Table of Contents

connect, rearview, mirror

15th place. AXPER Mirror Simple: Features and Price

A typeRearview mirror with screen;
Resolution1920 x 1080 @ 30 fps;
functionshock sensor (G-sensor), motion detector in the frame;
viewing angle120 °
The matrixCMOS 1/4 “5MP;
Battery80 mAh;
screen2.8 inches;

AXPER Mirror Simple: Pros and Cons

14th place. Vizant 250 Assist: Features and Price

A typeRearview mirror with screen;
Resolution1920 x 1080 @ 30 fps, 1920 x 1080 @ 30 fps;
functionsshock sensor (G-sensor), motion detector in the frame;
viewing angle140 ° diagonal, 110 ° wide
The matrixCMOS 1/4 “5 MP;
Battery500 mAh;
screen9.66 inches;

Vizant 250 Assist: Pros and Cons

13th place. CARCAM Z6: Features and price

A typeRearview mirror with screen;
Resolution1920 × 1080 @ 30 fps, 1920 × 1080 @ 30 fps;
functionsshock sensor (G-sensor), motion detector in the frame;
viewing angle140 ° diagonal;
Battery300 mAh;
screen4.3 inches;

CARCAM Z6: Pros and Cons

12th place. SilverStone F1 NTK-351 Duo: Features and Price

A typeRearview mirror with screen;
Resolution1280 × 720;
functionshock sensor (G-sensor), motion detector in the frame;
viewing angle140 ° diagonal;
screen3 inches;

Silverstone F1 NTK-351 Duo: Pros and Cons

11th place. Playme VEGA: Features and price

A typeRearview mirror with screen;
Resolution1920 x 1080 @ 30 fps, 1920 x 1080 @ 30 fps;
functionsshock sensor (G-sensor), GPS, motion detector in the frame;
viewing angle146 ° diagonal;
screen5 inches;

Playme VEGA: Pros and Cons

10th place. Eplutus D02: Features and Price

A typeRearview mirror with screen;
Resolution1920 x 1080 @ 30 fps;
functionsshock sensor (G-sensor), motion detector in the frame;
viewing angle140 °
The matrixCMOS 1/4 “5 MP;
Battery450 mAh;
screen4.3 inches;
cameras2 pcs;

Eplutus D02: Advantages and Disadvantages

9th place. Dunobil Spiegel Duo: Features and Price

A typeRearview mirror with screen;
Resolution1920 x 1080 @ 30 fps;
functionshock sensor (G-sensor), motion detector in the frame;
viewing angle120 °
The matrixCMOS 1/4 “5 MP;
Battery300 mAh;
screen4.3 inches;
cameras2 pcs;

Dunobil Spiegel Duo: Advantages and Disadvantages

8th place. VIPER C3-351 Duo: Features and price

A typeRearview mirror with screen;
Resolution1920 x 1080 @ 30 fps;
functionshock sensor (G-sensor), motion detector in the frame;
viewing angle170 °
screen4.3 inches;
cameras2 pcs;

VIPER C3-351 Duo: Advantages and Disadvantages

7th place. DIGMA FreeDrive 303 MIRROR DUAL: Features and Price

A typeRearview mirror with screen;
Resolution1920 x 1080 @ 26 fps;
functionsshock sensor (G-sensor), motion detector in the frame;
viewing angle120 °
The matrix1.3 megapixels;
Battery250 mAh;
screen4.3 inches;
cameras2 pcs;

DIGMA FreeDrive 303 MIRROR DUAL: Advantages and Disadvantages

6th place. Xiaomi Smart Rearview Mirror: Features and Price

A typeRearview mirror with screen;
Resolution1920 x 1080 @ 30 fps;
functionsshock sensor (G-sensor), GPS, GLONASS;
viewing angle160 °
The matrixCMOS 1/4 “5 MP;
Battery370 mAh;
screen8.88 inches;
cameras2 pcs;

Xiaomi Smart Rearview Mirror: Advantages and Disadvantages

5th place. Parkprofi Yi 3z: Features and Price

A typeRearview mirror with screen and additional camera
Resolution1920х1080 at 30 fps
viewing angle120⁰
display4.3 “
functionsShock sensor, motion sensor, loop recording
cameras2 pcs.
Priceabout 2500 rubles.

