Blow out the 3.5mm jack with a hair dryer

Blowing out the 3.5mm jack with a hairdryer can help solve the problem. As with previous cases, there is no specific purge technique. One thing to remember is that prolonged hot air blowing can be detrimental to the iPhone battery.

Multiple charging cable / headphone connection

Another method based on cleaning the charging connector and audio output. Even the needle is not able to reach the hard-to-reach places of the connectors, but the connectors fill the entire connector, as a result. the maximum cleaning takes place. The principle of operation is extremely simple: perform a forced restart of the iPhone, and after about 10-15 times, connect the charging cable and headphones to the corresponding connectors.

Clean the power connector

Cleaning the power connector in the same way can solve the problem. The method is the same. a cotton swab / needle / toothpick is moistened in alcohol and with its help the power connector is cleaned, be it an old 30-pin connector, or Lighting. Please note that it is necessary to wipe the connector thoroughly.

No sound on iPhone without headphones. what to do

There are many reasons why an iPhone may freeze in headset mode and stop playing sounds from an external speaker. In most cases, dirt or moisture getting into the 3.5mm jack is to blame, but it also happens that there is a software error. In this manual, we have analyzed all the most effective ways to solve this problem, regardless of what caused it.

Note: The solutions to the problem are arranged in order of their effectiveness. Go from the first method to the last one and one of them will definitely help.

Connect a bluetooth headset / speaker

It also happens that the iPhone freezes in headset mode due to a software error. They usually happen after installing a new version of iOS. In this case, connecting a wireless headset or speaker and then disconnecting the headphones helps out. The principle of action is as follows:

Connect a Bluetooth headset / speaker to the iPhone in order to output sound to it.

Disconnect your wireless device.

Immediately after that, you can check if the sound has returned to the speaker of your iPhone.

Clean the 3.5mm jack

The most common cause of iPhone locked in headset mode is dust or dirt that gets into the 3.5mm jack. The solution in this case is the simplest cleaning of the connector with any thin object, for example, a needle or a toothpick.

There is no specific cleaning technique. Swirl the needle / toothpick carefully around the inside of the 3.5mm jack for 10-15 seconds, then blow it out. If there is no result, cleaning the 3.5mm jack with a cotton swab dipped in alcohol may help. In addition, you should try to clean the connector with a rolled cloth.

Reboot iPhone with headphones connected

Also, a forced restart of the iPhone with headphones inserted into the 3.5 mm jack can fix the software problem. To perform a “hard” restart, you must hold down the Home and Power buttons and hold them until the Apple logo appears on the screen.

In the event that none of the above methods helped, we are talking about a serious breakdown and only a service center can fix the problem.

What to do if sound disappears on iPhone and headphones are written?

• Insert and remove the plug from the headphone socket. There is a possibility that iOS did not have time to determine that the headphones were removed.
• Connect other headphones. This can really help.
• Reboot device.
• Check the headphone jack.
• Restore or update iOS.
• Service center

Why does the iPhone show that headphones are connected?

There may be several reasons why the iPhone thinks that the headphones are connected: The headphones were disconnected at the moment when some internal system operations were taking place; Using a headset or headphones of poor quality, which adversely affects the operation of the device as a whole; 3.5mm jack defect.

What to do if the phone thinks it is wearing headphones?

If the phone, smartphone on Android or iphone shows that headphones are connected, but they are not there, you need:

• Clean the connector from ordinary dirt with a thin cotton swab. Attention. do not do this with a needle, so as not to damage the contacts;
• Clean the nest from oxidation using the same cotton swab and alcohol.

How to turn off the headphone mode on Xiaomi?

Open the settings, find the section “All applications”. Find “Radio”, click on the name of the application. You clear the data by clicking “Clear All”. Only then turn off the headphones.

What to do if there is no sound in the headphones on the phone?

You may have accidentally muted the sound. 2. Try plugging in headphones, holding down the volume up button, and pulling out the plug from the headphone jack. Also try pulling and inserting the headphone plug several times.

How to set up headphone sound on iPhone?

The mono balance can be adjusted to increase the volume of the right or left channel. Enables or disables the Mono Audio feature and adjusts the balance. Select Settings General Accessibility Mono Audio.

How to turn off speakerphone on iPhone?

• During a call, activate the iPhone screen.
• Press the Speaker button so it goes out of white.

Causes of the problem

There can be many reasons why the iPhone does not play sound through the speaker. First, let’s figure out how it works. The smartphone “knows” about the state of the headphone jack by measuring the resistance of the circuit. When the contacts inside the connector are closed, the phone “understands” that the headphones are connected and the sound needs to be output through them, and not through the speaker. Accordingly, the speaker is muted and the signal is sent to the connected headphones. However, false short circuits are also possible without connecting devices, then the speaker of the phone is disconnected by it itself, and the sound empty sound jack.

