Connection

The device must be powered from the car itself, or more precisely from a 12V battery. The device itself must be connected so as to receive an image on the monitor, but the installation diagram of the rear view camera is very simple to assemble it with your own hands.

We connect the device with a plus to the car radio. Now you need to find the connector where the wiring is assembled, which is responsible for the license plate light.

DIY Android Auto Raspberry PI Head Unit, Rear View Camera, Navigation & Music

If necessary, the device can be connected to the taillight wiring in the torpedo area. The most important thing is to connect the positive lead, and remember to install the mount for the rear view camera.

Check

After the camera has been installed, it must be checked for functionality. When reverse gear is engaged, the device should turn on automatically.

There are two cases when the display for the rear view camera turned on and everything works, or vice versa. Check which wire you connected to the light.

So everything is working, which means that the installation of the camera was successful and it’s time to lay the wires. This must be done in such a way that it is isolated from moisture and external mechanical damage.

The camera is often supplied with special clips, thanks to which it is necessary to fix the wiring.

Otherwise, carefully route the wiring evenly with the rear light wiring and secure with special cable ties to the other wires.

Installation

So, now it is worth understanding and understanding how the rear view camera is installed. First, you need to choose the right place where to install this device.

Often, this device is put in place of the rear license plate illumination. But first of all, it is necessary to assess the frequency of contamination of the part of the car where the camera will be installed.

Is it possible to install the camera in such a way that it distorts the aesthetics of your car, in addition, what angle do you need?

It is recommended to install it in such a way that the picture on the monitor is as close to reality as possible.

DIY rear view camera. installation and tips for connecting a camera and monitor (130 photos)

Today, most cars are equipped with all sorts of bells and whistles for a more accurate and safe ride. This also includes the rear view camera.

But what if you live in a big city and do not want to hit another car in the parking lot, but you do not have parking sensors. The answer is quite simple and straightforward, the simplest solution is to install a rear-view camera with your own hands.

This procedure will save you money in both cases, because all you need is to purchase this device and mount it on the car. If you are not strong in this, it is quite possible to contact your acquaintances, because almost everyone now has one or more acquaintances who are “familiar” with the car.

Let’s just say, “go to the men at the garage” and ask what and how, because many started with a domestic car. As you know, it is quite difficult to have such a car for a certain time and not understand it at all.

Right choice

The only thing that matters is choosing the right device. Pay attention to the specifications of the camera itself, as certain models are just an add-on to the GPS navigator.

Simple Car Backup Camera. DIY Smart Car (Part 1)

It is also recommended not to buy cheap models, because often for a low price we get a short service life, which means that you will have to pay for quality. By the way, you can ask whether this rear view camera can be repaired.

It is also important to pay attention to such aspects as the operation of the camera in the dark, the angle of view, the presence of parking markings, the protection of optics from the influence of external factors.

Wireless Cameras

Progress does not stand still, which means automotive technologies will also develop, recently wireless rear-view cameras have become popular. A huge advantage of such a device is the ease of installation, since there are no wires and all that is needed is to turn on Bluetooth on the camera and car radio, so that the radio display shows the image from the camera.

But do not praise such devices, they appeared on the market not so long ago, and will not be able to ensure stable operation of the camera for a long time.

Installation

You have to decide where exactly the camera will be mounted. Installation methods:

• in the plafond of the regular license plate lighting. Many manufacturers make transition glasses that allow you to install the camera and keep the room backlight. If a parking assistant is installed on your car model in certain trim levels, then you just need to purchase such a lamp cover. At the same time, you can pick up a device even among universal accessories;
• into the trunk opening handle, which is often made in a single body with a plastic molding above the license plate. The camera in a rectangular body can be easily fixed with ordinary screws;
• attach to the license plate frame;
• fit into the bumper. On some cars, you don’t even need to remove the bumper for installation. For such installation, cameras made in an oval body are suitable. You just need to make a hole in the bumper. For greater reliability, from the inside, the body must be placed on a body sealant or sealed with a glue gun. Wires can be routed to the interior of the car through the ventilation holes located in the luggage compartment.