Parkprofi Yi 3z advantages and disadvantages

4th place. Artway AV.604 Super HD: Features and Price

A typeRearview mirror with screen and second camera;
Resolution2304 x 1296 at 30 fps;

Artway AV-604 Super HD: Advantages and Disadvantages

3rd place. Slimtec Dual M7: Features and Price

A typeRearview mirror with screen;
Resolution1920 × 1080;
functionshock sensor (G-sensor), motion detector in the frame;
viewing angle150 °
Battery800 mAh;
screen7 inches;
cameras2 pcs;

Slimtec Dual M7: Advantages and Disadvantages

2nd place. Roadgid Blick WI-FI: Features and Price

A typeRearview mirror with screen and video streaming;
Resolution1920 x 1080 @ 30 fps;
functionshock sensor (G-sensor), motion detector in the frame;
viewing angle170 °
The matrixSony Starvis IMX307;
Battery350 mA / h;
screen10 inches;
cameras2 pcs;

Roadgid Blick: Advantages and Disadvantages

1 place. Slimtec Dual M9: Features and Price

A typeRearview mirror with screen;
ResolutionFull HD 1080P HD 720P
functionsshock sensor (G-sensor), motion detector in the frame;
viewing angle170 °
Battery800 mAh;
screen9.66 inches;
cameras2 pcs;

Slimtec Dual M9: Advantages and Disadvantages

How to connect two rear view cameras

The last thing a driver wants to do is damage the car while parking on a busy street. Especially if it’s someone else’s car.

And the truth is, no matter how experienced the driver is, there is a subtle little thing that will cause trouble. In such a situation, a rear view camera comes in handy. It significantly improves visibility and avoids unpleasant excesses.

Today, many cars are equipped with this useful gadget, especially the premium segment. But early models lacked such a function, which means. there is a reason to pick up a tool.

How to connect a rear view camera to a Chinese radio tape recorder today will be discussed.

How to choose a system

The automotive electronics market abounds in a variety of connectivity kits. This is especially true for products from China.

Indeed, for some owners, the quality of the transmitted picture or the backlighting in the dark is not at all critical. So not worth paying money for unused features.

For a better understanding of the devices presented, you need to understand the basic parameters. These include:

  • Video resolution. The higher this parameter, the better the video quality is on the screen. High-resolution cameras provide detailed images of the smallest objects behind the car.
  • Matrix sensitivity. Sometimes this parameter is indicated by the “ISO” symbol. Cheap models are not equipped with sensitive matrices, this directly affects the image quality in the dark. The picture is fuzzy, it floats while moving.
  • Shooting coverage. The standard viewing angle range is 120-180 degrees. A high value helps to make the video panoramic, a lot of space will fit into the frame. But there is an insidious moment: at such angles, the real dimensions of objects are distorted, which can deceive an inexperienced driver. Therefore, the optimal solution should be sought between These values.
  • Camera body and installation type. Waterproof devices can be safely installed outside the car, they are not afraid of water and dirt. But they will always be available to thieves. Indoor cameras are installed in the luggage compartment. Space coverage will decrease, but the device will always be dry and protected from prying hands.
  • Connection type. Standard. wired connection. A cable is laid from the monitor or radio to the back of the car. unusual is the wireless connection. The driver does not need to remove the trim and hide the wiring. But this method requires additional accessories. transmitters.
  • Rear cameras with backlight function. With such devices, you can easily navigate in the dark. Illumination is carried out by infrared diodes or an additional lamp. This function is useful for those cars in which the taillights are small and give a low light. Do I need this type of cameras. the owner decides individually.

You must also pay attention to the method of displaying the image. It can be a separate monitor or a 2din radio with a built-in screen. If the quality of the latter suits, it makes sense to install a second monitor.

How to connect a camera to a radio tape recorder with your own hands

Initially, you need to choose an installation location. There is enough space in the back of the car, but when you take into account the coverage of the broadcast picture, the choice decreases.

It is worth considering the location of the camera eye. He must have a view over the entire shooting angle and NOT be obstructed by other body elements.

There are two installation options: under the license plate and under the rear window. Here it is worth considering the type of car body. For station wagons, due to the lack of a long trunk, both methods are suitable. For sedans, the best place. in the license plate compartment.

Let’s move on to the connection. Before starting work, you must prepare the tool:

  • The camera kit itself with wires;
  • Screwdriver;
  • Keys set;
  • Pliers;
  • Knife;
  • Plastic ties;
  • Electrical tape or heat shrink tubing.