Here are the most common reasons for this:

• The problem with the headphone jack itself on the smartphone.
• Poor quality headphones coupled with software glitch.
• Software glitch right at the moment the plug is pulled out.
• Unlicensed software.

These are the most common causes of a problem. We will analyze how to eliminate.

Change of headphones

If you have used inexpensive (very inexpensive) headphones, then the problem is most likely with them. Connect another device and restart iPhone. To avoid such problems, use branded original headphones and headset.

Cleaning the connector

It boils down to cleaning the headphone jack (for the iPhone 6 it’s 3.5 mm, for the seventh and older Lighting). Dust can simply get into the connector or it can oxidize if moisture gets in.

For cleaning, you can use a cotton swab, needle or toothpick. Additionally, the walls of the connectors can be treated with alcohol.

Another option is to blow through the hole. Alternatively, you can use a vacuum cleaner. If you don’t mind spending money, you can buy a can of compressed air, which is designed to clean electronics.

Another option: turn the headphones on and off the phone several times (possibly up to 10-15). This operation will also allow you to clean the connector, because the headphone plug fits snugly into the hole.

It is worth noting that the manufacturer’s technical support recommends the latter method, since in this case there is no need to insert foreign objects into the connector, which means that the risk of damaging the inside of the smartphone is minimal.

Reboot

Sometimes, simply restarting your iPhone with a wired headset connected is enough. If a regular reboot does not help, it is worth resorting to a Hard Reset. Usually, for this you need to simultaneously hold down two buttons: Power and Home. It is necessary to keep them until the brand logo appears on the screen.

When the iPhone thinks it has headphones in it

Apple smartphones are known to be some of the most reliable. However, even with them, problems sometimes arise. A fairly common failure is the lack of sound from the speakers. At the same time, the gadget writes that headphones are inserted into the smartphone, although the connector is empty. This problem occurs in the IPhone 5, 6 and others, in all, where there is a jack for connecting a wired headset. We will understand the causes of the problem and how to fix it.

Connecting a wireless headset

Connect a wireless headset (or any other Bluetooth device for audio playback) to iPhone. In this case, it is worth observing the following sequence of actions:

• Connect wired headphones;
• Create a pair with a Bluetooth device and output sound to it;
• Disconnect wired headphones;
• Disable the wire-free device.

How to fix

So, the sound on the iPhone disappeared, it says that the headphones are connected, what to do in this case. Most often, the problem can be solved literally within a few minutes by following the tips below.

Software errors

Software problems that can lead to loss of sound are as follows:

• Incorrectly configured
• OS braking and freezing.
• Unsuccessful jailbreak that resulted in a code error on the iOS operating system.
• Using various unofficial software.

Possible reasons for no sound

All the reasons that are associated with the loss of sound on the iPhone actually relate to either hardware or software.

There is no sound at all

If the iPhone does not make any sounds at all, then this means that the problem lies elsewhere, and it is more serious.

But it is still recommended to first clean the connectors (all this is described in the previous paragraph).

If the smartphone is completely silent, then the problem can be both at the hardware level and at the software level.

You should try the traditional method that will help you troubleshoot problems that have occurred at the software level.

Before proceeding with this method, you need to take care of the safety of data on your smartphone. That is, you need to make a backup to the iCloud cloud or iTunes.

After the user has taken care of their data, you need to reset everything from the phone.

Now it’s the turn of the firmware. It needs to be updated.

After completing the steps, you need to boot the iPhone.

Well, the next step, the last one, is to check the sound.

If, after all these steps, the situation has not improved a bit, then the problem is still at the hardware level.

Anything could break. from the buttons themselves to the board and the Audi codec. Therefore, in such a situation, it is imperative to contact the service center for specialists to provide professional assistance.

As a rule, repairing a sound-related smartphone, even an expensive iPhone, costs adequate money. Therefore, do not be intimidated, and in case of any problems, it is better to contact a specialist. Especially if the owner of the “apple” gadget has absolutely no experience in repairing it.

I lost sound on my iPhone, what to do?

In such situations, when audio drops on the iPhone, the user himself is unlikely to be able to determine the true cause of this problem. Therefore, it would be better to figure it out right away so that in the event of a sound loss, take the right measures and eliminate the deficiency.

Of course, this is trite, but the iPhone with the missing sound does not already match the functionality of another smartphone. After all, it can not be used either as a means of communication, not as a player.

It is worth reassuring all Yablokoy owners at once. There is no need to prepare a large amount for repairs. After all, the main thing is that the gadget is in good working order mechanically. It is in this case that the user can even solve the problem himself.

