BIOS does not see the USB flash drive

Perhaps the most common problem with booting from a USB drive. We already have an article about this problem and its solutions, so first of all we recommend that you be guided by it. However, on some laptop models (for example, ASUS X55A) there are settings in the BIOS that need to be disabled. This is done like this.

  • We go into the BIOS. Go to the “Security” tab, go to the “Secure Boot Control” item and disable it by selecting “Disabled”. To save the settings, press the F10 key and restart the laptop.
  • Boot into BIOS again, but this time select the “Boot” tab. In it we find the “Launch CSM” option and enable it (the “Enabled” position). Press F10 again and restart the laptop. After these actions, the flash drive should be correctly recognized.

The second reason for the problem is typical for flash drives with recorded Windows 7. this is an incorrect partitioning scheme. For a long time, the MBR format was the main one, but with the release of Windows 8, GPT took the dominant position. To deal with the problem, overwrite your flash drive with the Rufus program, choosing in the “Scheme and type of system interface” option “MBR for computers with BIOS or UEFI”, and set the file system to “FAT32”.

The third reason is problems with the USB port or the flash drive itself. Check the connector first. connect the drive to a different port. If the problem is observed, check the USB flash drive by inserting it into a known working connector on another device.

Booting from a USB flash drive on ASUS laptops

ASUS notebooks have gained popularity for their quality and reliability. Devices from this manufacturer, like many others, support booting from external media such as flash drives. Today we will consider this procedure in detail, as well as get acquainted with possible problems and their solutions.

Solving Potential Problems

Alas, the boot process from a USB flash drive on an ASUS laptop is far from always successful. Let’s analyze the most common problems.

Booting ASUS laptops from a USB stick

In general terms, the algorithm repeats the method identical for all, but there are also several nuances, which we will get acquainted with later.

    Of course, you need the bootable USB stick itself. The methods for creating such a drive are described below.

Read more: Instructions for creating a multi-boot USB and bootable USB flash drive with Windows and Ubuntu

Please note that at this stage, the problems described below in the corresponding section of the article most often occur.!

Read more: BIOS setup on ASUS notebooks

  • This is followed by directly booting from an external USB drive. Provided that you did everything correctly in the previous step, and did not encounter problems, your laptop should boot correctly.
  • In case there are problems, read below.

    Touchpad and keyboard do not work during boot from a flash drive

    This is an uncommon problem in most recent laptops. Its solution is absurdly simple. connect external control devices to free USB connectors.

    As a result, we note that in most cases, the boot process from flash drives on ASUS laptops runs smoothly, and the problems mentioned above are rather an exception to the rule.

    How to boot from a USB flash drive ASUS laptop with UEFI BIOS

    How to boot an ASUS laptop from a USB flash drive with UEFI BIOS BIOS Utility. EZ Mode

    asus, laptop, install, windows, flash, drive

    The other day they brought me an ASUS X541N laptop. They asked me to install Windows 10 or Windows 7. I have a multiboot flash drive with different versions of operating systems, which I made a couple of years ago. I stuck this USB flash drive into the laptop, turned it on and began to press the Esc key on the keyboard. I thought I could quickly manage the Windows installation, but it didn’t work.

    After pressing the Esc key, a window appeared asking you to select a boot device. But my flash drive was not on the list. only the laptop’s hard drive was present. I went to the “Enter Setup” item in this window. Before me on the screen appeared the modern UEFI BIOS of the ASUS laptop. BIOS Utility. EZ Mode:

    over, in the UEFI BIOS, my flash drive was displayed in the “USB Port” section, but it was not in the “Boot Priority” section. This meant that I could not select it as a boot device and install Windows from it.

    Then I decided to try changing the BIOS settings. I had done this before with a Lenovo laptop (that also had a UEFI BIOS). I will say right away: if it helped in the situation with Lenovo, then it was with this ASUS laptop that changing the settings did not work:

    I switched to “Advance Mode”. in the Security section I disabled the secure boot protocol (set the Secure Boot Control parameter to Disabled):

    Further, in the Boot section, I disabled the Fast Boot option: Then I saved the changes and rebooted. After rebooting, I entered BIOS again in the Boot section.

    But in this section there was no and did not appear the “Launch CSM” option (and no other similar, for example: “CSM”, “CSM Boot”, “CSM OS”, “Legacy BIOS”). In other ASUS laptop models, after activating this option in the Boot section, it became possible to boot from a USB flash drive.

