How to Connect a Rear View Camera • BYRGPUB.COM

How to connect a rear view camera?

If you decide to install a rear view camera, please note that different models are available and one instruction on how to install a rear view camera does not fit all options. First, the installation is done in different locations. Secondly, the connection can be made, both for continuous operation of the camera, and for turning it on only when the engine is started.

The connection diagram is still almost the same for all models, it only requires clarification where to install the rear-view camera. It is also clear that this device in the conditions of modern traffic becomes simply irreplaceable on the roads and greatly simplifies the life of the DRIVERS.

Rear view camera connection diagram

In the question of how to install a rear view camera, you will NOT be mistaken if you know what is connected to what. We have 3 wires. Black (“minus”), red (“plus”), yellow (“video”). Our task is to connect the yellow connector to the input of the monitor or TV. Connect the black one to the battery ground, the red wire is connected directly to the camera.
If you want the monitor to turn on automatically when the car is driving backwards, connect the dedicated wire to the reversing lamps. Such a wire is provided in those models that have a similar function. Pay attention to the wires, and do not mix it up, as this is fraught with damaged equipment if your model does not have adequate protection, when the gadget simply does not work.
Many camera models have “outlets” wires. You just need to connect the coaxial video cable. Power cord is also included.
There is such a connection method when you need to crimp the wire and connect through the appropriate connectors. Some manufacturers have taken care of those buyers who do not know how to connect a rear view camera and therefore simplified the task by implementing a standard RCA connector known to all as “tulip”. It just needs to be connected to the video input on the radio.

Camera power

The camera is powered by an electric current with a stabilized rectified voltage of 12 V and a power of no more than 0.7Am. Some models have short-circuit protection at the outputs. Remember that according to the instructions for use, this device will last a long time, if you observe the temperature regime from 10 ° C to 40 ° C and the air humidity does NOT exceed 80%.

The video signal from the camera to a TV, portable DVD player, etc. Passes through a regular coaxial cable. These cables are used in everyday life in order to connect ordinary television equipment.

Purpose and operation of rear view cameras

The function of this equipment is to facilitate car parking or reversing. The camera is indispensable in conditions of limited visibility or with a small space for maneuvering. The camera in traffic jams and in dense traffic has also justified itself as a means that additionally prevents collisions due to an incorrectly selected distance by a vehicle walking behind.

The camera is very tiny, with a diameter of about 2 centimeters with a viewing angle of almost 180 °. Cameras broadcast a fairly clear color image. With a sensitivity of not less than 0.1 lux, it is realistic to see objects in the dark. Cameras are produced in a waterproof design.

How to choose and connect a rear view camera to the car, Step by step instructions

Whether or not to put a reversing camera, each driver decides for himself. Connecting a rear view camera requires some well-known and skills, so not everyone can do it on their own. With a small set of tools and initial skills in working with them, you can easily figure out how to connect a rear view camera.

Side mirrors, and even your head turned 180 ° will not give the desired effect, some little things, and maybe NOT little things, you still may not notice. And then dismantling with the owner of the scratched car may begin, and this can cost you tens of times more than connecting a reversing camera. Further in the article, we will consider which camera you can choose, whether a Chinese manufacturer is right for you, or if you prefer something more solid. We will also discuss whether it is possible to install a rear-view camera with your own hands, and how to properly connect your chosen device.

How to choose a camera

The modern electronics market, and especially China, is overflowing with a variety of cameras, and this makes the choice of the right thing more complicated. In order to make your job easier, decide on the priorities that you care about more. price or quality. Not everyone needs high definition cameras, or cameras that can show even in poor lighting conditions. For some DRIVERS, an inexpensive rear-view camera for the radio is enough.

In what resolution the camera writes, the higher the video resolution, the better the recording quality. And high definition of the image is not always needed.
The next moment. camera sensitivity to lighting. In cheaper models, recording quality in low light can be very poor. Therefore, if, due to circumstances, you often use the car in the dark, then at this moment it is worth paying attention.
If you have already decided before buying where you will put the rear view camera, then you need to Pay attention to the installation method of this particular model.
The next moment. this angle of view that captures the camera lens. Usually it is in the range from 120 to 180 degrees. It is better to take something in between These two indicators, so that you have a good rear view, but there was no panorama, because with it the reality is distorted.
Selection of the monitor on which the camera will display the image. But if you already have a radio with a screen in your car, then you just need to think about how to connect a rear view camera to the radio.