Hardware problems

The more popular and common hardware problems that cause loss of sound include:

• The speaker has been mechanically damaged. The most common cause of this breakdown is mechanical impact on the iPhone. As it is correct, the service center will offer the user to change the speaker or a non-working microcircuit. Of course, all this can be done by the owner of Yabloko himself, only if he already has a positive experience of disassembling smartphones in the past.
• Clogged holes in the smartphone. If the iPhone owner is one of those who usually carry their smartphone in a or bag without using protective covers, then most likely the reason is that the device’s speakers are clogged. Also, the rest of the connectors and speaker grids are very quickly clogged with dust and dirt.
• Liquid ingress. Due to the ingress of liquid inside the case, various microcircuits can oxidize. With this phenomenon, it would be best to contact a service center.

Sound is only available in headphones

If such a situation arises, the owner of an apple smartphone may think that the problem is still with the software, because it is they who are characterized by a partial loss of signals.

For a more accurate statement of the “diagnosis”, you will need to insert headphones. If there is sound in the headphones themselves, and after the user takes out the headphones, the sound disappears, then the problem lies in charging or headphones. Another distinguishing feature of this problem is the inoperative volume up and down buttons.

To be more precise, the problem is that dust has got into the connectors of the charger or headphones. Or they are out of order (namely, oxidized). For these reasons, the iPhone begins to “think” that headphones are constantly connected to it.

It is not very difficult to cope with the problem that has arisen. you just need to clean the clogged connector.

This can be done with an old toothbrush or toothpick.

After the connector is cleaned of dirt, you need to restart the iPhone. And it is worth applying this trick: several times you need to insert and remove the headphones and the charger into the cleaned connectors.

If the above method did not solve the problem, then most likely the reason for the breakdown of the custom iPhone is a little more serious. It must be oxidized contacts. This could have happened for a number of reasons. The most common reason why contacts oxidize is contact with liquid.

Therefore, in order to fix a smartphone, in this case, you will need to disassemble the gadget in order to clean it not only from the outside, but also from the inside.

When you try to fix a smartphone yourself, without enough experience, you can break not only the sound, but also something more serious.

The lack of sound on the iPhone indicates either a software error or a malfunction of the gadget at a technical level. If this error is at the software level, then, most likely, the user will solve this problem on his own. The main thing is that his assistants have a stationary computer (or tablet) with downloaded iTunes. If the problem is still at the physical level, then you will need either more experience in working with the internal contents of the smartphone, or you just need to contact the service center to provide professional assistance.

What to do if sound disappears on iPhone?

An ordinary user will hardly be able to accurately diagnose the cause of the loss of sound. Therefore, you will have to take measures aimed at eliminating all sorts of reasons. starting with the simplest.

Perform a visual inspection of the gadget. The reason for the lack of sound may lie “on the surface” and consist, for example, that the speaker is covered with a film or a cover.

Restart your gadget. As a result of the restart, the cache will be cleared, temporary files will be deleted, and iOS will start working again. A reboot can eliminate a cause such as a freeze of the operating system. If after launching the iPhone there is still no sound, you should exclude this reason from the list of possible ones and move on.

Reset the settings. With this action, you will bring all the settings of the mobile device to the initial configuration. Follow the path “Settings”. “General”. “Reset”, click on “Reset all settings”, then enter the password twice.

A reset of this type will not delete the user’s personal data, therefore, it is not necessary to create a backup before this operation.

Uninstall apps. Remember which of your actions preceded the loss of sound. Perhaps you installed a tweak from Cydia and then immediately discovered the problem? “Take down” applications and tweaks that you downloaded recently, reboot the device again and check the sound.

Back up your data in any way you want. The following operation will delete information on the iPhone.

Restore the gadget through DFU mode. Connect iPhone to PC with cable, open iTunes and enter “apple” device into DFU MODE. How to start DFU mode is described on our website. When iTunes prompts you to restore your gadget, answer yes.

If none of the above measures worked, there are no software errors. the problem lies at the hardware level. All that the user can do in this case with his own hand is to clean the headphone jack and speaker.

This work must be done as carefully as possible! Do not use metal tools (such as a needle), otherwise you risk scratching the contacts. You can remove dirt from the 3.5 mm connector with a toothpick or a thin cotton-tipped stick.

It is best to use a dry brush with soft bristles to remove debris from the speaker.

If cleaning does not work, you will have to come to terms with the fact that the iPhone needs professional repair.