    And now I’ll tell you how I solved this problem and still installed Windows on an ASUS laptop:

    Modern laptops have UEFI BIOS. In order to boot without problems from a USB flash drive in UEFI mode and install Windows on a GPT disk. this flash drive must be formatted in the FAT32 file system.

    I inserted my flash drive into another computer. I went to its “Properties” and saw that it was formatted in the NTFS file system:

    Then I just cleaned it up and recreated the bootable Windows USB stick in the FAT32 file system.

    After that, I reinserted it into my ASUS laptop. turned it on. pressed the Esc key on my keyboard several times. A window appeared with a proposal to choose a boot device. and this time, in addition to the laptop’s hard drive, there was also my flash drive. I selected it and started installing Windows. I didn’t even have to go into the BIOS and change something there.

    • Installing Windows 7 second system after Windows XP
    • Windows 7 installation instructions
    • How to reduce the scale of the screen on a computer: 5 common schemes 3 additional instructions
    • Error while installing Windows on laptop: “The selected disk has a GPT partition style”
    • 4 steps to connect a webcam to your computer
    • 3 options to open a SIG file with the right to correct
    • How to install Windows 7 on a new hard drive
    • Instructions for installing Windows 98. Part 2

    I want to install Windows 7 on a laptop GPT disk. BIOS. UEFI. But nothing comes of it. during installation, the laptop freezes at the Windows logo and nothing happens further.

    To install Windows 7 in UEFI mode on a GPT disk. first disable the Secure Boot (Secure Boot Protocol) option in BIOS.

    Disabled Secure Boot. it did not help. What else do you recommend?

    Then I would advise you to switch to Legacy mode in BIOS (or CSM. depending on which laptop), and then convert the hard drive to MBR format.

    why bother installing a 7 on a gpt disk? then I would put ten

    Windows 7 flash drive in fat32 but it didn’t help. Security Boot is disabled, Fast Boot is also disabled. And things are still there.

    tell me please, does not want to start from a flash drive either. Issues 0xc000000d and swears at the boot file in the efi directory

    Hello, tell me, I really want to put the seven on my ASUS fx505gm

    It was 2018, and I was already the third day, excuse the expression, I was fucking with a laptop in the hope that right now this damn flash drive would want to load Windows. I checked it on other laptops. everything works. But on this version of the BIOS. not a fig. I can’t install it on top either. Miracle Linux does not allow this to be done, referring to the fact that Linux does not recognize the.exe formats. What to do? How to be? Whom to complain to.

    The disk was made as usual with Rufus. It so happened that I had 10 windows for 4.5 GB, when I chose fat32, it reported that the file was too large (up to 4GB is possible) and was automatically put into NTFS. That was on a 128GB SD card. But it was not there, I decided to try it with a 64GB flash drive, and I managed to write to it in FAT32, eureka!

    Partition scheme chosen by MBR for computers with UEFI.

    Then, when loading, I pressed escape, entered the boot menu and chose to boot from the USB flash drive.

    That’s the end of this story, the author of the article is a great fellow! Success!

    Very, very, many thanks to the author. Almost a day was killed on this stupid muck that can only boot from FAT32.

    Asus X705MA-BX014 (without CD) the same “song” with a seven. with USB sidyuka-also a bolt. but the flash drive with a ten turned out to be in fat32. ALILUIA. no questions asked. and in the BIOS everything that the author has disabled (security boot and fast boot) is enabled. DRP 17.7.4 helped by half. on the office firewood only for wine10 / 64 I will download

    How to Boot Asus F550 Laptop From Bootable USB Drive to Install Windows 7/8/10

    So I did everything as the author said, but after you work esc, you select a USB flash drive, it gives it back to the BIOS

    And I, too, after esc selecting the flash drive back into the BIOS. What to do?

    And I, too, after esc selecting the flash drive back into the BIOS. What to do?

    He sees a flash drive, fast is disabled, securiti boot disable, a fat32 flash drive, does not want to boot. SATA has only one mode. AHSI, Legacy is not present

    Optional fat 32. My ntfs are easily loaded from a USB flash drive directly through the BIOS. After clicking on f7 in the saveexit section, you need to click on the name of the flash drive. You can also boot through system restore if the OS does not start. My laptop: Asus x541NC

    I suffered for a long time, perverted, it turned out I did not want to just accept the image of x86, I started installing x64 and the installation went from the very first time. I don’t know why he swore like that, but he threw it in the BIOS, spent 3 hours dancing, 4 flash drives, overwritten a hundred times in different ways, in the end, as I said above. The whims due to the bit depth were

    My laptop did not boot from x86 / x64 multi-image. With pure x64, the problem was solved.