Sometimes you may need to drill multiple holes to mount the rear camera. In this case, you should stock up on drills and a drill. Some car models have a prepared place for the camera, for which it is enough to pull out the factory cap.

Prepare the vehicle interior for wiring. Pull the upholstery gently. Choose a location where the cable will not be deformed by the feet of passengers and avoid sharp bends in the cable. It will be reliable to strengthen the wire on the standard highway cars. Strengthen the main line with plastic ties.

Let’s move on to connecting a rear view camera to a Chinese 2din radio tape recorder. To get to the ISO connections and the rear of the audio system, you need to carefully open the front panel (or several, depending on the car) of the torpedo, and Unscrew the fastening screws. The head unit can be detached.

Advice: for the safety of the electrical circuits of the machine, all connections should be made with the battery disconnected. This eliminates the risk of accidental short circuit to ground.

Diagram of connecting the camera cable connectors to the car radio

When the preparatory work is completed, the cables are laid, you can proceed to connecting all the system components.

Let’s take a closer look at the diagram:

A standard connection cable consists of two parts:

  • Yellow. signal;
  • Red. food.

Please note that voltage wire colors may vary on different models.

READ  Mirror Recorder Not Working Rearview Camera

The connection of the video signal is carried out through connectors of the “tulip” type.

The standard method for powering and activating the camera is through the reversing lights. The principle of operation is as follows:

  • The red wire connects to the lights, the black one. per vehicle weight.
  • The signal cord, through the trunk in the passenger compartment, is connected to the radio tape recorder through the Video In.
  • When you turn on the reverse, a voltage appears on the supply conducts the camera, which activates it.
  • The radio tape recorder detects the signal on the input channel and switches to the image broadcast mode.

Very often, the radio is connected via the ISO connector. In this case, you should familiarize yourself with the connection pins and find the video input.

The second connection method allows you to activate the surveillance system regardless of the reverse. For this, 12V is supplied to 2 wires. Red and blue. The first is connected to the ignition switch, to the key1 position. ACC. The second is supplied to the reversing lamps.

With this method, the system will operate in two modes:

  • When shifting into reverse gear;
  • In key positions key1 and key2. Ignition, which corresponds to the included vehicle electrical system and ignition.

Some models of radio tape recorders require manual activation of the shooting mode in the “settings” of the device. After activation, you should check the work in different key positions, especially in key2.

The next step. adjust the radio itself, namely focus, sharpness and light sensitivity. Different systems offer a different set of settings, so configurations are individual.

Tip: It is important to observe strict correctness when connecting the wires. In order not to be mistaken, it is recommended to assemble the system on a table and configure it. When connecting the supply components to the vehicle network, protect them with fuses.

Connecting a car reversing camera to a laptop

To be able to view the picture on a laptop, you need a special TV tuner. It can be used to match an analog signal with a computer.

The connection principle remains unchanged. The supply wires are supplied with a voltage of 12V, and the tulip is a video signal. to the tuner. Shooting is controlled through software.

Ways to connect two Chinese cameras to the radio tape recorder

On the market Models for dual-zone monitoring of the machine space are presented. in the front and in the back. This solution allows you to register Potential emergencies on the road, and Fix the state of the car in the absence of the owner.

Connection and configuration is carried out in the following order:

  • The on-board network of the car is de-energized;
  • The front camera is installed on the rear-view mirror holder;
  • Mount the back;
  • For aesthetics, the connecting wires are led to the main module under the passenger compartment trim;
  • If the head unit has two Video In. Connect signal wires to them. In the case when the kit has its own recorder. choose the place of its installation, connect to the network and cameras;
  • We check the connections according to the installation diagram, turn on the battery;
  • Configuring the parameters of the cameras.

It remains only to test the system in motion and, if necessary, make corrections.

Sometimes it happens that one of the cameras does not provide adequate coverage of the space in front of it. Exit. purchase an overlay “Fish Eye”. It acts as a wide-angle lens and widens the angle of view.

How to connect a mirror with a rear view camera

The way to connect such a mirror is no different. The connection diagram looks like:

Often, sets of mirrors with cameras can take power from the cigarette lighter, through their own connector. The owner can choose which voltage supply method suits him best.

expensive mirrors support both sides of the vehicle. The front camera is already integrated into the product body and does not require connection.