Hardware problems

Hardware problems that can lead to the loss of sound during a call and in the speaker are as follows:

Filling. Due to the ingress of liquid under the case, the headphone jack microcircuits are oxidized. Because of this, the iPhone constantly “thinks” that a headset is connected to it. although the 3.5-Jack connector is actually free. It is better to “cure” the iPhone from flooding in a service center, but “first aid” should be provided to the gadget with your own hand. Our article tells you what to do if your iPhone falls into water. Clogged speaker or headphone input. This problem most often affects people who prefer to carry iPhones in their s without using protective cases. The speaker mesh and 3.5-connector are inevitably clogged with small debris and dust. Mechanical damage to the speaker. Breakdown of the speaker is a result of physical impact on the mobile device. In this case, you need to replace the speaker or at least a non-working microcircuit. The replacement can be done by a person who knows how to disassemble iPhones and owns a soldering paw.

Software errors

Common software reasons for missing sound include:

Unsuccessful jailbreak. Hacking the system can lead to an error in the iOS code. Installation of unofficial software. Only those tweaks should be downloaded from Cydia that have been verified and recommended by experts on thematic portals. The operating system freezes. Incorrectly set iPhone settings.

IPhone has lost sound. what to do?

There are many reasons why sound can be lost on iPhone. The user will hardly be able to identify the correct one, so he will have to take various measures in order to eliminate the deficiency. What are these measures, this article will tell.

An iPhone that has lost sound actually loses most of its functions. it cannot be used either as a music player or as a means of communication. Therefore, the user, faced with such a malfunction, is forced to immediately attend to its elimination.

The iPhone owner does not need to immediately prepare for the worst. to call for service and expensive repairs. If the device is mechanically working, then the user will most likely be able to solve the problem on his own.

Why iPhone lost sound: a description of possible reasons

The reasons why the ringing sound or the sound during a conversation most often disappears on the iPhone can be conditionally divided into software and hardware.

Where to carry the iPhone on which the sound has disappeared?

Unfortunately, the loss of sound is usually not the result of a factory defect, but the user’s careless handling of the device. If the iPhone is flooded or if its speaker is broken due to mechanical impact on the gadget (falling), there will be no warranty repair. the seller will return the broken smartphone to the buyer.

Before going to the seller and demanding a free fix, the iPhone user should look into the SIM card slot. There is a humidity sensor. if it is red, then you can not count on the seller’s assistance. iPhone is a drowned man and is no longer under warranty.

After the seller refuses, you will have to carry the iPhone to the service center yourself. The table below contains the approximate for the elimination of defects that can lead to the loss of sound:

Downed mode

The first reason for our problem may be a banal reset of the set settings. That is, if you notice that you have lost sound on the iPhone 4, you should not immediately panic. Check if everything is ok with the settings.

Most likely, you will notice that you have a silent mode. It is enough to change it to any other, and the problem will disappear by itself. Basically, this is a very common case. But unfortunately, more often subscribers think about the problem if the situation is of a different nature. So what else could be the case? Why is the sound disappearing on the iPhone??

Resetting everything

Don’t want to look for a long time for the cause of the breakdown and loss of sound? Then you can try to do without it. It is enough to reset all iPhone settings to the initial ones. If the reason lies in the operating system of the device or some kind of failure, then it will be eliminated. When can you try your luck? For example, if you lost the lock sound on iPhone.

How to bring your idea to life? Go to smartphone settings. There you need to select the “General” tab. “Reset”. Take a close look at all the points that the system will offer you. Here click on “Reset all settings”. Now you have to wait a while. Don’t be alarmed if the iPhone restarts immediately after processing your request. This is quite normal.

You can see what happened. Practice shows that resetting the settings to the initial ones not only returns the sound, but also generally improves the operation of the smartphone operating system. True, it will take a long time to set up call ringing again. This is not such a big problem compared to the sound disappearing on the phone.

Moisture ingress

What to do if sound disappears on iPhone? It all depends on the situation. Sometimes the cause of this problem is the ingress of moisture into the device. Talking on your smartphone in rainy weather? Dropped it into the water? Then don’t be surprised at the problem! Any phone starts to “glitch” when it comes into contact with water. By the way, high humidity in the room can also cause the sound to drop out.

Here everything is solved quite easily. If the sound disappears on the iPhone (or it disappears altogether) due to moisture getting into the device, it must be dried. Disassemble the phone as much as possible, and then blot each component with a towel. Dry all parts carefully with a hair dryer. The faster you do it, the better.

What’s next? Once the entire smartphone is dry, you can reassemble it and test its functionality. Practice shows that the sound problem usually disappears. You should not be limited only to these cases. Sometimes the sound on the iPhone drops for other reasons. Some of them are very easy to eliminate. And some are not subject to adjustment at all.

Sound drops on iPhone: solution

Often, users complain about a situation in which sound disappears on the iPhone. And it doesn’t matter which model you have. This problem can still bother even the most careful and thrifty person. To be honest, there are a lot of options for the development of events. But we will try to fully deal with them. Why is there no sound on my iPhone? What to do in this or that case? All this will be discussed now.