How and where should it be installed

Later in the article, we will look at how to install a rear view camera. There is more than enough room in the car to install a video camera, but we need the most advantageous position. There must be a good view through the camera peephole, which is NOT limited to any machine parts. Any camera will reach its full potential if it is Installed in the Best Place.

In our case, such a place is a niche above the rear bumper of the car; the camera should be placed in its upper part above the state number of the car. What does it give. viewing angles, your car radio will only show the road, not parts of your car. But it must be arranged so that it is not strongly recessed, but also does NOT stick out.

True, there is a minus here. your camera is accessible to dirt and the wrong hands. If you place it inside the cabin on the rear window, then half of the screen will be occupied by the trunk, the viewing angles will decrease and the image quality due to glass will suffer to some extent. But on the other hand, it will be clean and inaccessible to strangers.

So you personally have to calculate all the pros and cons of the external and external location of the camera.

The procedure and diagram for connecting a rear view camera

And now in more detail about how to install and connect a rear view camera to a Pioneer radio. Why this model, because it is the most common. If you are installing the radio tape recorder yourself, we advise you first to get acquainted with the connection diagram of the radio tape recorder in the car.

If we take into account the insecurity of our video camera, and the best view, then its place should still be above the number, outside. It should be installed closer to the edge to improve visibility, but not so that it is exposed. The installation of the camera itself is not a big deal. The camera has a bracket required for installation, you only need to drill a couple of holes for the mounting bolts, and one hole for the cable.

And then the rear-view camera is included in the general electrical network of the car. If you are NOT strong in electricians, then it is better to Contact a car service specialist, but if you have at least basic knowledge, then you can quite figure it out on your own. So, the order of connection is in stages:

Any camera has two wires, one for transmitting the video signal from the camera to the monitor, and the other for power. Since the camera itself has short wires, you will need to extend them so that they are enough from the front panel to the end of the trunk (as a rule, an extension cable for the video signal is included in the kit).
Where can I get power for the camcorder? Usually the camera is connected to the rear light. Therefore, immediately after turning on the reverse, the rear view camera is also turned on.
All wires stretched through the cabin and in the trunk must be secured and hidden. This will help avoid unexpected network interruptions while driving.
If you use a monitor instead of a radio, you will need to find a power source for it. If you have a Pioneer multimedia recorder, this issue is solved automatically.

Connecting a reversing camera to a Pioneer radio

Now we will specifically talk about how to configure and connect the reversing camera to the Pioneer radio tape recorder. There are small nuances here that mislead everyone. Connect the camera to the reversing light, all power is on the camera, then the wire through which the video signal will go. In Pioneer, this is a brown tulip, not to be confused with yellow. We go into the settings, find the section in the rear view camera menu, put the item on, and switch the polarity to battery mode.

Our camera works, you can check it, go to the main menu and select the camera icon, but it will NOT turn on automatically. This can be fixed by connecting the purple wire to the taillights (where the camera is). In total, when reverse gear is turned on, the lamp lights up, power is supplied to the camera, and the radio tape recorder understands that it is necessary to switch to reverse gear. The whole connection diagram of a rear-view camera is quite simple, and therefore most drivers often cope with its installation on their own. In cars equipped with automatic transmission, accidental activation of the rear view camera may occur.

To eliminate this problem, you need to install an additional camera turn-on delay sensor. In each car model, the installation of the camera may be different, but in the details, the principles of connection are similar. The process of connecting to video cameras that transmit a signal by radio is more complicated, but they have the advantage that several such cameras can be connected. There are more and more cars on the streets of the city, so there is a rear view camera. this is already a necessity. It will not only help you park correctly, but will also preserve evidence of your innocence in the event of a collision.

How to properly connect a rear view camera

Basic wiring diagrams, device connection and pinout of connectors

Rear-view video camera. an excellent solution for controlling the movement of a car in reverse, since the mirrors do NOT allow you to fully see what is behind the car. Although you shouldn’t rely heavily on one video camera, because it also has its drawbacks (switching on with a small delay, limited viewing angle, insufficiently clear resolution).