Connecting a Chinese rear view camera to a Japanese radio

Lovers of high-quality audio systems Japanese equipment. But they have their own nuances when connecting video cameras.

Consider an example on a Pioneer 2din radio tape recorder. Installation has a similar procedure:

  • The camera is powered from the reversing light.
  • The signal cable is connected to the Video In connector. Usually, in this model, a brown tulip responds with theft of the video.
  • We check in the settings the inclusion of the camera and its operation.

The system works, but automatically, when driving backwards, it will not turn on. It is enough to connect the purple wire of the head unit to the rear lights, where the camera is. The problem will be fixed when the reverse gear is engaged. The radio tape recorder will understand that you need to activate the shooting mode.

The rest of the installation points of the device remain the same.

Rear-facing or front-facing cameras have proven themselves to be the best among car enthusiasts. With their appearance on board the car, it becomes easier to navigate in confined spaces. Their correct installation requires some knowledge from the owner. But with the advice given, any driver can do it.

In this article, we will try to cover as much as possible all existing types of rear-view cameras, how to install and connect them, as well as give instructions on what you need to pay attention to when installing the camera. We will try to cover all the possible nuances that will help you install the rear view camera yourself without contacting the service.

Rear-view cameras are divided into:

Regardless of how you install the camera, the connection is approximately the same in all cases. So, first you need to choose an installation location. all rear-view cameras are usually located in the center of the longitudinal axis of the car, but if we are talking about a standard camera that is installed in the license plate illumination then the installation site will be slightly shifted to the center, this fact must be taken into account later when maneuvering. It is better to install the camera in the right illumination of the license plate, while parking to the right curb, the view will be slightly larger than when installing the camera in the left illumination of the license plate.

So, before installing the camera, you must disconnect the terminals from the battery.

Next, you need to determine the place to enter the wiring into the luggage compartment to connect the wires, usually for this they use the holes in which the wiring for the license plate light is wound. If the camera is installed in the bumper, then the wiring must be pulled from the back of the bumper to the headlight, and then insert the wires into the holes under the headlight. First, it is better to try to stretch all the wires and reinstall all the elements (camera, room lighting, headlight) without connecting the wiring. After when it is clearly clear how the wires will pass and nothing interferes with them, you can connect.

Usually the camera has two connectors. yellow V1 for connecting the video cable and red P1 for connecting power (connectors may differ depending on the type of camera).

In addition, in standard rear-view cameras, LED backlighting can be provided in this case, it is necessary to connect the P2 connector to the car wiring to which the standard backlight was connected (red wire 12V, black. Ground).

Next, you need to connect the camera to the reversing lamp (with this type of connection, the camera will automatically turn on when you turn on the reverse gear). The connection is usually made using an additional wire, which comes with the camera, the red wire is connected to the anode of the reversing lamp (12 V), the black wire is connected to the ground. The ground should be connected not just to the car body, but it is necessary to ensure good contact, while the problems of the camera will be excluded.

After that, you need to stretch the video signal wire to the monitor (in the case of using the wireless transmitter kit, connect the video signal to the transmitter).

Some monitors and OEM head units have a connector for inputting a signal to switch to the rear view camera mode; especially for this, there are small red wires on the video signal extension cable. One end of this red wire must be connected to 12 reversing lamps, the second to the monitor input (monitor in the mirror, ShGU, head unit, etc.) for the signal to switch the monitor to the rear view camera mode.

Connection diagram for rear view camera to monitor.

P1. rear view camera power connector.

P2. Wire to connect power to the reversing camera, one end connects to the camera the other to the reversing lamp.

V1. Rear View Camera Video Connector.

V2-V3. A video signal extension cable (laid through the car interior), instead of this extension cable, you can use a wireless receiver. transmitter, in this case you DO NOT have to disassemble the elephant and pull the wiring.

P3. wire for connecting the signal to automatically switch the monitor to the rear view camera mode (one end to the 12 reversing lamp, the other to a special monitor input or SHGU)

You can choose a camera specifically for your car here:

Thanks to a device such as a rear view camera (RCV), the driver will be able to know how to park and what obstacles might interfere with it. You will not surprise anyone with such a device today, recently more and more motorists are equipping KZV cars. From this material you can find out how the rear view camera is connected to the car radio and what you need to know about the choice of devices.