System crash

By the way, you can try one very tricky trick. It helps when everything is in order with the phone itself. After all, if the sound on the iPhone disappears, you can complain about the usual system failure. Such phenomena can happen on any phone for various reasons.

Usually the situation is subject to a simple correction. First, you can restart your iPhone. Reboot the system. Here’s what will help to get all settings back to normal and eliminate even minor glitches. This is not my favorite trick.

Subscribers often use one trick: if you lose sound on your iPhone, plug it in for a while and then unplug the headset. Headphones. here’s what will help you deal with the situation. This method is very helpful. In any case, this is what most iPhone owners say.

Damaged speakers

The next reason. it is damage to the speakers in the device. This is also a very common case. And just he brings a lot of inconvenience to users. After all, before drawing such conclusions, you will have to exclude all other options.

If you find that you have lost sound on your iPhone or it is now quiet, it’s time to check the integrity of the speakers. It is best to take the machine to a service center. They will tell you exactly what the problem is. If the speakers on the device are really damaged and refused to work, then only one thing will help here. their complete replacement. As a last resort. repair. But you shouldn’t do this on your own. Again, you will have to contact service centers. No other way.

“Pirate

But there are also more unpleasant moments. For example, if we are talking about a pirated copy of the iPhone. Buyers very often complain about eternal problems with the operation of these gadgets. And the sound disappears on them very often.

What can be done? First, try all the suggested solution methods. Most likely they won’t help. Secondly, if your copy of the iPhone is still covered by a warranty, you can use it. Just exchange your phone for a new one. It should be noted right away. this phenomenon is rarely observed. Often buyers of fakes are left with nothing.

Then you can only sympathize. And to suggest from now on not using fake gadgets. Or learn to work with an iPhone without sound, or completely change your phone. But not on “pirate” anymore. There is no other way out.

Have you bought a new device and noticed the sound is dropping out on your iPhone? Most likely, the reason here lies in marriage. Do not hesitate, try to quickly solve the problem. How exactly?

Is the warranty expired? Take your iPhone for repair or replace it altogether. As you can see, there are enough cases when the sound disappears. And you don’t always need to panic. It is often possible to cope with all the problems on your own. If you are afraid to make the wrong “diagnosis”, contact your nearest service center. This will save you unnecessary headaches.

No sound (disappeared) on incoming call on iPhone, what to do?

If the sound of an incoming call or messages has stopped playing on the iPhone, this does not mean that it is time to run to the service center. There is a chance that you have stumbled upon a rare, but not a single bug. A banal reboot or turning on / off the silent mode switch may not help, which is why try using our instructions.

iPhone needs restart

If the volume switch is in the correct position, but the ringtone still does not sound, your device may need to be rebooted. A hard restart will fix software bugs that could have caused the ringtone to disappear. We talked about how to restart iPhone (4 ways) in this article.

What to do if there is no sound (disappeared) of an incoming call on iPhone

Despite the fact that the iPhone is a very reliable thing, sometimes users are faced with a sudden disappearance of the ringtone when making a call. There is an incoming call, but there is no beep, what should I do? Below we will tell you how you can solve this problem.

No sound on incoming call on iPhone. Do Not Disturb is activated

If the ringtone on your iPhone stops ringing, check to see if Do Not Disturb is turned on. Users often mistakenly activate this mode without noticing it. If you see a crescent-shaped icon at the top of the screen, it means that you have Do Not Disturb mode turned on, which turns off all sound notifications.

Solving this problem is very easy. Open Control Center and turn off Do Not Disturb mode. The beep should now appear again.

Do not disturb mode settings can be changed by going Settings → Do not disturb.

Check your sound settings

It is possible that problems with the ringtone arose due to incorrect sound settings. Open “Settings”, select the section “Sounds, tactile signals” and set the appropriate volume of the ringtone and notifications. Here you can also enable “Change with buttons”, which will allow you to adjust the volume of the ringtone using the volume button on the left side of the iPhone.

Troubleshooting with AssistiveTouch

Go to Settings → Accessibility → Touch.

Go to the AssistiveTouch section and activate this function through the corresponding toggle switch. A virtual button with additional menus will appear on the screen, which can be positioned anywhere on the display.

Tap on the AssistiveTouch menu and select “Apparatus”.

On the right there should be a “Mute” icon with a crossed-out bell (if not, then put this function in this position), and on the left, tap on the “Louder” (volume up) button to increase the ringer volume.

Disable AssistiveTouch as unnecessary.

IPhone may be muted

In most cases, the ringtone stops playing because the iPhone has been put into silent (silent) mode. Of course, this explanation is very simple, but often it is this explanation that is the most correct, especially for very “new” owners of the gadget.