Electronic component

Consider wiring carefully. The joints must be properly insulated. To prevent the wires from dangling or fraying, wrap them with cloth tape, if possible, fasten them with ties to the standard wiring harnesses, or fix them using the technical holes of the body elements. In the cabin, the wires can be pulled both below along the thresholds and behind the headliner.

Installing a rear-view camera with your own hands will not cause difficulties even for a novice car enthusiast, but you need to approach the connection much more thoroughly. It makes no sense to consider the rear-view cameras that come with a special mirror. You just need to connect everything according to the instructions that are necessarily attached to the device.

For the normal functioning of the system, it is used:

• two-wire cable for powering the camera;
• two-wire video communication wire. To transmit video to the monitor, wires with RCA connectors (known to everyone as “tulips”) are used. The conductors are not shielded, therefore, if necessary, they can be lengthened or cut for pulling in hard-to-reach places. In some variants, for the correct operation of the system, an additional excitation wire will come out of the RCA connector.

The excitation wire activates the screen of the radio with a “positive” current, forcing the system to automatically switch to the mode of broadcasting the image from the camera. The excitation wire is not required for all multimedia systems; in some devices, the automatic transition to the rear-view camera is carried out via the video link. If such a function is not provided by the radio tape recorder or the device is not connected correctly, then you will have to change the image on the screen manually by pressing a special button.

Optional equipment

One of the main problems is throwing dirt and ice on the lens. Even a few standard systems are equipped with such a useful function as camera washing. If you are installing an accessory in the trunk lid of a car that has a rear window washer, cleaning is very easy. You just need a tee that will be implanted into the standard washer line in front of the rear window nozzle. As a spray, you can take a compact nozzle from any suitable car. Since the lens glass is small, there is no point in using a fan nozzle.

The second useful feature is the camera illumination, which in some models is built into the body. It should be admitted that in most cases the harm from this function is much more than the benefits. The backlight illuminates the camera lens, and as a result, the image quality does not improve at night. A glare problem can arise if a rear view camera is installed next to the license plate light. In this case, replacing incandescent bulbs with LEDs can help. If this move does not solve the problem, you will have to tinker with the protective screen.

Installation options

There are several ways to equip a car with a rear view camera (review of popular models):

• a separate camera that connects to a standard multimedia system or a self-installed screen;
• a set of cameras with a rear-view mirror, on which the image will be displayed when moving back. It can be either a separate mirror or an overhead panel that will be mounted on top of a standard reflector.

Connection and installation of a rear view camera

Isn’t a camera a great way to make parking in tight spaces easier? Do-it-yourself installation of a rear view camera will not take you much time. Consider the installation of a mirror with a built-in camera, as well as diagrams for connecting an external device to a monitor of a multimedia system.

Connection methods

The rear view camera and the car monitor can be linked wirelessly. This requires a special module. The power supply of the module is connected to the reversing lamp, and from the module it goes to the camera. The second wireless module is connected to the monitor power supply. The disadvantage of this method is the interference, which often prevents the normal transmission of the image. Also, this method is not suitable for radio tape recorders that need an excitation wire.

Let’s take a closer look at the classic connection option. The essence of the above diagram is to connect the camera power to the reversing lamp, the voltage at the terminals of which appears only after turning on the reverse gear. The connector (“tulip”) is connected to a standard output on a radio tape recorder or a screen designed for video communication. The field wire must be connected to the radio output, usually labeled “Reverse”. You can find out whether an excitation wire is required for your multimedia system from the technical documentation for the radio tape recorder. On this, the installation and connection with your own hands for most cars can be considered complete.

Fault monitoring system lamp

What if you have installed a rear view camera in your car and it only works when the car is muted? In many modern cars, usually with German roots, a lamp health monitoring system is installed. The PWM controller sends rectangular positive pulses along the power wires to the lighting fixtures, which helps to detect burnout of the rear lights. Since the lamps have inertia, current ripple does not affect their operation. But the reversing camera will not work correctly with such interference.