    And I can see a USB flash drive in my BIOS, but it does not want to boot, please tell me

    Try to enter the BIOS after pressing f7 in the saveexit menu, look for the name of the flash drive there, it should be near winfowsboot (I don’t remember exactly what it’s called) click on the flash drive and you should start loading from the flash drive

    Please tell me how to add a new boot menu?

    Do not fuck your head, in Rufus 2.1, in the second paragraph from the top (partition diagram and type of system interface), select the parameter. GPT for computers with UEFI interface and you will be happy.

    PS: Pre-configure the BIOS as described by the author (just in case). GOOD LUCK. ))

    I mean that it is not necessary to write the file system as FAT32, you can leave NTFS.

    After resetting to default settings, I lost my SSD from boot devices, what could be the problem?

    Did as the author wrote 3 times it turned out to install Windu 10. In my case, the file system was installed correctly, the computer did not see the boot disk.

    The method works. And I was tormented with fkin NTFS.

    Tip: post a video to YouTube with this content

    Please help me with this task: on the Asus D541N laptop, Win 10 was originally installed, I wanted to reinstall it on Win7. I’m trying to install from a CD-ROM, at the beginning it seems to be an installation, but soon it gives an error: “An unexpected error occurred during the installation of Windows. To install Windows, restart the installer “, in general, in the BIOS settings, I accidentally deleted the CD-DVD, in Boot Priority. At the beginning, i.e. it was, and now only shows Windows Boot Manager. What should I do? how to return? please tell me

    On the fx505dy laptop, asus on the same BIOS rolled the system into FAT32, does not see it. Another PC sees. When I was rolling, there was a warning that FAT32 does not support files larger than 4 GB, I ignored it. I’m sitting, I don’t know what to do next, it was already the third distribution kit.

    Good day. ASUS X541U laptop. Installing Win 7 via a bootable USB flash drive. It seems that everything is loaded, and when she enters the menu to start the installation, it feels like the USB input is losing power.

    The installation starts and everything hangs on. starting Windows. What to do. I wanted to demolish the top ten and install 7.

    On the PC, everything goes and installs. Freezes on the laptop

    LAPTOP ASUS X507UA, BIOS does not load. Pressing F2 does not load BIOS, ASUS logo. that’s all. further nothing comes out. what to do?

    Thank you!! FAT32 helped solve the half-turn plug.

    I have an ASUS Tuf Gaming FX504 laptop, I connected an SSD from an old laptop to it via a USB port and wanted to boot into Windows from an external hard drive, but it didn’t work out for me, I already searched the entire Internet, but I could not find a way (((BIOS one in one as in the pictures from the author of the article, also there is no CSG in the boot.

    Please tell me who fumbles what to do

    It does not work because there is no fat 32 partition on the SSD. On the SSD, write Windows through rufus in Windows to go mode. Then go to the BIOS, then to the exit section and select your SSD there.

    ASUS m509 helped boot from external dvd. Windows10

    Hello, please tell me. how to make the new hard drive a priority? laptop ASUS X541N, that is, the same. but when installing a new hard drive or SSD. It is displayed in the BIOS, but it is not put in the priority boot in any way. Pre-translated the disk into gtp format. everything remained the same. I would be grateful for your help.

    Thank you. The point, however, is not in FAT32, although this too, but the choice of boot really helped. ASUS TUF Gaming A15 laptop. And, frankly, we got sick of these dances with the installation on new laptops

    Not necessarily fat32, you just need to create the correct flash: that is, strictly for ufi and not in any case under Legacy, that is, Legacy, this will work on all bios except what you have in your example. and if the BIOS is pure ufi, then the flash drive should be purely for ufi. that’s all

    Sorry, I was wrong, I need a fat 32, but the easiest way to do this is with the Rufus program

