Search for available channels

    We have already decided how to set up a digital television set-top box for a TV, now we are starting to search for all available channels. The most accessible method is to enable autoscanning. We act as follows:

    • go to the receiver menu using the appropriate key on the remote control;
    • select the section “channel search”;
    • in the menu that opens, select autosearch and launch it;
    • the procedure takes a few minutes, after which we save the result.

    If the found number of channels corresponds to the declared one, the setting is considered to be completely completed. In a situation where certain broadcasts are missing, it is better to try to search for them manually, be sure to check the position of the antenna.

    If, after all the manipulations, certain channels are still missing, and the connection is correct, then we restore the basic settings on the set-top box. Next, run the search again.

    Indoor antenna

    Many people are interested in how to connect a DVB-T2 receiver using a home antenna, because it comes with most TVs. The problem is that such receiving devices are distinguished by the minimum amplification parameters, therefore, they are additionally equipped with all kinds of amplifiers. But they do not solve the problem, any fluctuations and interference are immediately displayed on the image quality.

    READ  How to Transfer Contacts from Xiaomi to Samsung

    Digital set-top box standard equipment

    Consider what is included in the standard set for the receiver, this information can be useful when connecting it to a television receiver.

    Digital set-top box standard equipment

    Let’s list what is shown in the figure:

    • A. user manual, we recommend that you carefully read this manual in order to get a complete picture of all the functionality of the device and its connection to TV and antenna.
    • B. “Tulip” (RCA) cable with characteristic connectors, allows you to connect the set-top box to almost all modern TV receiver models.
    • C. a device for decrypting and converting a digital signal into an analog (receiver).
    • D. packing box.
    • E. remote control for the device.
    • F. batteries for the remote control.
    • G. power adapter for connecting the device to a household power supply.
    • H. warranty service coupon.

    The basic equipment may slightly differ from that shown in the photo (for example, “Tulip” is replaced by an HDMI cable).

    Connecting to an old TV

    The signal converter can work even with old models of television receivers when connected to the antenna output (1 in Fig. 3). To do this, you need a piece of antenna wire of the appropriate length and two antenna plugs. In order not to bother with soldering, you can take special F-connectors, the procedure for installing them on the cable is shown in Figure 8.

    How to Set Up your Samsung TV and Set Top Box

    Mounting on an F-connector cable

    • We remove the insulation from the antenna cable, carefully so as not to damage the braid (it is enough to clean 15 mm).
    • Bend the braid as shown in the picture.
    • Carefully remove the insulation from the central core.
    • You need to strip 10 mm of the center wire.
    • We screw the connector clockwise.
    • We do this until the central core protrudes 2 mm from the connector.

    Using the manufactured cable, we connect the antenna input of the TV to the corresponding output of the set-top box. In this way, you can connect any TV, be it Horizon 101 or the legendary KVN.

    What do you need to connect “numbers” on an old TV

    To receive digital television, the following set of equipment is required:

    • Old TV. The later the model is released, the easier it is for it to “make friends” with an external tuner.
    • Console. It is she who converts the digital signal into sound and image.
    • Conventional antenna. capable of receiving TV transmission of the DVB-T2 standard. (find out in 3 minutes which one is better to choose).
    • Cables: antenna (with a characteristic impedance of about 75 ohms) and an adapter through which old TVs (such as Goldstar, Vityaz, Rubin, etc.) are connected to the receiver (more on that below).
    • RF modulator. It will be required where not just CRT models are used (the use of CRT does not interfere with the “digital”), but old lamp Soviet designs, whose connection scheme, in principle, does not provide for operation through the “tulip” or the use of other low-frequency inputs.

    Connecting to an old TV

    The signal converter can work even with old models of television receivers when connected to the antenna output (1 in Fig. 3). To do this, you need a piece of antenna wire of the appropriate length and two antenna plugs. In order not to bother with soldering, you can take special F-connectors, the procedure for installing them on the cable is shown in Figure 8.

    Mounting on an F-connector cable

    • We remove the insulation from the antenna cable, carefully so as not to damage the braid (it is enough to clean 15 mm).
    • Bend the braid as shown in the picture.
    • Carefully remove the insulation from the central core.
    • You need to strip 10 mm of the center wire.
    • We screw the connector clockwise.
    • We do this until the central core protrudes 2 mm from the connector.