To prevent such an effect, the camera must be connected to the reversing lamp through a relay powered by a cigarette lighter (there the current will already be constant). In this case, the “” from the ZX lamps to the relay winding must be applied only after rectification by a diode and smoothing of the ripple by a capacitor. The “minus” for powering the camera must be taken as far as possible after the “mass” of the ZX lamps.

We offer you to watch a video with a detailed description of the method of eliminating interference, so that you are guaranteed not to have problems with the picture on your car.

Connecting the camera to the radio (car radio display)

The camcorder can only be connected to radio tape recorders with a liquid crystal display of at least 3. 4 inches. Smaller monitors will not provide the desired picture quality. The free connector of the video cable is connected to a special output of the head unit (for searching, refer to the instructions for the radio). If such an output is not provided, it is possible to connect to the output marked VIDEO IN. If the jacks and plugs do not match, you will need to purchase an adapter.

You can see in detail how to connect a rear view camera to a radio tape recorder at

After connecting the camera to the liquid crystal display of a high-quality car radio, a “picture” of decent quality is issued.

The image clearly shows the “mirror” effect during the operation of the video camera, to which it is easy to get used to after several days of using the parking sensors.

To get used to the scale, you can go out and consider the real distance between cars, estimate the gap remaining to the obstacle.

Connecting the camcorder to the navigator and navigation devices

Connecting a rear camera without its own monitor to the navigator is logical. Without cluttering up the “torpedo” or the center console with an extra screen, you use the already familiar installed device. Questions on how to connect a rear view camera to a navigator do not arise when buying a device for which such an opportunity is planned.

The packaging of such navigators indicates the possibility of connecting a video camera, the instructions describe the necessary user actions when connecting. The set of the navigator may include adapters for connectors of popular models of video cameras.

If the rear view camera is already installed, the car enthusiast only needs to plug the plug from the video camera into the desired connector.

In the absence of a standard connection of the camcorder, you need to purchase additional cables, plugs, and a special adapter. The schematic diagram of the power supply from the rear light, the wiring to the projection device does not change.

An adapter from RCA to the input to the navigator (it is often called a “tulip” in everyday life) is needed only if there is no AVI input. For navigators equipped with such an input, a standard video cable connector is often suitable.

Rear view camera selection

Miniature rear view cameras should not be confused with optical sensors.

Mounting the camera becomes the first mounting operation, regardless of the choice of the projection device. There are several important points to consider when choosing a camera:

• Viewing angle. A viewing angle of 110. 120 degrees is considered normal. Drivers choosing cameras with a wide angle of view (up to 180 degrees) can better assess the traffic situation, but must take into account the panoramic effect, which distorts the actual size of the image.
• Resolution and sensitivity. The standard resolution of 628 x 582 pixels suits most ordinary drivers, increasing the image quality for the rear packing video camera does not make sense. When choosing a color sensor (CCD or CMOS), you need to take into account that CCD transmits a better image, balances colors, but is much more expensive. CMOS sensors perform worse in low light, provide acceptable color quality in daylight.
• Infrared illumination. Additional illumination with sufficient light provides better color image quality. In low light, an infrared source allows you to see the road from behind in black and white at a distance of up to five meters.
• Video image format. Choosing from three formats that the camera can be equipped with (SECAM, NTSC, PAL), you need from Honor what type of monitor the video image will be displayed on. Mismatching formats will make the purchase and installation of the camera meaningless.
• Signal transmission method. Dividing cameras into wired and wireless affects cost and connectivity. Wired camcorders are versatile and can be connected to all types of monitors. Cameras equipped with transmitting and receiving modules can often transmit images only to the navigator.
• Complete set with cables. It is preferable that the camera is equipped with a three-wire video cable with an additional excitation wire, the power wire can be two-wire. The length of the cables also matters. The standard length (2-3 meters for the video cable, one meter for the power cable) may not be enough to connect the camera in your car model.
• Body material. Experienced car enthusiasts choose cameras in a metal case, considering it to be more durable and durable than a plastic one.
• Installation site variability. There are cameras mounted in the license plate frame, devices in a separate case. A separate video camera assumes the choice of several installation locations that are convenient for the driver.