To fix this problem, check the volume switch on the left side of the iPhone. If the switch is in silent mode (you can see an orange mark), just slide it, and when a call comes in, music will play again.

Silent Mode On (iPhone Speaker Sound Off):

Silent Mode Off (iPhone Speaker Sound On):

One earphone from the iPhone stopped working: what to do

Unfortunately, the quality of the Apple headphones is poor. Airpods have certainly propelled the company forward in this regard. But after constant use for a couple of months, they also often fail. The most amazing thing is that most often it is one earpiece that breaks, and it is the right one, which contains the microphone and the volume or video recording switch.

It would seem that you have to buy a new accessory or use it in one ear, but there is one catch. All sounds in the phone are reproduced in stereo mode: the song is decomposed into left and right channels. One can hear a voice, and another, for example, the sounds of individual musical instruments. This is why you may not always enjoy the sound quality when listening in one ear.

Airpods may not be supported on older iPhones

The solution to the problem is peculiar, since it does not make the second earpiece work. The point is to set the sound to play only in mono mode. It uses only one canal and all components pass through it to one ear. To switch to mono, you need to go to the phone settings, find “Universal Access” and switch the desired parameter.

Why iPhone can’t see headphones via Bluetooth

Even iPhones, which are the standard of reliable and modern mobile technology, can have problems identifying the headset and other devices via Bluetooth. The most common causes of the problem are:

• violation of the software integrity of the firmware, physical damage to the motherboard and individual contacts of the wireless module;
• various software failures both due to unforeseen actions and during updates;
• conflicts between system and user applications.

Important! Installing software from unverified sources can not only cause the operating system to malfunction and software conflicts, but also the complete or partial inoperability of the gadget.

The adapter must be plugged into the connector through which the iPhone is to be charged

The correct operation of Bluetooth is also affected by increased temperature, moisture, drops or surges in the home power supply during recharging.

How to turn on wired headphones on iPhone

The headset from the iPhone can be easily used on the iPad or iPod touch. If these are wired headphones with a 3.5 mm jack, you just need to insert it all the way into the corresponding jack on the phone. This should be done as carefully as possible, without connecting the accessory abruptly, moving it along the sides. If everything is done correctly, an icon will appear on the display, symbolizing that all contacts in the socket are closed and the headphones are successfully connected.

On iPhone 7 plus, the jet connector is at the bottom

Note! You can perform all these actions with other accessories with a 3.5 mm audio jet, but remember that it makes no sense to connect headphones with an impedance of more than 32 ohms. The power of the phone and battery is not enough to produce the same high-quality sound that they are capable of when connected to a computer or laptop.

16 Easy Ways to Fix iPhone Stuck in Headphones Mode

Why iPhone doesn’t see headphones. what to do

Many people love to listen to music, it inspires and gives strength. It is better to do this with headphones so as not to disturb others, especially since their tastes may not coincide with the musical preferences of the music lover. Sometimes with accessories of this kind, or rather with their connection, problems arise. Owners of expensive technology are not immune from this, as well as lovers of cheap smartphones. It happens that the iPad, iPod or iPhone does not see the headphones. This material will tell you in as much detail as possible what to do if the headphones on the iPhone 7 do not work, how to set up the connection and what to do if one headphone suddenly stops functioning.

How to connect the speaker to the phone via Bluetooth

For users who like to listen to music through speakers wirelessly, the method of connecting a Bluetooth speaker to an iPhone will be relevant. This can be done as follows:

• Put a speaker or a pair of them in close proximity to the phone to ensure future wireless communication. If the distance is too long, the connection may fail.
• Turn on the speakers and switch to pairing mode by pressing the corresponding button on the case. If not, then you should carefully study the instructions for use of the speakers.
• Go to the phone menu and select the “Settings” icon (gray gear).
• In the general parameters window, find the “Bluetooth” item and go to it.
• Switch on the module by moving the slider to the appropriate position. After loading, a list of devices in the immediate vicinity and ready to connect will appear on the screen. The speakers will be displayed under the name of their manufacturer or model.
• Click on the names of the columns and connect to them. Pairing may take some time, most often it takes no more than 2-3 minutes. If the speakers are not visible, you can turn them off and on again or refresh the search list on your phone.
• After pairing, the speakers are ready to use. You can test them, turn on any melody.

Note! Sometimes, to connect to the speakers, you need to enter a password, which is indicated on their case or box. If lost, please refer to the speaker manual.

How to set up headphones on iPhone

You usually only need to set up wireless headphones. If they are used for the first time, then you need to make sure that the latest version of the software is installed on the smartphone. After that, you should perform the following actions:

• Go to Home Screen.
• Open the case with the headphones and place them next to the phone.
• Wait for the setting animation to appear on the display.
• Click “Connect”.
• In the case of the Pro version of the headset, carefully study all the instructions.
• Click “Finish”.