Criterias of choice

If you decide to purchase a rear view camera, you may be faced with a wide range of devices on the market. Many brands are engaged in the production of KZV, as a result, the products differ not only in terms of manufacturers and cost, but also in functionality and configuration. In accordance with preferences and capabilities, you can purchase a complete set of device (camera with display), or connect the system to a Pioneer radio or other.

General criteria for choosing a device:

  • A type. KZV can be both wired and wireless. In the latter case, it is necessary to organize a Wi-Fi access point in the car.
  • Viewing angle. the parameter largely determines the quality of the image coverage. Optimally choose devices with a coverage angle of 120 to 170 degrees.
  • Image quality, a lot depends on it.
  • Device body. It is important that he be strong.

How to determine the location of the camera?

Before connecting the camera, you need to choose a place for mounting the device. KZV can be installed in the trunk lid, license plate frame or in the rear bumper. Such an installation place will not spoil the external design of the vehicle, it is. the best option in terms of height. the required image will be displayed on the monitor.

READ  How To Connect An Analog Video Camera To A Computer

Depending on the type, KZV can be installed instead of the license plate illumination, while the device is equipped with a backlight option. But its quality is much worse. The main criterion that you need to rely on when choosing a place for installing the system. how much the camera will get dirty. On many vehicles, due to aerodynamic features, the rear of the bumper can become covered with mud in bad weather.

Installation from A to Z

How should the KZV be installed and connected? If you want the radio with a rear view camera to work for a long time, follow the recommendations below. For installation, you will need a circuit that should be included.

Installation process

  • Remember that all electrical work is carried out with a de-energized on-board network. Therefore, it is necessary to disconnect the battery.
  • First, the camera is mounted, in particular. peephole, depending on the design features of the car, a place may be provided for this element. If it is, then it is only necessary to dismantle the cover and install the peephole there. If there is space, then you need to drill a hole in the bumper and fix the peephole in it with silicone or glue.
  • Then the wiring from the device is laid in the luggage compartment, the negative terminal should be connected to the mass of the car, for this you can use a regular bolt. The positive terminal connects to the optics wire that turns on when reverse gear is activated.

Diagram of connecting the camera to the display of the car radio

Connecting to the radio

  • In order for the image to be displayed on the monitor of the car radio when turned on, it is necessary to lay the yellow wire through the passenger compartment and secure it with electrical tape. Make sure that the cable is not bent and that it is NOT affected by moving parts of the body, otherwise it will have to be replaced soon. If the length of the wire is not enough for laying, you can try to increase its size using a similar cable.
  • Then the wire must be connected to the audio system, for this you need to read the instructions for the radio. The connection principle is identical in almost all systems. The end of the yellow wire, the so-called tulip, must be connected to the Video In connector.
  • If you use the wireless version of the camera, the principle of connecting the system will be identical. Instead of one end of the wire, it is necessary to install a special sensor in the Video In connector, which is included in the kit to the KZV. Actually, when these actions are completed, the installation procedure for the KZV can be considered complete. But before assembling the upholstery and preparing the car for operation, it is necessary to diagnose the system’s performance.

Camera check and setup

To make sure that everything was done correctly and that the KZV of the type is working in normal mode, it is necessary to check the operability of the device. To do this, connect the battery, start the car engine and engage reverse gear. At this moment, a picture should appear on the display of the radio. if so, then everything is installed and connected correctly.

If there is no picture or is poorly displayed on the display, do the following:

  • Go to the car radio menu and select “Settings” or “Settings”.
  • Then go to the submenu “Cameras” or “Cameras”, depending on whether the audio system is Russified or not.
  • Then in the existing list you need to find your camera.
  • Using the settings Let’s adjust the focus and other settings of the KZV eye.

After completing these steps, you can customize the system to fit your needs.

Issue price

As for the cost, the majority depends on the manufacturer. KZV can be wired and wireless, a lot also depends on this. The price is assigned not only for the brand and type, but also for the functional features, as well as the quality of the device. On average, the cost of KZV on the market is as follows:

DVR with rear camera connection diagram

1) connection of the DVR. It was required that the power cable was not connected to the cigarette lighter. I wanted a “hidden” connection.

Means “” I took in the driver’s visor backlight. brown “-” took by the eyeglass case.