    Using the manufactured cable, we connect the antenna input of the TV to the corresponding output of the set-top box. In this way, you can connect any TV, be it Horizon 101 or the legendary KVN.

    How to properly connect a set-top box to a Samsung TV

    Since the all-Russian transition from analogue to digital broadcasting took place, the owners of old TVs have faced a problem: what to do next? CRT “boxes” obviously do not perceive “digital”. It is required to connect a receiver-attachment, but the methods are not always obvious.

    We will figure out how to properly connect a digital set-top box to an old TV and what needs to be done to avoid pitfalls.

    How to connect 2 TVs to a digital set-top box

    Two television receivers can be connected via the antenna output, for this you need a special adapter from one to two cables (splitter).

    Double splitter

    Since the set-top box is intended only for one device, then two TVs will work synchronously, that is, show the same channel.

    Instead of a conclusion

    Although older TVs do not have an internal digital tuner, they can still be used if a set-top box is connected. There are many connection options, as well as adapters for all types of interface, so you can easily choose the one that is needed in a particular case.

    The state program of a phased transition to the digital TV broadcasting standard DVB T2 is approaching the final stage. a gradual reduction in the number of analog repeaters. This suggests that the time has come to join new technologies and switch to digital. We will tell you about the equipment required to receive a television signal in a new format, as well as how to properly connect a digital set-top box (receiver) to a TV or monitor.

    Via RCA

    The easiest option, in which the old TV will show digital programs, is to connect it through the “tulip”, “bell”, also known as a set of RCA connectors.

    This is the oldest type of connector used. Its basis was developed in the 1940s and is still successfully used in a bunch of different audio and video equipment.

    The connection diagram through the “tulip” is as follows:

    • Turn off the TV and receiver from the sockets.
    • Plug the connectors on the cables into the jacks where they fit. Here you need to look at the marking. Usually, the color marks on the tulip plugs correspond to the connectors where they are to be connected. But there are exceptions. there may be only two connectors, and the colors are different. In this case, be sure to connect yellow (video signal) and white (mono sound). red is negligible.
    • Connect the antenna cable to the set-top box. It is he who serves as a signal source.
    • Turn on the TV, go to the menu and select the AV mode. The specific method depends on the model of the TV receiver (setting the settings on the Orion apparatus is very different from those used for Horizon with a CRT still of the Soviet production).
    • Tune the channels on the digital set-top box. It is important here that the cord is not too long, and the antenna is correctly oriented.
    • Store tuned channels in the STB’s memory.

    Synchronization

    Upon completion, it will display the message “TENET application has been successfully installed.” You need to return to the main menu and re-enter the newly downloaded widget. The application will prompt you to enter a login with a password that is assigned to the device.

    READ  How to Send to Samsung Memory Card

    The bundle can be obtained:

    • in the operation manual;
    • from sellers;
    • at the Samsung service center (phone. 7 (495) 925-00-03).

    Upon completion, confirm the entered data and wait a few seconds. Synchronization with the remote server will be established, followed by the following changes:

    • the exact time will be set, a forecast of the pagoda, exchange rates and other information will be issued;
    • there will be news reports about the developer and his products.

    Synchronization will check your device for available updates.

    To watch Internet channels on Smart-TV, you need to install an IPTV player, which can be downloaded from the Samsung Apps service.

    There are two ways to organize interactive television:

    • Connect the “Home TV” service for Smart-TV from an Internet provider. The operator will provide a list of popular high-definition channels at a rate for a small fee.
    • Use free channels. Links to view and download can be found on the Internet. The playlists are completely free, but most channels do not broadcast in Full-HD quality. They are also created with the expectation of extras and contain hundreds of channels, among which only a few dozen will be interesting.

    For IPTV, a high data transfer rate is required because Internet broadcasts are streamed from all channels included in the playlist. Recommended internet speed from 30 Kb / s.

    Setting up and connecting Smart TV on a Samsung TV

    The development of television has led to increased opportunities for users. Today, technologies allow you to watch high-definition broadcasts, as well as use other multimedia functions. The most popular are Samsung TVs, which today are considered the most advanced. However, this technique requires complex customization that not everyone can do. The information below will help you understand how to connect and set up Samsung Smart-TV on your TV.