How to Exit Stuck HeadPhone Mode on iPhone 6 & iPhone 6s & Plus

The accessory may not connect due to moisture getting into the phone case

Important! If you are signed in to iCloud, the headphones will automatically set up to work with any supported Apple ID-connected devices.

What to do if the iPhone 7 does not see the headphones and why

First of all, it is worthwhile to understand that headphones for the iPhone, as well as for some other devices, are divided into classic wired and new wireless generation accessories. The latter were called Airpods, they are gaining popularity, gradually ousting the confusing wired devices from the market.

If the iPhone 7 headphones are not working, then it may be due to a hardware failure.

For your information! Since their release, Apple has received many complaints about design and connection issues. If the phone does not see new wireless headphones, then most likely this happened due to errors in synchronization.

The reason for the lack of sound and the impossibility of identifying the device may be:

• operating system updates that were incorrectly installed due to failures;
• dirt, dust or sand has got into the headset jack, as a result of which the phone does not receive contact for detecting and switching to the listening mode from the headphones;
• dirt or, more often than not, moisture has got into the phone case. It could oxidize the input pins for the headset, which also prevents the signal from passing to the processor;
• the smartphone or headphones were dropped, as a result of which the loop responsible for transmitting signals was damaged.

iPhone 7 Plus also suffers from headphone problems

Important! It is a careless attitude to equipment and accessories that causes most of the breakdowns that may not be related to headphones. Do not expose the phone to direct sunlight, leave it in damp rooms, or drop it on a hard surface.

The first thing to do is restart your iPhone or iPad. If that doesn’t work, you can reset all custom settings and updates. Perhaps the problem lies in the software part in which the failure occurred. After restoring the phone, it is advisable to return the backup copies of the updates that were prepared before resetting the settings.

It often happens that some program simply does not allow the phone to turn on the vibration option. You need to remember which updates or software products were recently installed on the device, and uninstall them manually, and then check for the connection and sound.

If water gets into the phone, the contacts may oxidize and the operation of many modules will be impaired. Needed as soon as possible:

• Unscrew the outer screws of the iPhone case and detach the back cover.
• Using a suction cup or a sharpened credit card, carefully remove the display and remove its ribbon.
• Dry the device with a hairdryer and remove oxidation with alcohol, if they appear.
• Assemble the phone in the same sequence.

If after all this music does not appear and the headphones are not detected, the problem is in the connector. It is recommended to carefully clean it with a needle and cotton swab, which will remove dirt and dust lumps that have accumulated there due to wearing in a trouser

The headset may not turn on due to a defective adapter

How to Recall Bluetooth Device on iPhone

It so happens that when using Bluetooth headsets, they accidentally click on the “Forget device” item in the connection settings. After that, the phone no longer finds accessories and cannot work with them. The following sequence of actions can help:

• Turn off Bluetooth.
• Restart iPhone.
• Turn on Bluetooth.
• Search all devices.
• Find what you want and start pairing.

Sometimes this does not help, and then it is recommended to reset the phone and accessories. This is a rather radical method, and sometimes you can do without it. It is enough to try one more step-by-step instruction:

• Turn off the headset.
• Press and hold the “On / Off” and “Synchronization / End” buttons on it simultaneously for ten seconds or until the indicators start blinking alternately.
• Start searching for a headset from your phone (blinking mode. ready to search).

Failure to pair Bluetooth on iPhone is a fairly common error when connecting a headset

Thus, it was sorted out how to turn on wired and wireless headphones on the iPhone 7 and other versions of the popular smartphone. It should be noted that in most cases, the inoperability of components and accessories is associated with the user’s negligence. Therefore, you should carefully use your gadget, and then everything will work properly.

Decision

Turn off your smartphone. Of course, this is not necessary, but just in case it is better to do it.

We need a standard toothpick. If you don’t have one, you can try a match or the tip of a cotton swab. Just be sure to remove the cotton wool itself from the tip, as it can clog in the port.

You can pre-purge the entrance.

Now we clear the entrance. Make circular motions and try to get all the dirt and dust out of there. If you have a model without a standard “ear” port, then we clean the Lightning port in this way (the one where you insert the charger). but do it as carefully as possible.

As you can see, I found a whole layer of fluff, dirt and dust inside. Apparently, carrying it in your for a long time led to the fact that fluff constantly accumulated there.

If you don’t have a toothpick, you can also use a needle or metal clip. You shouldn’t be afraid that you will break something, but you also need to clean the entrance without unnecessary fanaticism.

NOTE! I repeat once again that it is worth using cotton swabs without the cotton itself, since the tip can get stuck there. Pulling it out is quite difficult. I checked it on my own experience.