T.K. The recorder is powered by 5 volts, and the car gives 12V. Therefore, dad dismantled the cigarette lighter from the registrar, rolled in the wires: “” In the center of the cigarette lighter “-” minus. On the sides Then he collected this case and pulled the zip ties over the eyeglass case (photos are not mine)

2) connecting a rear view camera.

T.K. The camera will come soon, I found a wiring diagram for a camera with additional power.

We recommend using the control wire to automatically turn on the rear view camera when you turn on the reverse gear and display the picture from the rear view camera on the screen of the model (navigator, etc.). It is connected to a wire called BACK or Reverse and to the plus of the reverse light.

In cases where there is no control wire, then it can be made from any wire and laid in parallel with the video signal cable! Wiring diagram diagram 1

In cases when you connected the camera, checked, the picture is good, but you have interference with the motor, the screen is ruffled, then in this case you need to use a relay to turn on the rear view camera, below is the electrical diagram. The relay can be used from VAZ, such as windshield wiper relay, cooling fan relay, etc. Scheme2

Whether or not to put a reversing camera, each driver decides for himself. In this article, we will tell you how to connect a rear view camera, and it’s up to you whether you need it or not. Connecting a rear view camera requires some well-known and skills, so not everyone can do it on their own. But if you nevertheless decide that the installation of a regular rear view camera is necessary for you, then use the tips from this article. With a small set of tools and initial skills in working with them, you can easily figure out how to connect a rear view camera.

Side mirrors, and even your head turned 180 ° will not give the desired effect, some little things, and maybe NOT little things, you still may not notice. And then dismantling with the owner of the scratched car may begin, and this can cost you tens of times more than connecting a reversing camera. Further in the article, we will consider which camera you can choose, whether a Chinese manufacturer is right for you, or if you prefer something more solid. We will also discuss whether it is possible to install a rear-view camera with your own hands, and how to properly connect your chosen device.

How to choose a camera

The modern electronics market, and especially China, is overflowing with a variety of cameras, and this makes the choice of the right thing more complicated. In order to make your job easier, decide on the priorities that you care about more. price or quality. Not everyone needs high definition cameras, or cameras that can show even in poor lighting conditions. For some DRIVERS, an inexpensive rear-view camera for the radio is enough.

  • In what resolution the camera writes, the higher the video resolution, the better the recording quality. And high definition of the image is not always needed.
  • The next moment. camera sensitivity to lighting. In cheaper models, recording quality in low light can be very poor. Therefore, if, due to circumstances, you often use the car in the dark, then at this moment it is worth paying attention.
  • If you have already decided before buying where you will put the rear view camera, then you need to Pay attention to the installation method of this particular model.
  • The next moment. this angle of view that captures the camera lens. Usually it is in the range from 120 to 180 degrees. It is better to take something in between These two indicators, so that you have a good rear view, but there was no panorama, because with it the reality is distorted.
  • Selection of the monitor on which the camera will display the image. But if you already have a radio with a screen in your car, then you just need to think about how to connect a rear view camera to the radio.
  • How and where should it be installed

    Later in the article, we will look at how to install a rear view camera. There is more than enough room in the car to install a video camera, but we need the most advantageous position. There must be a good view through the camera peephole, which is NOT limited to any machine parts. Any camera will reach its full potential if it is Installed in the Best Place.

    In our case, such a place is a niche above the rear bumper of the car; the camera should be placed in its upper part above the state number of the car. What does it give. viewing angles, your car radio will only show the road, not parts of your car. But it must be arranged so that it is not strongly recessed, but also does not stick out.

    True, there is a minus here. your camera is accessible to dirt and the wrong hands. If you place it inside the cabin on the rear window, then half of the screen will be occupied by the trunk, the viewing angles will decrease and the image quality due to glass will suffer to some extent. But on the other hand, it will be clean and inaccessible to strangers.

    So you personally have to calculate all the pros and cons of the external and external location of the camera.

    The procedure and diagram for connecting a rear view camera

    And now in more detail about how to install and connect a rear view camera to a Pioneer radio. Why this model, because it is the most common. If we take into account the insecurity of our video camera, and the best view, then its place should still be above the number, outside.

    It should be installed closer to the edge to improve visibility, but not so that it is exposed. The installation of the camera itself is not a big deal. The camera has a bracket required for installation, you only need to drill a couple of holes for the mounting bolts, and one hole for the cable.