    Registering a device

    If the menu is not in Russian, you need to go to the system settings and change it, and also select the region (Russia or Eastern Europe).

    In the first step, it is important to register your Samsung device and activate synchronization of the device with a remote server.

    • At first. this will confirm the use of the licensed equipment and will be supported remotely.
    • Secondly. the user will receive updates for the software and individual widgets.
    • Thirdly. without user registration, smart TV functions will become unavailable.

    Functions and characteristics

    Like conventional TVs, Samsung advanced models provide the user with a modern and high-quality TV.

    Among the mandatory criteria for these devices:

    • support and playback of video content of all formats (mpeg-4, acc, m3u, avi, etc.);
    • high pixel screen resolution (from 1080p);
    • presence of ports for high-bandwidth cables.

    With a smart TV, the user can enjoy high definition digital TV with the same comfort as using a computer or digital set-top box.

    Each model provides a separate set of features that the user can expand at any time by downloading new widgets from the Samsung Apps developer service.

    What is important to know

    Literally the term Smart means “smart”. It is expected that such a TV should provide more options than a conventional digital TV model. In most cases, such devices provide Internet access and support for a large number of multimedia formats.

    There are also smart receivers, but Smart-TV on TV and set-top box, different topics. If the TV is a full-fledged device, then the receiver only improves its capabilities and opens access to “smart” options on older models.

    Today, smart TVs are produced by many developers, and in addition to it, there is a wide range of applications and services. For this reason, the capabilities of devices with Smart-TV support differ from different manufacturers.

    Connection and configuration

    Setting up digital TV for Smart-TV is performed in the same way as on a regular TV or receiver.

    Models with smart TV support when tuning digital channels also solve the problem of storing already present channels. They have a system setting that allows you to select a radiation source (antenna, satellite, cable).

    For example, if you manually tune digital TV channels and select a cable as the signal source, the search does not occur in other bands and the programs of terrestrial and satellite TV are saved.

    But the setting of digital channels on the TV is not enough to take full advantage of the Smart TV function and you need to connect to the Internet.

    There are four methods available for Samsung models:

    • Wired Internet. The connection is made using an RJ45 Ethernet network cable to the LAN connector. To connect, you need a home Internet.
    • Wi-Fi. Wireless connection with data transfer rates up to 30 Kb / s. Not all TVs with Smart-TV function have a built-in Wi-Fi module. If it is absent, you need to purchase a router with a USB-input connection.
    • WPS. This technology allows you to connect to a Wi-Fi network using a router without entering additional settings. It is only available when using a router and must be supported by it.
    • PlugAccess. Samsung’s unique internet connection technology, which is only supported by devices from this manufacturer.

    After selecting the connection method, the connection is established. You need to go to the settings menu by pressing the corresponding button on the TV or remote control. After opening the Smart-TV interface, you need to enter the settings and select the “Connection” item there.

    Establishing a connection

    The menu that opens will display a list of available networks.

    The further step-by-step connection establishment depends on the connection method:

    • Direct connection. An available connection is selected and the password provided by the network operator is entered, after which the entered data are confirmed with the “OK” button. After a few seconds, the connection will be established.
    • Using a router. In this case, the data of the router (IP address, port, DNS addresses and password) are registered, which can be found in the operating instructions or obtained from the operator (if leased).
    • PlugAccess. It is required to enter the settings item “Connection”. After that, insert the USB drive into the router, wait for the indicator on the device to change, pull out the USB flash drive and insert it into the TV with Smart-TV. After a few seconds, the connection will be established automatically.

    After successful connection, you can start setting up Smart-TV on your Samsung TV.

    User registration

    To perform this procedure, you need to turn on the Smart Hub, to enter which there is a corresponding button (for old Samsung F-series TVs and other models of 2011-2014, there is a green button on the remote control). A menu will immediately open with an offer to register.

    You need to follow these steps:

    • select the item “Create an account”;
    • accept the user agreement (privacy policy);
    • enter the desired username and password;
    • tick the box “Receive E-Mail on Samsung Smart TV.

    After registration, you will be prompted to pass authorization or log in under the “Guest” (Ghost) status. You need to select a user and log into your account. Hidden Smart-TV settings are not available for guests

    BYRGPUB.COM 2021