After that, turn on the phone and check the sound. If there is still no sound on the iPhone, then try other options.

Why the sound disappeared on the iPhone and shows the headphones: Borodach understands

Hello everyone! Today I ran into a problem. the sound on the iPhone suddenly disappeared. And the sound disappeared quite abruptly. I have an iPhone 6S and often the problem appears on models with a standard 3.5 mm audio input. With frequent use, the headphone jack will become clogged with dust and dirt. As a result, the iPhone thinks that you have connected headphones and is trying to output sound there (often people generally lose sound and write headphones in status).

Models that no longer have a standard ear port usually have a Bluetooth connection or software problem. But you can try to clean the Lighting connector in the same way. If you have already performed standard actions such as restarting the iPhone, then read the article below.

No 3.5mm port

It’s one thing if the sound disappears and shows headphones, but if there is no headphone jack at all, and the sound does not want to appear? First of all, swipe your finger from the bottom up on the home screen to bring up an additional auxiliary menu. Make sure the airplane mode is off. Also see that the “Do not disturb” mode is deactivated (has a month icon). Check that the sound is not at zero.

Go to “Settings”. find the “Sounds” section there.

Here also make sure that the volume slider is not at the bottom. Just in case, move it to the maximum position.

If this does not help or yours was fine, then check that you are not connected to a wireless headset or headphones. Go to the “Bluetooth” section and turn it off.

In the “Settings” go to “General” and at the very bottom open the “Reset” section.

Click “Reset all settings”. you shouldn’t worry that something will be erased, as this will reset the configurations of installed applications. Everything will remain in place and you do not need to make a backup.

Everything seems to be! If you still did not manage to solve the problem, then the breakdown lies deeper and you need to carry the smartphone to a specialist. Write your solutions in the comments if you find them.

Headphone malfunction

If the sound from the speakers works correctly, but when you connect the headphones you do not hear anything (or the sound is extremely poor quality), most likely, in your case, there is a breakdown of the headset itself.

It’s easy to check: just connect any other headphones to the phone that you are sure of working. If there is no sound with them, then you can already think about a hardware malfunction of the iPhone.

System crash

iPhone, like any other device, can malfunction. If there is still no sound on the phone, and none of the methods described above has brought a positive result, you should suspect it is a system failure.

First, try restarting your phone.

Read more: How to restart iPhone
After rebooting, check for sound. If it is absent, you can proceed to heavy artillery, namely, to restore the device. Make sure to create a fresh backup before you start.

Read more: How to back up iPhone
There are two ways to restore iPhone: through the device itself and using iTunes.

What to do if sound disappears on iPhone

Connected devices

iPhone supports wireless devices such as Bluetooth speakers. If a similar gadget was previously connected to the phone, most likely the sound is transmitted to it.

It’s very easy to check this. swipe up from the bottom to open Control Center, and then activate airplane mode (airplane icon). From now on, the connection with wireless devices will be disconnected, which means that you will need to check if there is sound on the iPhone or not.

If the sound appears, open the settings on your phone and go to the “Bluetooth” section. Move this item to inactive position. If necessary, in the same window, you can break the connection with the device broadcasting sound.

Next, call the Control Center again and turn off airplane mode.

Alert settings

Open any application with music or video, start playing the file and use the volume key to set the maximum sound value. If the sound is on, but the phone is silent on incoming calls, most likely you have incorrect notification settings.

To edit the notification parameters, open the settings and go to the “Sounds” section.

In the event that you want to set a clear level of the sound signal, turn off the parameter “Change with the buttons”, and set the desired volume on the line above.

Silent mode

Let’s start with the trivial: if there is no sound on the iPhone on incoming calls or SMS messages, you need to make sure that the silent mode is not activated on it. Pay attention to the left side of the phone: there is a small switch above the volume keys. If the sound is muted, you will see a red mark (shown in the image below). To turn on the sound, just move the switch to the right position.

Why is there no sound on the iPhone

Most of the problems with no sound are usually related to the iPhone settings. In rarer cases, a hardware failure may be the cause.

Hardware failure

The following types of breakdowns can be attributed to a hardware malfunction:

• Inoperability of the headphone jack;
• Sound control buttons malfunction;
• Sound speaker malfunction.

If the phone has been dropped in snow or water before, the speakers are likely to be very quiet or stop functioning altogether. In this case, the device should dry well, after which the sound should work.

In any case, if you suspect a hardware malfunction without proper skills in working with iPhone components, you should not try to open the case yourself. Here you should contact the service center, where competent specialists will perform a full diagnosis and be able to identify, as a result of which the sound on the phone stopped working.

No sound on iPhone is a frustrating but often fixable problem. If you have encountered a similar issue before, please share in the comments how it was resolved.