Connecting a rear view camera requires some well-known and skills, so not everyone can do it with their own hands. have to go to the auto electrician. But the majority of drivers do an excellent job with this task, especially if you carefully read this connection manual.

Usually cameras for video surveillance of the situation behind the car have black on the board on the connector. minus and mass, red power supply, maybe 3.3 volts and 5 volts, yellow. integrated video output. There is also control. white or brown, depending on the manufacturer. Red, black and yellow are generally followed by all camera manufacturers. To check, connect it to the TV through a regular “tulip”. should show.

6-wire rear view camera pinout

Here is the same kitchen as on 3, 4, 5-wire, just separate masses are displayed on each line. Camera wire pinout:

Red wire “” to the reversing light.
Yellow wire “” for tulip video signal.
The rest of the wires are “-” on the video signal tulip.

Backlit camera wire pinout

Infrared illumination on the rear view camera displays the image in color in case of sufficient illumination, and in case of insufficient illumination due to infrared illumination, it displays the image in black and white for about 5 meters. So, their presence on rear-view cameras is relevant, in contrast to registrars, where they have an advertising character of “night shooting” without practical use, which cannot be said about LED backlighting on rear-view cameras. it’s better without them than with them!

Connecting two car cameras to the monitor

The principle of operation is such that when the reverse gear is turned on, voltage is applied to the coil, the rear camera turns on, the power contacts of the front camera are open. When the rear camera is turned off, the relay is turned off and through contact 87a plus is fed to the button. Turn on the button. front camera works.

Installing a parking rear camera

Reversing camera connection (classic). The camera connects to the reverse wiring plus to plus and minus to minus. When you turn on the reverse speed from the reversing light, it goes to the reverse camera, and it sends a signal to turn on the monitor automatically, so no additional manipulations need to be done. The reversing camera is automatically disabled when reversing is disabled. The camera is connected using a cord, which is initially available for wiring next to the camera or using a wire with a plug, for which there is a plug for the camera wiring.

There are even wireless rear-view cameras (video transmitter and video receiver with a radio channel), then the connection will look like in the diagram.

Rear view camera mounting methods:

In the socket for the license plate or in the trunk handle or in the place for the camera. no damage to the car;
Camera in the frame of the room. the hole for the cord is not visible, since it is along the frame;
Cut-in chamber. on the principle of a peephole, convenient among parking sensors, in a lock cylinder or just a case;
On the pin. minimal damage, since the wire passes through the pin itself, imperceptibly, installing the pins up;
Overhead. have a certain angle and minimum dimensions, often have a certain position for installation;
On the bracket. convenient in that you can mount in almost all places and change the angle of the camera and rotate the image.

Please note that all cameras are usually powered from 5 volts, there is a voltage stabilizer in it and gives 3.3 volts to the camera itself, for someone this stabilizer can withstand 12 volts, but this is rare, it usually burns out. On ordinary Chinese cameras powered by 12V from a reversing light, a 5 volt stabilizer is sealed in a plastic fork for power and a tulip wire, the camera itself also has a 3.3 volt stabilizer.

Replacing the rear view camera. instruction

Like any other electronic device, these camcorders sometimes burn out (especially if they are powered constantly). Then the replacement steps will be as follows:

Removing the camera.

Cut off the standard harness from the camera, closer to the camera. It will be in a shielding braid, prepare the braid for soldering with another same braid from a new camera.

Here is a new camera, a cord with a tulip connector. A long cord is attached to it, which should stretch to the very screen. We will NOT need all of it, since our screen has a standard wiring to which we are connected. Cut off the connector with a small piece from the long wire and clean it. There will be a central core inside the braid. We’ll need both.

Soldering the wires of the cut off standard harness to the new camera:

Yellow on standard. to the central vein, cut by a new chamber.
Braid from standard to braid from a cut new camera
Black for regular. to the cons of the wires on the new camera (usually black)
The red from the new camera must be connected to the positive wire supplying the reversing light (green with a white stripe)

Turn on the ignition, put the automatic transmission selector in position R. If there is an image. everything is done right.