    It all started when I bought myself a second-hand ASUS Zenbook UX3400U ultrabook with Windows 10 64x already installed, since my old laptop is rather bulky, and it’s not very convenient to use it on business trips. I turned on the new device, checked everything like everything was ok, and the very first thought was to put my own, time-tested top ten. Nothing foreshadowed trouble, since I have been doing this for a long time and I was sure that it was a “minute matter”. I created a bootable flash drive, immediately downloaded all the drivers for a brand new laptop and started the installation process, but it didn’t work. The BIOS refused to see my flash drive for a cut, or rather the flash drive was displayed in the “USB Port” section, but it was not in the “Boot Priority” section. This situation did not bother me much, and I began to dig further. When I entered the BIOS, I was greeted by the graphic EZ Mode version 306 (I find out on the ASUS website that this version is extreme, and it’s quite problematic to roll it back), I check all the settings that may be the reason, but everything is fine here: Secure Boot Control was DISABLE. and CSM Support as it should be in ENABLE. Then, after digging around, I read on the sites “In order to boot from a USB flash drive in UEFI mode without problems and install Windows on a GPT disk. this flash drive must be formatted in the FAT32 file system”, after which I began to reload Windows onto a flash drive with different configurations (FAT32, NTFS, MRB, PRB), but all attempts were in vain and completely desperate (because I was not going to stay on the preinstalled Windows), I went for a set of screwdrivers just to simply transfer the SSD from the stubborn ASUS to my second laptop. and already there it is easy to install Windows. As expected, on the second PC everything went like clockwork, the flash drive was determined, the bootloader suggested that I install Windows and voila, my Windows is on an SSD and everything works fine. VICTORY! I thought, and returned the SSD with the installed Windows back, but when I tried to start the installed Windows, the inscription that broke my hopes came out: reboot and select proper boot device or insert boot media in selected boot device and press a key. Zenbook still did not want to give up and refused to see the Windows installed on the SSD (but there was one peculiarity, if a bootable flash drive was inserted, then there was no inscription, it was just an endless black screen). The next 2 days were a long wandering through the Internet, changing all the settings in the BIOS and even trying to roll it back, but “Moscow was not built right away” and I could not understand what was going on until I accidentally made one manipulation. Using rufus, I created a bootable flash drive with the following parameters: the partition scheme is mbr, and the file system is NTFS. The flash drive, by tradition, again did not appear in Boot Priority, and now changing the settings in Advanced Mode in the save exit menu in the boot override subsection, where our SSD is displayed (when you clicked on which a window with the inscription no found earlier came out), I selected it and hallelujah. somehow the Windows installation started from a flash drive, which was still not displayed anywhere. My joy knew no bounds, as a result, Windows stood up like a native, but I still did not understand “where the dog is buried”, suddenly someone will help, thank you for your attention.

    How do I set the BIOS to boot from a USB flash drive on an Asus laptop? A few tips for installing Windows 7 from a USB 3.0 stick

    Hello everyone! Yesterday I got my hands on a new laptop ASUS X501A. It was necessary to install Windows, and everything you need is shorter on a turnkey basis :). I twisted it and found that it does not have a CD / DVD drive. And this means that you need to create a bootable USB flash drive and install Windows 7 from it. Also, the drivers for it on the disk are included in the kit, you also need to rewrite them to the USB flash drive. In general, it is strange, a laptop without a drive, and a driver on a disk. You need to put the driver in the kit on the USB flash drive, or an external drive :).

    Anyway. I created a bootable USB flash drive. First, I created it using a special program Windows 7 USB / DVD Download Tool (I wrote about this here). but I will say, running to the front, that for some reason the installation of Windows 7 from this flash drive did not work. The white cursor just blinked and the installation did not proceed. I wrote down a bootable USB flash drive using UltraISO and it worked. Why so, I did not understand :).

    That’s it, the flash drive is ready. Now you need to install the boot from this flash drive in the BIOS. Now I’ll tell you how to do it.

    We expose the boot from a USB flash drive on an Asus laptop

    We go into the BIOS. For me, and most likely for you, this is the F2 key (if not, then try DEL too). Press it immediately after starting the laptop.

    The flash drive should already be connected to the laptop!

    Next, go to the Boot tab and select the Hard Drive BBS Priorities item.

    As you can see (in the screenshot below). I have a hard drive under Boot Option # 1. And under Boot Option is a flash drive. You need to install a flash drive under # 1.

    To do this, click on Boot Option and select the USB flash drive. And the hard drive will automatically take second place.

    You can return to the previous menu by pressing Esc and you will see that a USB device is installed under Boot Option # 1.

    Remember to press F10 and Yes to save the settings.

    Everything, after restarting the laptop, boot from the USB flash drive should go (if it is created correctly).

    There is one caveat. Perhaps I made a mistake when setting parameters in the BIOS, there probably you just had to create another rule for booting (Add New Boot Option). But it’s okay.