    And then the rear-view camera is included in the general electrical network of the car. If you are NOT strong in electricians, then it is better to Contact a car service specialist, but if you have at least basic knowledge, then you can quite figure it out on your own. So, the order of connection is in stages:

    • Any camera has two wires, one for transmitting the video signal from the camera to the monitor, and the other for power. Since the camera itself has short wires, you will need to extend them so that they are enough from the front panel to the end of the trunk (as a rule, an extension cable for the video signal is included in the kit).
    • Where can I get power for the camcorder? Usually the camera is connected to the rear light. Therefore, immediately after turning on the reverse, the rear view camera is also turned on.
    • All wires stretched through the cabin and in the trunk must be secured and hidden. This will help avoid unexpected network interruptions while driving.
    • If you use a monitor instead of a radio, you will need to find a power source for it. If you have a Pioneer multimedia recorder, this issue is solved automatically.
    READ  How To Check The Rear View Camera On TV

    Connecting a reversing camera to a Pioneer radio

    Now we will specifically talk about how to configure and connect the reversing camera to the Pioneer radio tape recorder. There are small nuances here that mislead everyone. Connect the camera to the reversing light, all power is on the camera, then the wire through which the video signal will go. In Pioneer, this is a brown tulip, not to be confused with yellow. We go into the settings, find the section in the rear view camera menu, put the item on, and switch the polarity to battery mode.

    Our camera works, you can check it, go to the main menu and select the camera icon, but it will NOT turn on automatically. This can be fixed by connecting the purple wire to the taillights (where the camera is). In total, when the reverse gear is turned on, the lamp lights up to the camera, power is supplied, and the radio tape recorder understands that it is necessary to switch to reverse gear. The whole connection diagram of a rear-view camera is quite simple, and therefore most drivers often cope with its installation on their own. In cars equipped with automatic transmission, accidental activation of the rear view camera may occur.

    To eliminate this problem, you need to install an additional camera turn-on delay sensor. In each car model, the installation of the camera may be different, but in the details, the principles of connection are similar. The process of connecting to video cameras that transmit a signal by radio is more complicated, but they have the advantage that several such cameras can be connected. There are more and more cars on the streets of the city, so there is a rear view camera. this is already a necessity. It will not only help you park correctly, but will also preserve evidence of your innocence in the event of a collision.

    Often, a reversing camera is installed after purchasing a new radio tape recorder, in this case we have an article “how to connect a radio tape recorder” in which you will learn about adapters, adapter frames and much more.

    Mirror with rear view camera. it is a device that allows you to more effectively monitor the road behind the vehicle when reversing to improve safety. It also serves to display useful information. This is achieved by the presence of a built-in display.

    Functions and characteristics

    The angle of view of the view camera with the monitor in the mirror characterizes how well objects located to the left and right of the vehicle will be viewed. There are 2 options for installing a car mirror with a camera:

    • Instead of the standard interior rear-view mirror.
    • As an overlay on a standard mirror using clips.

    Many mirrors with a camera have parking sensors, which makes it easier to park a car in tight spaces. A special radar, which is installed behind the car and connects to the device via wires or Bluetooth, determines the distance to the nearest obstacle. Lines will appear on the screen to indicate the dimensions. If the device has a speaker, beeps will sound. Parktronic function is useful for a novice driver to facilitate maneuvering.

    The size of the monitor built into the device can range from 3 to 6 inches. The larger the screen size, the smaller the viewing area of ​​the mirror. expensive models can be equipped with additional devices and functions, such as a navigator, at times, a video recorder. If the accessory has a built-in radar detector, the driver will be able to slow down in advance before approaching the controls.

    Criterias of choice

    Please pay attention to the input and output interfaces before purchasing. Most often, a rear view camera is connected using cables with RCA connectors and a power socket. If the accessory is rated for 5V, then make sure the mirror has a 4-pin jack socket. The rear view camera must be compatible with the parameters of this device.

    The higher the resolution of the picture received from the camera, the more clear and distinguishable small objects will be. When choosing a mirror by display size, you should focus on convenience. For example, a device with a six-inch screen is suitable for viewing videos and photos, but the view behind the car can be difficult due to the reduction in the useful mirror area.

    Rating of the best models

    These view camera mirrors are in good demand and have all the functions you need. In some models, small monitors are installed under the mirror sheet. Some mirrors are full-fledged DVRs with rearview camera input.