The rest of the standards of video cameras (presence of parking lines, supply voltage, protection from dirt) are the same for most models.

Many car enthusiasts consider the most convenient rear-view cameras, complete with a monitor mounted in the rear-view mirror.

It is difficult to deny the convenience of such a device. The monitor turns on when the reverse movement starts, it allows you to see the traffic situation in good resolution. The main disadvantage of such gadgets is the high price, which is inaccessible to many categories of motorists.

Less convenient reversing camera, complete with foldable miniature display that can be placed on the dashboard

The main disadvantage of such devices is the obstruction of the view, especially if a video recorder, a navigator, and a separate radar detector are already installed in the car. Car enthusiasts find it more practical to use the display of one of the existing devices. If you buy any type of rear view camera (with or without a monitor), you need to install it in the back of the car.

Connecting a rear view camera with your own hands to a radio tape recorder, a tablet and a navigator

In budget cars, a standard rear-view camera is rarely provided for basic configurations. often than not, automakers offer it as an expensive add-on option. Many Russian car enthusiasts buy a separate rear view camera and install it themselves. To do this, you do not need to radically modernize the electrical wiring of the car. Connecting a rear view camera with your own hands requires basic wiring skills, experience in disassembling several elements of the interior and body. Installation of the camera will improve the conditions for safe parking, road monitoring in difficult traffic traffic

Practical operations for installing a camcorder

We are not considering installing a camera behind the rear window of a car. With this installation, the camera glares, does not allow you to see nearby obstacles from behind. Do not be afraid of vandalism, a camera with torn wires is not of interest to buyers, but it is better to disguise it in the rear bumper or under the trunk lid.

If the camera is mounted in the license plate frame, you have no other installation options. When choosing a location, most experienced mechanics find it more convenient to install the camera above the license plate, at an angle to the road surface.

In any case, to install the camera you will need:

• install the video camera in the intended place;
• connect the camera power;
• bring the video cable to the front of the car;
• connect the video cable to the monitor to transmit the image.

The steps for installing a video camera depend on your car model (sedan, hatchback, crossover) and the installation location. To do this, you can use the existing holes in the bumper, the fifth door cover, or cut new installation positions. It may be necessary to dismantle the bumper, install additional brackets on the inside of the body part for attaching a video camera (metal plates).

Most experts consider the most convenient way to power a video camera by connecting the power cable to the left rear lamp. This may require disassembling the trunk sill, the left side of the trim. Having disconnected the rear light block, you need to find the power supply contact with a multimeter (with the rear light on).

Most camcorder models have three outgoing wires marked with colors. For the positive power wire, red is used, for the negative one. black. The yellow mark indicates the video cable. The red wire is connected to the contact of the lamp, the black one is closed to the car body. It will not be superfluous to provide the positive wire with an additional fuse (0.5. 1A) in the circuit.

The easiest way to lay the video cable is to mount it on the left side of the passenger compartment under the removed sills and floor trim. You can use special tape or plastic clips to secure the cable. All installation operations end with the installation of the removed body and interior elements in their regular places. It is necessary to finally fix the screws and clips of the casing only after testing the operation of the camera, making sure that it is working properly.

For novice car enthusiasts, the greatest difficulty is connecting the video cable to an available monitor. Most owners of budget versions of cars consider the most convenient way to connect the camera to the display of the car radio.

Connecting rear view camera to tablet and mobile electronic gadgets

Of all types of electronic wearable devices (laptops, smartphones), the tablet is the most convenient for connecting a rear video camera. The size of the monitor screen, the quality of the resolution is suitable for work. The flat design of the tablet allows you to choose several options for convenient installation.

Often, owners of cars with a primitive radio tape recorder, without a navigator, have no choice but to connect a rear-view camera to a tablet. To connect a wired video camera, you will need to purchase a TV tuner (it looks like a USB flash drive) with a plug for video input.

On the Internet, it is easy to find designs of homemade tripods for tablets that make it easy to mount and remove a mobile device on a dashboard or center console. For small tablets, you can arrange a special slot on the back of the sun visor.