If you ask the camera from the reversing light, there may be ripples on the screen when you turn on the camera. will have to be connected from the supply plus through the relay. Disabling it is mandatory, because if you constantly supply 12V to the video camera (for example, from the license plate light), then sooner or later its voltage converter will burn out.

Do not forget to carefully solder and insulate everything, preferably by heat shrinkage. It is advisable to cut the cords with a margin, so that you can quickly replace the camera in the future, and not Disassemble the casing. Before cutting the cords on a standard camera, you need to be sure that it is inoperable. The question of mounting a new camera. purely locksmith and solved without problems. It is better to take an infrared camera. she “sees” better in low light.

The last thing a driver wants to do is damage the car while parking on a busy street. Especially if it’s someone else’s car.

And the truth is, no matter how experienced the driver is, there is a subtle little thing that will cause trouble. In such a situation, a rear view camera comes in handy. It significantly improves visibility and avoids unpleasant excesses.

Today, many cars are equipped with this useful gadget, especially the premium segment. But early models lacked such a function, which means. there is a reason to pick up a tool.

How to connect a rear view camera to a Chinese radio tape recorder today will be discussed.

How to choose a system

The automotive electronics market abounds in a variety of connectivity kits. This is especially true for products from China.

Indeed, for some owners, the quality of the transmitted picture or the backlighting in the dark is not at all critical. So not worth paying money for unused features.

For a better understanding of the devices presented, you need to understand the basic parameters. These include:

Video resolution. The higher this parameter, the better the video quality is on the screen. High-resolution cameras provide detailed images of the smallest objects behind the car.
Matrix sensitivity. Sometimes this parameter is indicated by the “ISO” symbol. Cheap models are not equipped with sensitive matrices, this directly affects the image quality in the dark. The picture is fuzzy, it floats while moving.
Shooting coverage. The standard viewing angle range is 120-180 degrees. A high value helps to make the video panoramic, a lot of space will fit into the frame. But there is an insidious moment: at such angles, the real dimensions of objects are distorted, which can deceive an inexperienced driver. Therefore, the optimal solution should be sought between These values.
Camera body and installation type. Waterproof devices can be safely installed outside the car, they are not afraid of water and dirt. But they will always be available to thieves. Indoor cameras are installed in the luggage compartment. Space coverage will decrease, but the device will always be dry and protected from prying hands.
Connection type. Standard. wired connection. A cable is laid from the monitor or radio to the back of the car. unusual is the wireless connection. The driver does not need to remove the trim and hide the wiring. But this method requires additional accessories. transmitters.
Rear cameras with backlight function. With such devices, you can easily navigate in the dark. Illumination is carried out by infrared diodes or an additional lamp. This function is useful for those cars in which the taillights are small and give a low light. Do I need this type of cameras. the owner decides individually.

You must also pay attention to the method of displaying the image. It can be a separate monitor or a 2din radio with a built-in screen. If the quality of the latter suits, it makes sense to install a second monitor.

How to connect a camera to a radio tape recorder with your own hands

Initially, you need to choose an installation location. There is enough space in the back of the car, but when you take into account the coverage of the broadcast picture, the choice decreases.

It is worth considering the location of the camera eye. He must have a view over the entire shooting angle and NOT be obstructed by other body elements.

There are two installation options: under the license plate and under the rear window. Here it is worth considering the type of car body. For station wagons, due to the lack of a long trunk, both methods are suitable. For sedans, the best place. in the license plate compartment.

Let’s move on to the connection. Before starting work, you must prepare the tool:

The camera kit itself with wires;
Screwdriver;
Keys set;
Pliers;
Knife;
Plastic ties;
Electrical tape or heat shrink tubing.

Sometimes you may need to drill multiple holes to mount the rear camera. In this case, you should stock up on drills and a drill. Some car models have a prepared place for the camera, for which it is enough to pull out the factory cap.

Prepare the vehicle interior for wiring. Pull the upholstery gently. Choose a location where the cable will not be deformed by the feet of passengers and avoid sharp bends in the cable. It will be reliable to strengthen the wire on the standard highway cars. Strengthen the main line with plastic ties.