    Trendvision MR710GP

    This device is a mirror image DVR with camera and monitor. The accessory has a high-quality matrix that allows you to shoot videos with Full HD and Super HD resolution. The image refresh rate is 60 frames per second. Another advantage is the wide viewing angle. 147º. The built-in memory is 128 GB. There are 2 slots for SD and MicroSD memory cards. A video input is provided for connecting a rear view camera.

    The built-in battery provides autonomous operation of the device for 20 minutes. The constant power supply of this mirror with a monitor is carried out from the on-board network with a voltage of 12 or 24 V. The device has a built-in 4.7-inch display located in the middle of the mirror. The built-in GPS informant warns of the appearance of traffic police posts on the way. No navigator function.

    Autoexpert DV-525

    This mirror with a camera and a monitor for a car can be installed instead of the standard one. Dual video input allows you to connect not only the rear but also the front camera. The monitor with high-quality color reproduction and high contrast is located on the left. Another advantage of the Autoexpert DV 525 device is secure fixation thanks to spring fasteners with adjustable height. Limits of change. from 55 to 78 mm. The only drawback. overcharge.

    Dunobil Spiegel DUO

    This device is a panoramic mirror video recorder, which compares favorably with the presence of a rear-view camera with a standard VGA resolution. A wiring harness terminated with a 4-pin connector is provided for connection. The device has various useful functions such as a motion sensor and a G-sensor. Screen diagonal. 4.3 “. A 250 mAh battery is provided for short battery life.

    Interpower Silverstone f1 Interpower HD-5

    This camera mirror has a 5-inch display with a resolution of 800 x 480 pixels. The device is powered from the vehicle’s on-board network. The display shows a high quality image, which may not be bright enough in summer. Another disadvantage of this model. short wires for connection, which may cause difficulties during installation. The mirror has a good viewing angle, which allows it to be used for its intended purpose.

    SHO Me M43

    This device with a monitor for a camera view is widespread due to its low cost. It has a 4.3-inch low-resolution display. 480 by 272 pixels.

    The auto mirror of this model has a small height, which makes it difficult to use it for its intended purpose.

    Another drawback is the low contrast and color saturation of the display. But there is also an advantage. this is the presence of 2 video inputs.

    How to install

    Installation of a view camera with a mirror. the process is simple. The easiest way is to install a camera mounted in the license plate frame. Installing a camera instead of a canopy will require skills and tools. You will also need to decide on the installation site so that a good view is provided and fogging and road dirt are not allowed.

    Mirror installation

    If a universal spring latch is used, then squeeze one of them as hard as possible to install on top of a standard mirror. Then the accessory is carefully put on and the latch is smoothly released. The other latch is locked in the same way. When installed instead of a standard mirror, the latter is removed and the new device is installed using the mount included in the delivery set.

    Camera mounting

    To install the camera on a view with a license plate frame, remove the latter and screw on the device. The wires from the accessory can be brought into the body through the trunk by drilling a hole next to the license plate. After routing the cable from the camera, it must be sealed. When the frame is installed, the license plate is screwed into place.

    If you plan to install instead of one of the shades, you should purchase a special kit suitable for the vehicle. You can also put the camera inside the regular case. To do this, disassemble it, cut through the front and back covers for the accessory and insert it. After that, the body is assembled and sealed with silicone sealant.

    How to connect correctly

    The camera connection diagram for a car depends on the availability of the required interfaces. When connecting the camera via a 4-pin jack, make sure the pinout is correct. The first contact of the connector is connected to the reverse switches so that when its contacts are closed, the mirror display turns on. The second contact supplies the analog video signal from the rear view camera, and the third contact supplies 5 V. The fourth contact. it is mass. It is necessary to check both the diameter of the plug and the socket so that they fit together.

    The plug fits into the socket on the mirror monitor. Then the video signal is connected by inserting the yellow plug from the camera into the socket on the adapter. If the mirror with the monitor has an output for powering the camera, then its corresponding connector is inserted into this socket. Otherwise, power is supplied separately from the reversing light button. This is necessary so that the camera is NOT constantly energized, but only while reversing.

    The wiring from the camera is routed to the floor or ceiling. It should be located as far as possible from the antenna cable and car radio wiring to avoid interference. The constant power supply of the mirror can be taken from the lighting shade. To do this, it is removed, and with the help of a tester, the contact of the lamp switch which is under voltage is determined. After that, the wire is soldered or screwed so that it is connected to the desired terminal.