    If you did everything like me, then most likely, during the installation of Windows, after the reboot, the boot from the USB flash drive will start. And you need it from the C drive to continue the installation. I just pulled out the USB flash drive at the time of the reboot. And when the download started from the C drive, I inserted it back (although, it seems like it is no longer needed for installation, the files have already been copied, but I could be wrong).

    Possible problems installing Windows 7 from a USB 3.0 flash drive

    You may have noticed that my USB drive has a new USB 3.0 interface. And Windows 7 does not support USB 3.0, special drivers needed.

    If the drive itself is USB 3.0, then it’s okay. Just plug it into a USB 2.0 port on your laptop and everything will work.

    This is what the USB 2.0 connector looks like on a laptop:

    The third blue and two letters SS near the badge.

    Well, if you have all USB 3.0, then you will have to integrate the drivers into Windows 7. This is already a topic for another article. Perhaps I’ll write how to do it. In the meantime, you can find this information on the Internet.

    You can also find and download an assembly with Windows 7, which already has integrated drivers for USB 3.0. There are such.

    On this site there is probably all the information that can be useful for installing the operating system and for solving problems that may arise during the installation process. You can use the site search. And if you can’t find something, then ask in the Комментарии и мнения владельцев, I will tell you :). Good luck!

    Hello. In Windows 7 (and in earlier versions of Windows) there is such.

    Hi friends! All topics related to personal data, files and settings always.

    Hey! When I was writing an article on How to install Windows 7 with.

    Anyone who needs Windows 7 installation images, look for them on torrents, of which there are now a huge number of different ones. Yes, many are blocked, but still people somehow use them, use them and you are on your health!

    Man, God grant you health! The only one who could help me! Thank you!

    I did everything as written. Does not boot from a USB flash drive. How and what to create a rule, or rather, how is it clear what to write?

    Hello, in my BOOT tab, the inscription HARD DRIVE BBS PRIORITIES does not appear, ASUS X501A laptop model, what to do in this situation, if anyone has encountered such a problem, please help in advance thanks

    “In the BOOT tab the inscription HARD DRIVE BBS PRIORITIES does not appear”. Possible reasons:. The laptop is in UEFI mode. you need to switch to BIOS, see the passport for the laptop. Go to the Security settings and see what is on / off and compare in pictures in THIS forum thread, there is a detailed description. who has BIOS version 2.15.

    I wrote here above “In the BIOS, change the settings from UEFI, put others (I forgot what they are called).” so, change the boot from UEFI to BIOS.

    I bought ASUS R541s, I did everything correctly, the installation starts and then crashes what is not detected according to my words, the drive does not come out and tried to snag the system and install the drivers myself, but all the same, everything that is on the Internet does not work out that water does not help anything, it is not installed help pity

    I have a full fifth point. I have been friends with computers for a very long time) my uncle bought my sister a laptop asus x541sc…. I did all the manipulations from the flash drive, I booted them 2 (1 is just a regular Windows 7 from off site 2 the same Windows 7 but with USB 3.0 support) on both flash drives when I click on the button Start installation asks for a CD dvd USB, I put everything in a USB flash drive and all the same to rest with a horn! Both flash drives are made in UltraIso and both work great on the other 3 laptops! In general, 10 hours, I’m just no longer what to do, I just don’t know MB is there any advice? PS There is no cd roma in the laptop at all if you connect an external one at all from it does not want to load anything

    I myself am sitting with the same problem. But I figured out something. Drivers for USB from a flash drive cannot be read because they have not yet been installed and the system “does not see” the flash drive. Therefore, the USB drivers must be downloaded to the hard drive and installed from it when the Windows installation program requests them. I have a problem that I cannot find the necessary drivers for this Asus on Windows (on the intel site they are all packed).

    How good it used to be. I wrote Windows to the hard drive in another partition and, if necessary, then reinstalled it at any time.

    Hard disk partitioning style problem (GPT). Your review does not describe how to solve the problem.

    ASUS x540s laptop was purchased without OS. I’m trying to install 7k, wrote down a bootable USB flash drive, put everything in the BIOS correctly, sees the USB flash drive and starts downloading, but after unpacking, a blue screen of death comes out with an error 0x0000007E. I googled the error, there are many reasons, but I did not find it specifically for my malfunction. The problem is not in the flash drive, because it works on another laptop from this flash drive. Help please, what’s the problem

    Little information. If the installation image contains tools for working with HDD, make the disk standard, that is, in the MBR. I think that this error is due to the BIOS settings, perhaps there is a function for working in the HDD in UEFI mode. The 7 is not on friendly terms with UEFI. Try different BIOS settings.