Let’s move on to connecting a rear view camera to a Chinese 2din radio tape recorder. To get to the ISO connections and the rear of the audio system, you need to carefully open the front panel (or several, depending on the car) of the torpedo, and Unscrew the fastening screws. The head unit can be detached.

Advice: for the safety of the electrical circuits of the machine, all connections should be made with the battery disconnected. This eliminates the risk of accidental short circuit to ground.

Diagram of connecting the camera cable connectors to the car radio

When the preparatory work is completed, the cables are laid, you can proceed to connecting all the system components.

Let’s take a closer look at the diagram:

A standard connection cable consists of two parts:

Yellow. signal;
Red. food.

Please note that voltage wire colors may vary on different models.

The connection of the video signal is carried out through connectors of the “tulip” type.

The standard method for powering and activating the camera is through the reversing lights. The principle of operation is as follows:

The red wire connects to the lights, the black one. per vehicle weight.
The signal cord, through the trunk in the passenger compartment, is connected to the radio tape recorder through the Video In.
When you turn on the reverse, a voltage appears on the supply conducts the camera, which activates it.
The radio tape recorder detects the signal on the input channel and switches to the image broadcast mode.

Very often, the radio is connected via the ISO connector. In this case, you should familiarize yourself with the connection pins and find the video input.

The second connection method allows you to activate the surveillance system regardless of the reverse. For this, 12V is supplied to 2 wires. Red and blue. The first is connected to the ignition switch, to the key1 position. ACC. The second is supplied to the reversing lamps.

With this method, the system will operate in two modes:

When shifting into reverse gear;
In key positions key1 and key2. Ignition, which corresponds to the included vehicle electrical system and ignition.

Some models of radio tape recorders require manual activation of the shooting mode in the “settings” of the device. After activation, you should check the work in different key positions, especially in key2.

The next step. adjust the radio itself, namely focus, sharpness and light sensitivity. Different systems offer a different set of settings, so configurations are individual.

Tip: It is important to observe strict correctness when connecting the wires. In order not to be mistaken, it is recommended to assemble the system on a table and configure it. When connecting the supply components to the vehicle network, protect them with fuses.

Connecting a car reversing camera to a laptop

To be able to view the picture on a laptop, you need a special TV tuner. It can be used to match an analog signal with a computer.

The connection principle remains unchanged. The supply wires are supplied with a voltage of 12V, and the tulip is a video signal. to the tuner. Shooting is controlled through software.

Ways to connect two Chinese cameras to the radio tape recorder

On the market Models for dual-zone monitoring of the machine space are presented. in the front and in the back. This solution allows you to register Potential emergencies on the road, and Fix the state of the car in the absence of the owner.

Connection and configuration is carried out in the following order:

The on-board network of the car is de-energized;
The front camera is installed on the rear-view mirror holder;
Mount the back;
For aesthetics, the connecting wires are led to the main module under the passenger compartment trim;
If the head unit has two Video In. Connect signal wires to them. In the case when the kit has its own recorder. choose the place of its installation, connect to the network and cameras;
We check the connections according to the installation diagram, turn on the battery;
Configuring the parameters of the cameras.

It remains only to test the system in motion and, if necessary, make corrections.

Sometimes it happens that one of the cameras does not provide adequate coverage of the space in front of it. Exit. purchase an overlay “Fish Eye”. It acts as a wide-angle lens and widens the angle of view.

How to connect a mirror with a rear view camera

The way to connect such a mirror is no different. The connection diagram looks like:

Often, sets of mirrors with cameras can take power from the cigarette lighter, through their own connector. The owner can choose which voltage supply method suits him best.

expensive mirrors support both sides of the vehicle. The front camera is already integrated into the product body and does not require connection.

Connecting a Chinese rear view camera to a Japanese radio

Lovers of high-quality audio systems Japanese equipment. But they have their own nuances when connecting video cameras.

Consider an example on a Pioneer 2din radio tape recorder. Installation has a similar procedure:

The camera is powered from the reversing light.
The signal cable is connected to the Video In connector. Usually, in this model, a brown tulip responds with theft of the video.
We check in the settings the inclusion of the camera and its operation.

