See how we change glass in 9 steps

Glass can only be replaced at the office. This requires a separator, an anti-dust room, a cryogenic chamber with a temperature of 200 ºС and a vacuum press with a pressure of 5 atmospheres.

But on the road, we can replace the entire display, along with the glass: we will install a new one and take the old one. In this case, you pay only for glass replacement. 3,500 rubles.

Examples of Samsung Galaxy A50 A505 2019 displays where only glass is broken

Samsung Galaxy A50 Screen Replacement

How to replace display on Samsung Galaxy A50

In this article, we’ll show you how to replace the display on your Samsung Galaxy A50 smartphone yourself.

The Galaxy A50, equipped with an AMOLED screen, did not survive the fall. Module replacement required. We will install a spare part of original quality assembled with a middle body part. The display itself was bought here.

For all the external deceit, the back cover of the Galaxy A50 is made of plastic, you can even do without preheating and confine yourself to a spatula for parsing.

In the lower part, create a gap with the narrowest part of the blade and, slightly bending to the side, peel off the back cover. If necessary, you can add a small amount of isopropyl alcohol to the spatula to reduce the stickiness of the factory tape. Only after that we remove the SIM-tray.

Remove the remaining adhesive tape on the frame and lid, then replace it with a new one.

change, screen, samsung

Samsung A50 Screen Replacement

The plastic frame is fixed with screws from the bottom and top, we use a screwdriver and get rid of the fasteners.

With the same spatula for parsing, pry the frame and snap it off. We work carefully: the frame is thin and can crack from excessive bending.

We apply the first parsing rule: disconnect the battery first.

We will prepare the phone for connecting and checking a new spare part. It will be enough for us to disconnect the display cable from the lower subboard.

change, screen, samsung

We connect the ribbon cable to the new display module, make sure it is tight. We connect the battery cable back and you can start the device.

Since the contacts and the power button itself remained on the middle frame, we will turn on the phone by closing the contacts. There are two of them. Use any metal tool.

After starting, we check the operation of the sensor and the image quality. We make sure that there are no flares, graphic distortions and incorrect color reproduction.

The sensor can be checked in two ways:

Using all the controls of the software shell (curtains, buttons, icons, brightness sliders and side gestures, if any) and dragging any application icon on the desktop across the entire area;

Turning on the special display mode of touching the touch screen:

  • Settings app
  • item “About phone / About device”
  • repeated clicking on the line “Build number”, until a message appears about the inclusion of developer mode
  • return to the main settings screen
  • scroll down and find the “For Developers” item that appears, go to it (on various devices, this menu item can be hidden in “Accessibility”, “Additional Settings”, “System Settings”, etc.)
  • turn on the item “For Developers” and look at the bottom of the section “Input”, “Display touches” and voila. the finger is followed by a coordinate grid leaving the line of touch, which allows you to fully check the touchscreen for serviceability and eliminate false and phantom clicks

The part has been checked and must be installed, which means it’s time to transfer the board and peripherals to a new frame. Disconnect the board-to-board cables and unscrew the screw that secures the motherboard. We also disconnect the antenna cables and remove them from the channel.

At the bottom, we have to unscrew and disable the sub-screen fingerprint scanner, antenna contacts and the sub-board itself along with antenna cables.

There is no need to carry the thermal bands, our new original module comes with a full set of rubber bands and a thermal interface.

The speaker and vibration motor remained under the main board. Gently pry with tweezers and transfer to a new place.

Be careful when removing the Fingerprint Scanner, if the scanning window is dirty or damaged, it could cause it to malfunction.

The antenna contact and the bottom board are fixed on double-sided tape, pry off with a spatula.

The last in line is the rechargeable battery. In this model, Samsung did not provide any labels to facilitate dismantling the battery, tightly gluing it on both sides to the metal frame.

To loosen the tape, add alcohol around the edges, in the gap between the battery itself and the frame. Leave it to “wet” for a couple of minutes and easily peel off the battery.

We will install the battery on acrylic double-sided tape. Two stripes around the edges are enough.

We remove all protective films from rubber bands and thermal pads and assemble the phone in the reverse order.

The final step will be to install the back cover. Here again, acrylic tape will help us. We glue it along the edges of the frame, cutting off the excess with a scalpel or office knife.

REPAIR Samsung A50

Advantages of contacting a service center

  • close location to the metro and free parking;
  • a wide range of services;
  • repairable Samsung Galaxy A50;
  • individual approach and quick solution to any issue;
  • the possibility of repairs on credit and installments.

Galaxy A50 common problems

Repairing Samsung Galaxy A50 is a tricky business, don’t try to fix it yourself! Contact the masters!

Most often, the specialists of the official Samsung service are contacted with the following problems:

  • replacement of the display (screen);
  • replacement of the storage battery (joint stock bank);
  • speaker replacement;
  • rear cover replacement;
  • repair or replacement of power connectors and headphone jacks;
  • cleaning the smartphone after flooding;
  • software installation or flashing.

Samsung A50 Repair

Samsung repair service center is ready to offer services for the elimination of breakdowns of any level of complexity. The cost of repairing and replacing parts Samsung Galaxy A50 is lower than elsewhere.

Samsung A50 repair service addresses

All services are provided with a corporate guarantee. There are always promotions and special offers for clients. Contact us and we will help you eliminate any malfunction.

Glass replacement and other services

Need sound tweaks, battery recovery or display repair on your Samsung Galaxy A50 or Samsung Galaxy A40? You can find out the cost of such services from the price list, by phone or online chat. Please contact. High-quality service and affordable cost of services are guaranteed.

Repair Samsung Galaxy A50 (A505)

High quality copy. Warranty 2 months.

Paid in case of refusal to repair.

Urgent repair of Samsung Galaxy A50 (A505)

The bezel-less Infinity-U display and premium case design make the Samsung Galaxy A50 attractive to many Ukrainians. The Super AMOLED touchscreen gadget is ideal for vlogs, live broadcasts and work conferences. However, the device is not protected from drops, water ingress under the case and various damage.

Most often, the owners of Samsung Galaxy A50 contact a service center in Kiev because of problems with the screen. You can learn more about them in the article Stripes and spots appeared on the Samsung Galaxy display. HelloService engineers will diagnose such a device and fix all faults in a couple of hours.

Samsung Galaxy A50 A505 Screen Repair and Replacement Services

The chips and components used in the assembly of the Samsung Galaxy A50 are reliable. But when exposed to moisture, dust and careless handling, the charging connector becomes unusable. As a result, the phone won’t charge. Please contact Samsung HelloService to resolve this issue and have your speakers, microphone, and buttons repaired. In our SC, your problem will be solved as soon as possible.

Samsung Galaxy A50 Lcd Screen Replacement

Also, our service center in Kiev is contacted, if necessary:

  • repair and replacement of the camera module;
  • battery replacement;
  • glass replacement;
  • replacing a broken sensor or repairing a Samsung screen;
  • repair and replacement of a Wi-Fi receiver;
  • replacement of the camera glass;
  • cover replacement;
  • repair and replacement of the motherboard;

Frequently Asked Questions

Parts warranty from 3 to 12 months, depending on the type of part. For work on repairing boards, a warranty of up to 2 months.

The repair time depends on the availability of spare parts and on the complexity of the work. In most cases, if parts are available, repair takes up to 2 hours, board repair takes up to 1 day. You can find out the availability of details and exact dates from the manager of the department.

Yes, all shown include the cost of parts and labor.