    I’m trying to boot Windows 7, through the BIOS almost at the end of the installation a window-file crashes Tell me what is the problem with this asus ??

    Put 8.1 right away, this is the best. the best option it has all the drivers at once

    How to reinstall Windows on Asus laptop? Step-by-step instruction

    Good day, blog visitors.

    Any computer, regardless of the “stuffing” and the software used, sooner or later needs a clean installation of the operating system. This is due to various reasons. a new version has appeared, the old one is out of order, there is a desire to remove errors and others. Of course, reinstalling Windows on a laptop on Asus or any other manufacturer will help in all these issues. But today I’m just going to talk about the process associated specifically with the equipment from this computer giant.

    Create bootable portable memory

    It should be said right away that you can reinstall the OS in different ways. Previously, it was popular from disk, since there was simply no USB memory. In the early days, many motherboards did not support such devices. But over time, it became possible to carry out the necessary procedure from a flash drive. And already today this option often becomes the only one, since many models simply may not have a suitable drive.

    We’ll look at a no-disk option using only compact portable storage:

    We find the image of the required OS. Usually Windows 7 is downloaded from different torrent trackers.

    Install the UltraISO application. Since the program is paid, in order to use it, we press the “Trial period”. this will be enough for our purposes.

    Go to the “File” menu and then “Open”.

    Add the previously downloaded system image.

    We go to “Bootstrapping”, and then “Burn the image”. A new window will open where we select “USB-HDD”, and then “Format”. We confirm the action.

    At the end we are interested in “Record”.

    Preparation ( )

    If the installed operating system still allows you to work, there are three critical steps you must first take:

    Prepare the necessary drivers (for a video card, network). Having them, it will be possible in the future to find the rest of the elements.

    Check your computer for viruses with Comodo Internet Security or AVG AntiVirus Free

    Copy documents from system drive.

    If your device no longer allows you to complete the above points, try to find another one with which you can still do this.

    Important drivers for the Eee PC model or any others are on the official website.

    But copying documents from the system disk in case of laptop inoperability will not be so easy. If the device allows you to do this, we move it to a safe place. If not, open the laptop, take out the hard drive and try to connect it to other equipment. Pulling out the data you need.


    Well, now let’s move on to directly hosting Windows 8 or any other OS version on the device:

    After the system restarts, the display will show a message telling you to press any button to continue. Do it.

    A plate will appear where you need to specify your preferred language. As a result, we select “Install”.

    The “License Agreement” appears. We confirm reading.

    Then we need a “Full Installation”.

    Now we decide whether the process will take place with or without the removal of sections. Personally, I recommend allocating about 50 GB to the system disk. If you already have one, just click on the desired drive and then “Format”. We confirm our actions.

    BIOS setup

    Now we need to set the boot via BIOS and some other elements. To do this, we perform a number of actions:

    First you need to get to the above place. We reboot the device and immediately at startup press “Del”, “F2” or another key indicated on the monitor. it all depends on the model. For example, on k53s, the first option is suitable.

    Then we go to the “BOOT” tab and select Hard Drive BBS Priorities. We need to put the USB stick first.

    After we find “Launch CSM” and indicate “Enabled”.

    Open “Security” and remove “Boot Control”.

    At the end, press “F10” and confirm the action. This will save everything that we set, and then reboot the system.

    How to install Windows 10 on an Asus laptop with UEFI (using the ZenBook UX310UA model as an example)

    Good day.

    Not so long ago, I came across a compact laptop complaining about the impossibility of installing Windows 10 (the error “Installing Windows on this disk is impossible. Perhaps the hardware of this computer.”). Well, I had to figure it out.

    In fact, the problem was (I think) related to the fact that the user incorrectly created the bootable media and tried to install the system from it. Although, I will immediately note that in some cases, incorrect BIOS / UEFI settings may be to blame.

    In this article, I will show a step-by-step example of installing the OS on an ASUS ZenBook UX310UA laptop (I will add that on many ASUS laptops, especially from this line, the steps will be similar).

    Installing Windows 10 on an ASUS laptop

    Creating a bootable USB drive

    To work, you need the Rufus utility and a boot image with Windows 10 OS.