The system works, but automatically, when driving backwards, it will not turn on. It is enough to connect the purple wire of the head unit to the rear lights, where the camera is. The problem will be fixed when the reverse gear is engaged. The radio tape recorder will understand that you need to activate the shooting mode.

The rest of the installation points of the device remain the same.

Rear-facing or front-facing cameras have proven themselves to be the best among car enthusiasts. With their appearance on board the car, it becomes easier to navigate in confined spaces. Their correct installation requires some knowledge from the owner. But with the advice given, any driver can do it.

Whether or not to put a reversing camera, each driver decides for himself. In this article, we will tell you how to connect a rear view camera, and it’s up to you whether you need it or not. Connecting a rear view camera requires some well-known and skills, so not everyone can do it on their own. But if you nevertheless decide that the installation of a regular rear view camera is necessary for you, then use the tips from this article. With a small set of tools and initial skills in working with them, you can easily figure out how to connect a rear view camera.

Side mirrors, and even your head turned 180 ° will not give the desired effect, some little things, and maybe NOT little things, you still may not notice. And then dismantling with the owner of the scratched car may begin, and this can cost you tens of times more than connecting a reversing camera. Further in the article, we will consider which camera you can choose, whether a Chinese manufacturer is right for you, or if you prefer something more solid. We will also discuss whether it is possible to install a rear-view camera with your own hands, and how to properly connect your chosen device.

How to choose a camera

In what resolution the camera writes, the higher the video resolution, the better the recording quality. And high definition of the image is not always needed.
The next moment. camera sensitivity to lighting. In cheaper models, recording quality in low light can be very poor. Therefore, if, due to circumstances, you often use the car in the dark, then at this moment it is worth paying attention.
If you have already decided before buying where you will put the rear view camera, then you need to Pay attention to the installation method of this particular model.

How and where should it be installed

True, there is a minus here. your camera is accessible to dirt and the wrong hands. If you place it inside the cabin on the rear window, then half of the screen will be occupied by the trunk, the viewing angles will decrease and the image quality due to glass will suffer to some extent. But on the other hand, it will be clean and inaccessible to strangers.

So you personally have to calculate all the pros and cons of the external and external location of the camera.

The procedure and diagram for connecting a rear view camera

And now in more detail about how to install and connect a rear view camera to a Pioneer radio. Why this model, because it is the most common. If we take into account the insecurity of our video camera, and the best view, then its place should still be above the number, outside.

It should be installed closer to the edge to improve visibility, but not so that it is exposed. The installation of the camera itself is not a big deal. The camera has a bracket required for installation, you only need to drill a couple of holes for the mounting bolts, and one hole for the cable.

Any camera has two wires, one for transmitting the video signal from the camera to the monitor, and the other for power. Since the camera itself has short wires, you will need to extend them so that they are enough from the front panel to the end of the trunk (as a rule, an extension cable for the video signal is included in the kit).
Where can I get power for the camcorder? Usually the camera is connected to the rear light. Therefore, immediately after turning on the reverse, the rear view camera is also turned on.
All wires stretched through the cabin and in the trunk must be secured and hidden. This will help avoid unexpected network interruptions while driving.
If you use a monitor instead of a radio, you will need to find a power source for it. If you have a Pioneer multimedia recorder, this issue is solved automatically.

Connecting a reversing camera to a Pioneer radio

Our camera works, you can check it, go to the main menu and select the camera icon, but it will NOT turn on automatically. This can be fixed by connecting the purple wire to the taillights (where the camera is). In total, when reverse gear is turned on, the lamp lights up, power is supplied to the camera, and the radio tape recorder understands that it is necessary to switch to reverse gear. The whole connection diagram of a rear–view camera is quite simple, and therefore most drivers often cope with its installation on their own. In cars equipped with automatic transmission, accidental activation of the rear view camera may occur.

Often, a reversing camera is installed after purchasing a new radio tape recorder, in this case we have an article “how to connect a radio tape recorder” in which you will learn about adapters, adapter frames and much more.

DIY installation of a rear view camera. instruction

Rear View Camera. perhaps one of the most controversial elements of tuning, in which motorists constantly argue. According to some, the installation of a rear view camera. meaningless and refers more to “show-off” and “bells and whistles” rather than useful assistants, which drivers use every day. Others consider them a vital element, as well as the most useful invention after the car, and regularly use them when parking, or leaving (entering) the garage.