For tablets with the “Android” operating system, it is necessary that the camcorder model be adapted to the “operating system”, the tablet must be equipped with a USB port. In some cases, additional software installation will be required.

A properly installed and connected rear-view camera will provide a better view compared to the view from the side mirrors and salon mirrors, remove blind spots, show stumps, parking posts, pits in the asphalt.

Installing a parking or panoramic rear view camera, without requiring much effort, improves the safety of parking and reversing. If you do not have the skills of independent work with a car, connecting electronic devices, you need to contact experienced specialists to install the camera.

Easy installation of a rear view camera on a car with your own hands. And again Kia RIO

Greetings, dear readers! Now we will continue to experiment with the installation of additional equipment in a passenger car. And the topic of the article will sound like this: do-it-yourself installation of a rear-view camera on a car.

precisely, we will be installing a universal camera that fits all brands of cars on a small Kia RIO of the author of the blog. I think that this direction will be of interest to many lovers of comfort while driving.

So, let’s say right away that our camera is not a model one and it can be installed, if desired, even on a tractor. The second point, which must be said, is that it was not purchased separately, but came complete with a mirror based on Android, which was discussed in great detail here.

The indisputable advantage of just such a non-model peephole is that it can be placed exactly in the center of the rear of the car. This arrangement, in contrast to the shade, allows you to make the camera’s viewing angle more uniform. But on the other hand, it is more accessible to vandals.

In general, in this moment, everyone must draw their own conclusions for themselves, but we immediately proceed to demonstrate the operation of the entire system:

And it all works as follows. When you turn on the reverse gear, a picture from the back of the car with parking markings is automatically displayed on the mirror screen:

A big plus is the fact that when reversing, the built-in LED illumination lights up on the machine:

In normal mode (when moving forward), the DVR application constantly writes an image from it, which can always be viewed on the mirror display:

Now with regard to the sensational question of the dust and moisture protection of such a camera from the Middle Kingdom. Well, what can I say at the moment, based on my personal experience of operating it?

It was installed at the end of autumn 2015. As you well saw, this peephole is located on the outside of the car. As of this writing, no issues have been reported. Only wiped dust off a couple of times.

Therefore, God forbid, that everything will continue to work so well and bring pleasure to its owner. The only thing that immediately did not like in the mirror as a whole was the crooked translation of the programs. But we have already fixed this:

In general, my friends, let’s move on to the very installation of a rear-view camera with our own hands on our experimental car. Let me remind you once again that he is the kid Kia RIO in the hatchback body.

So, the whole process begins with the obligatory partial disassembly of the luggage compartment. There you need to remove the casing near the castle, and also remove the polic itself:

And here comes the first important point. In the picture above, note the circled wire harness. Remember its location, it is through it that we will lead the wires from the camera itself. This is how it looks:

Now we unscrew the license plate and see such wonderful holes in the bumper:

I think that now the further course of events has become clear to you. We take the wires from the camera and carefully pass them through the mounting frame of the number. Then we run them into these holes, and then we put them into the trunk through the plug:

The picture above is a top view. Look carefully at what you should end up with. Naturally, after all the manipulations, we again squeeze the entire wiring harness well so that moisture does not penetrate into the trunk.

Now we need to remove the left side trim. To do this, unscrew all the screws at the bottom:

And then gently pull the panel itself towards you:

Now watch closely. In the space that opens, we will see a block with wiring (picture above). So, the red wire from our rear view camera needs to be connected to the white-orange wire in this block.

To do this, we disconnect the block itself and insert the red one into the pin with the yellow-orange wire. After that, we snap the block again. As you can see, there is no soldering, which means there is no loss of warranty:

Thus, we apply voltage from the plus of the reversing light, so that the image is automatically displayed on the mirror display when the reverse gear is turned on.

But then everything is much simpler. Under the same panel, we start the wires from the camera to the area of ​​the rear left door, remove the sealing rubber band between the ceiling and the trim, and lead the entire harness to the front pillar. Here’s a general outline:

I will repeat once again that it is not necessary to disassemble anything in the cabin at all. Just remove the sealing gum and that’s it. And already in the bow, you need to remove the front pillar trim in order to run a wire under it:

Once again, it is worth saying that you need to be careful when removing the skin, since it is attached to a kind of shock absorber, which does not allow it to be completely removed.