    A small but very versatile utility for creating bootable media. Allows you to create flash drives for BIOS and UEFI (for GPT and MBR disks), with different OS (Windows 10 is supported!). In addition, it is completely free and supports Russian.

    Windows 10 ISO image

    Requirements: you need an image that does not exceed 4 GB in size. Second, discard the different 20-in-1s at once. you need a simple option like “Windows 10 x64 home”. those. in the image one specific system (ie do not use any “Win 10 home / Pro / Ent x32 x64, 5 in 1”). There are a lot of such images on the net. (for example, can be downloaded from the official Microsoft website).

    And so, insert the USB flash drive and launch Rufus (Important! All data on the USB flash drive will be deleted, so copy everything you need from it).

    Next, specify the ISO image (recommended for installation above), then select the option “GPT for computers with UEFI interface” (file system. FAT 32). “Standard Windows Installation”. Click the “Start” button (the settings are shown in the screenshot below).

    Update from 01/24/2019 (since the Rufus program has been slightly updated, and its design has changed.I will give one more screen for version 3.4 so that no one gets confused).

    In general, the flash drive is ready, you can move on.

    How to create a bootable UEFI GPT flash drive with Windows 10, or why errors occur when installing the system on a new laptop (PC). a guide for beginners.

    Loading the optimal settings in the BIOS. enter the boot menu.

    BIOS settings are not always set by default (default). Therefore, first of all, I recommend to go into the BIOS and restore them.

    By the way, you can immediately connect the bootable USB flash drive created in the previous step. I recommend connecting to a USB 3.1 port (installation will be faster, especially if your flash drive supports this standard).

    We connect the flash drive to the USB 3.1 port (installation will be faster!)

    To enter BIOS. Immediately after turning on the laptop (the ASUS logo should appear) press the F2 key (preferably several times to be sure.).

    In BIOS (UEFI): first of all, go to Advanced Mode (F7 key). see the bottom of the window.

    In the “Save Exit” section, select the “Restore Defaults” option. Then save your changes. the “Save Changes” button (you can simply press the F10 button. after which all changes will be saved and the laptop will go to reboot. Enter the BIOS again with the F2 key).

    Restore Defaults. restore settings to default

    After restoring the settings, entering the main BIOS (UEFI) window again, press the F8 button (enter the Boot Menu). In it you should see our USB flash drive. select it and press Enter.

    Note: in the boot menu, you (most likely) should display 2 lines with the name of the installation flash drive. You need to select the one opposite which “UEFI OS” appears ().

    Boot Menu. select bootable media

    Next, the laptop must start installing Windows. a “circle” should run in the center of the screen.

    If the installation does not occur. check if you correctly recorded the installation USB drive and set the UEFI settings.

    Windows 10 setup process

    The first window is a greeting with a choice of language (I omitted it, just press Enter). In the next window. click the “Install” button.

    Next, a window with the license terms will appear. agree and click “next”.

    In the window with the choice of installation option, select “Custom: Windows installation only (for advanced users)”.

    In some cases, reinstalling the OS may be the reason for the refusal of warranty service (although, this is quite rare, but still. Most often, the warranty is given for hardware, and you can install any software.).

    deleting all partitions on the hard drive

    After that, you can create one partition on the entire disk and install it into it (some recommend creating two partitions, one for installing Windows, the other for user data). If create two sections. then under Windows I recommend allocating at least 100 GB of space.

    In my case, I just created one partition for the entire disk (931.5 GB) and clicked “Next”.

    How to Install Windows On ASUS laptop | Bootable Windows Step By Step Guide 2020

    Boot Menu. select bootable media, if at this step you see an error that “Windows cannot be installed on this disk.” (see screen below). then you most likely created the bootable USB flash drive incorrectly (see the first part of this article). It is also possible that you downloaded an “incorrect” ISO image with the system.

    Actually, if all is well. Windows installation should begin. Here you just need to wait while the files are copied (if you connected the flash drive to USB 3.1, then wait not long, 5-6 minutes).

    When the files are copied, the laptop will reboot and the installation will continue. Several windows will appear in front of you: but there is nothing interesting in them, you will need to enter a username, set network settings (you can also skip all the steps and do it after).

    I lowered all these windows, tk. they are of no practical interest, and I think that everyone will cope with them and independently.

    Actually, this completes the installation. Then you can start installing the drivers (in my case, it was enough to go to the official website on this page:

    But to be honest, just in case, I also resorted to Drive Booster and for extra. 5 minutes I updated not only the drivers, but also all sorts of libraries: DirectX, Visual C, Net FrameWork, etc. (without going anywhere and not looking for anything).