In my opinion, opponents of the rear view camera. These are the so-called “Old Believers” drivers, these are experienced drivers who DO NOT accept any innovations and useful options, they are “brutal” and use only a rear-view mirror. For them, the car has remained just a means of transportation, and they do not want to keep up with the times, therefore, they DO NOT accept anything new and making life easier. Personally, I believe that everything the owner does with his car. his personal file, except if it helps him live or drives a car. why not? Better a rear-view camera than the innocent face of some lady who drove in your backside or side with the words: “Oh, I haven’t calculated the rumors” or “I’ve only been driving for a month and I don’t know how to reverse.” My article today is for those who are racking their brains over how to install a rear view camera with your own hands. I will try to tell you in detail how to do this, supporting each step with informative photos.

So to your attention detailed instructions on how to install a rear view camera

In my car, I used the RM116B camera model, it’s not critical, you can choose another one, according to your taste. It is best to place the rear-view camera closer to the license plate lights, slightly drowned it in the body of the bumper, away from eyes.

The easiest way would be. installation of a rear-view camera near the room lighting lamp, on a plastic rim, but in this case it will be visible and against the background of white numbers it will stand out strongly.

Taking into account such features, I decided to “push” it deeper into the bumper right above the license plate. that is, in the bar that holds the lighting lamps. In short, now there will be no problems with the holder, which is already good, the mount will be hidden and there will be no need to pick the bumper. In order to repeat what has been done, you need to empty the luggage compartment and remove the frame with numbers.

You need to withdraw through the left hole, so that the length of the wire is enough.

Due to the deep location of the ramp, the rear view camera leg had to be slightly modified by lengthening it. This may be unnecessary for your camera model. In my case, the issue was solved by simply using a metal plate of about 4×6 cm.

The next step was to drill a hole for the reversing camera lens. Here everything needs to be calculated properly, so that later you DO NOT have to add or rewind, in other words. “Measure seven times. Cut one!”

Installing a rear view camera is also unpleasant because you have to mess with the wiring. I advise you to pull it into the luggage compartment using a plug or a hole in the area of the rear bumper or spare tire.

Now it’s time to start the installation work and connecting the camera to the monitor, as well as laying the wiring in the car.

First of all. Remove the decorative trim for the trunk sill and the left side of the trunk trim, then remove everything unnecessary from the passenger compartment: seats, mats, door sills, etc. You will need access to the rear of the radio, so remove it and carefully Examine the connectors.

I took the positive wire from the left rear headlight, I have the color of the wire. white with a red stripe, it is connected to the lamp. The connection itself was made a little further, so that it was less noticeable. I am attaching the wiring diagram, so there shouldn’t be any problems.

In the area of the torpedo, I found a “plus” from the reversing light.

Next, you need to act very carefully, laying the wires. troublesome business. Using “native” fasteners and clips. When the wiring is laid, do not rush to collect everything, first check the functionality and correct connection of the equipment. I don’t need to tell how to test, I think everyone understands that if there is a picture and everything works fine. then the camera is installed correctly.

If the test is successful and the rear view camera works correctly, adjust the position of the camera and proceed to assembly in the reverse order.

Here, in fact, is the whole installation.

I adjusted the lens a few days after installation, it is quite difficult to do it right away, because it is not clear at first how and where exactly the camera should look. The viewing angle is approximately. 120 °.

Afterword.

Installing a rear view camera is not important with your own hands or in a service. this is a significant saving of money, an opportunity to get invaluable experience, and the joy of doing your own work. Try it, maybe you will come out even better than me, as you can see in my case it came out pretty well too. For those who doubt it or not, I will answer. it is better to spend money once and “sweat” over the installation of a reversing camera, rather than constantly “steaming” in tight parking lots and pays for your own and other people’s repairs.

Sources:

http://caraudioinfo.ru/magnitoly/kak-podklyuchit-kameru-zadnego-vida.html
http://ravon-r2.ru/kak-pravilno-podsoedinit-kameru-zadnego-vida/
http://www.Autoposobie.ru/ustanovka-kameryi-zadnego-vida-svoimi-rukami-instruktsiya/