Therefore, gently pull only the very top at a 90 degree angle:

Then we hide the tourniquet under the ceiling and bring it to the mirror itself. To get rid of the rest of the wires, I recommend removing the lighting shade and packing everything discreetly in the opened space:

Well, friends, on this our simple installation of a rear-view camera on a car with our own hands came to an end. As you can see, there is nothing complicated and very clever in this process. Everything turned out to be very simple.

But if you have any questions, then ask them in the comments. We will work together to solve your problems. And now I propose to laugh a little with cool eccentrics.

Which reversing camera to choose ?

The answer to this question will be individual for everyone. Everything will depend on what you have and what you want. So the simplest reversing cameras cost about 50. Of course, they will also help you when parking your car, but we would like to tell you about what you will be offered for a lot of money.
First, I would like to say about the camera resolution. So almost all, even the cheapest camera options, guarantee the proper resolution, which is quite comfortable for viewing.
Second, and more importantly, the camera must have good sensitivity. In fact, this is the ability of the reversing camera to work in low light conditions. So, cameras are produced that work only in sepia (b / w) mode, which allows you to make the camera more sensitive, just for work at night.
Thirdly, the angle of view of the camera. So it starts from 120 degrees and goes up to 180 degrees. Of course, with a wider viewing angle, you are able to monitor a larger area when parking, which will guarantee you safer reversing. But, with an excessively large view, a “panoramic effect” appears, which does not correspond to ordinary perception, which may seem inconvenient to many.
Fourth, the method of mounting the camera. So the cameras can be made separately or built in, for example, in a frame under the state registration plate.
Fifthly, if you already have a multimedia recorder (with an LCD screen), then you most likely will not need to take a monitor to display the picture from the camera. If you do not have such a radio tape recorder, and you do not plan to install it, then you will have to take the rear view camera with your own LCD monitor.

Installing a rear view camera with your own hands

In one of our articles, (“How to install parking sensors with your own hands”), we have already talked about devices for controlling the rear of the car during parking. But this option may seem to someone not visual and, as a consequence, not effective. Indeed, if a thin column is located between the sensors, then its determination with the help of a parking sensor becomes problematic. It is much clearer to observe the full picture of what is happening through the rear view camera when you park in reverse.
How to install and connect a reversing camera in order to have such objective visual information, we will talk in this article.

Do-it-yourself installation of a rear view camera

And so, in our case, the simplest rear-view camera of the RM116B model is taken. Camera viewing angle 120 degrees. Mounting the camera on the back of the car will be a top priority. It is necessary that the rear view camera is in the middle, covering the parking area to the left and right as much as possible. If you push it in, then its edges may be “cut off” by the bumper.
But you shouldn’t expose the camera unnecessarily. In this case, the camera will get too dirty from flying splashes of dirt, in addition, in our country there are still many vandals who just look where and what can be “pulled”, even if they don’t really need it.
In our case, the camera was placed on the frame of the rear license plate light.

The frame with the shades is removed from the bumper. The place of attachment of the rear-view camera is shown.

Rear view camera already installed in place. (a distance plate was placed under the camera so that its peephole protruded from behind the bumper)

If you move a little away from the car, the camera is almost completely invisible.
Power and video signal wires, from the rear view camera, are pulled into the luggage compartment, through any plug, in the area of ​​the spare wheel / rear bumper

The camera can be powered from the reversing lamp power cord. In this case, the easiest way is to disconnect the block going to the rear headlight, and sorting through the contacts, find which one is powered when the reverse gear is on.

Next, connect to this wire with a clip (see the article “Connecting to the wiring in the car”) In our case, this is a red-white wire or green-white, one to the block, the other after it.
Now we pull the wiring to the radio / monitor located in front of the instrument panel. As a rule, the wiring is pulled along the left side, dismantling the sills and laying the wires under the carpet of the passenger compartment.
After you have pulled the wires to the front of the car, we start looking for power (if you have a monitor, you don’t need to do this for the radio) and search for power for the reversing light. If you do not want to look for power for the reversing light in front, you can, together with the video signal wire at the back, route it back to the dashboard, or at least trace where it comes from the dashboard, and connect already in front.
As a result, we get the following power connection diagram and all control signals when the rear view camera is operating.

The results of the rear view camera after do-it-yourself installation

Example 1
Picture from the rear view camera on the monitor

Example 2
Picture from the rear view camera on the monitor

Example 3
Picture from the rear view camera on the monitor

The examples given show how much more comfortable and visual it has become to park a car, even with one of the simplest cameras. Perhaps the above result will be the final motivation for someone in order to still install a rear view camera on your car.

What to look for

Before you buy a rear view camera, you should pay special attention to the characteristics of the product. After all, some of them may only be an addition to the GPS navigator. If the device will be used very often and for a long period, you should not try to save money on such accessories. As a rule, poor quality is hidden behind a relatively low cost.

When choosing an accessory, you should pay special attention to its characteristics:

• Black and white or color photography.
• Does it work at night.
• What viewing angles does.
• Are there parking markings.
• Is there a moisture protection for the lens, and what material is the camera made of?
• Video Resolution.

Where to mount

Installing a rear view camera usually starts with choosing a location. Installation of such accessories is usually carried out in the license plate lamp located at the back. There are kits that are equipped with special shades with a place specially designed for the camera. Before deciding where the accessory will be installed, it is worth answering a few questions:

• How often does this part of the vehicle get dirty? For example, it is allowed to install a rear view camera on trucks directly on the roof. In this case, the accessory is protected from dirt, but at the same time it will be much more difficult to wipe it.
• What is your priority shooting angle? Tilting the camera allows you to see those areas that are difficult to see in the mirrors. But at the same time, experts recommend choosing a mounting location so that all objects on the monitor look more natural.
• Is it possible to install the device so that it is not visible to prying eyes and does not spoil the appearance of the car?

Installing a rear view camera,, may cause some difficulties. If you doubt your own abilities, then you should seek help from specialists.

Rear view camera installation: connection

The camera must be powered from the vehicle’s mains. They consume such accessories for about 12 V. Finding a wire with this voltage will not be difficult. But at the same time, you will have to dismantle all the parts that do not allow you to get to the desired cable, which leads exactly to the license plate illumination. As a rule, in such situations, it is necessary to remove the trim and sills made of plastic in the trunk, which hide the wiring coming from the car radio. The camera must be connected to it so that you can get an image already on the monitor. In fact, the installation diagram of the rear view camera is quite simple and straightforward. Installation does not cause any particular difficulties.

The camera is connected to the plus cable and the radio connector. Of course, the part will need to be removed. Then you need to find the connector where all the wires are collected, thanks to which the license plate illumination is carried out. This is not always required. This is only necessary in cases where the installation of a rear-view camera, the price of which depends on many characteristics, is carried out in the backlight. If desired, the accessory can be connected to the wires of the reversing lights, in the area of ​​the torpedo. The main thing is that the wire is positively charged to power the camera.

Do-it-yourself installation of a rear view camera

Modern passenger car models are equipped with parking sensors. Therefore, many drivers believe that installing a rear view camera is a waste of money. After all, the manufacturer has already taken care of safety. However, such equipment allows you to avoid unpleasant situations. After another collision with a post or a tree while parking, many car owners begin to think about purchasing such a useful accessory. In fact, installing a rear view camera is a simple process. You can do it yourself. The main thing is to choose the right accessory.

Final stage

After connecting the camera, you should check its operation. When engaging reverse gear, the device should automatically turn on. If an image appears, then everything is connected correctly. It remains to lay the wires. and the installation of the original rear view camera will be completed. There is nothing complicated in this matter. It takes a little patience and neatness here.

It is worth laying the wiring so that it is protected from moisture and mechanical damage. To do this, you should use your own clips and lay the cables only in those places that are provided in the vehicle for such purposes.