    A short video with the sequence of installing Windows on a device from ASUS.

    How to install Windows 10 on Asus X540 Laptop. Enable USB Boot in Bios Settings

    Creating a bootable USB flash drive with Windows 10

    To create bootable USB drives (and not only with Windows 10), I recommend downloading one small utility. Rufus.

    This program easily and quickly creates any bootable media (it works faster than many similar utilities). It is in it that I will show a little below how to create a bootable USB flash drive with Windows 10.

    By the way, whoever did not use the Rufus utility, you can use the utilities from this article:

    And so, step by step creation of a bootable USB flash drive (see Fig. 7):

    • run the Rufus utility;
    • insert an 8 GB flash drive (by the way, my downloaded image took up about 3 GB of space, it is quite possible that a 4 GB flash drive will suffice. But I haven’t checked it personally, I can’t say for sure). By the way, first copy all the files you need from the flash drive. it will be formatted in the process;
    • then select the desired USB flash drive in the device field;
    • in the partition scheme and system interface type field, select MBR for computers with BIOS or UEFI;
    • then you need to specify the downloaded ISO image file and press the start button (the program sets the rest of the settings automatically).

    Recording time is on average about 5-10 minutes.

    Configuring laptop BIOS to boot from a USB flash drive

    In order for the BIOS to boot from your bootable flash drive, you need to change the boot queue in the BOOT section settings. This can be done only by going into the BIOS.

    To enter the BIOS, different laptop manufacturers set different entry buttons. Usually, the BIOS entry button can be seen when turning on the laptop. By the way, just below I have provided a link to an article with a more detailed description of this topic.

    By the way, the settings in the BOOT section of laptops from different manufacturers are very similar to each other. In general, we need to put the line from the USB-HDD higher than the line from the HDD (hard disk). As a result, the laptop will first check the USB drive for boot records (and try to boot from it, if any), and only then boot from the hard drive.

    Below in the article are the settings of the BOOT section of three popular brands of laptops: Dell, Samsung, Acer.

    After entering the BIOS, you need to go to the BOOT section and move the “USB storage Device” line to the first place (see Fig. 8), so that it is higher than the Hard Drive (hard drive).

    Then you need to exit the BIOS with saving the settings (section Exit. Select the Save and Exit item). After restarting the laptop, the boot from the installation flash drive should start (if it is inserted into the USB port).

    Basically, the settings here are similar to a Dell laptop. The only thing is that the name of the line with the USB disk is slightly different (see Fig. 9).

    The settings are similar to those of Samsung and Dell laptop (slight difference in the names of USB and HDD drives). By the way, the buttons for moving the line are F5 and F6.

    Where to download Windows 10 (ISO image for installation)?

    This is the first question that arises before every user. To create a bootable USB flash drive (or disk) with Windows 10, you need an installation ISO image. You can download it both on various torrent trackers and from the official Microsoft website. Consider the second option.

    1) First follow the link above. On the page there are two links for downloading the installer: they differ in bitness (in more detail about bitness). In short: on a laptop 4 GB or more RAM. choose, like me, a 64-bit OS.

    2) After downloading and running the installer, you will see a window as in Fig. 2. You need to select the second item: “Create installation media for another computer” (this is the point for downloading the ISO image).

    3) In the next step, the installer will ask you to select:

    • – installation language (select Russian from the list);
    • – choose the Windows version (Home or Pro, for most users, Home will be more than enough);
    • – architecture: 32-bit or 64-bit system (about this a little higher in the article).

    4) In this step, the installer asks you to make a choice: will you immediately create a bootable USB flash drive, or just want to download the ISO image from Windows 10 to your hard drive. I recommend choosing the second option (ISO file). in this case you can always burn both a USB flash drive and a disc, and whatever your heart desires

    5) The length of the Windows 10 boot process depends mainly on the speed of your Internet connection. In any case, you can just minimize this window and continue doing other things on the PC

    6) The image has been downloaded. You can go to the next section of the article.

    How to install Windows 10 from a USB flash drive to a laptop


    Now the popularization of the recently released Windows 10 OS is starting in Runet. Some users praise the new OS, others believe that it is too early to switch to it, since there are no drivers for some devices, all the errors have not been fixed, etc.

    Be that as it may, there are quite a few questions on how to install Windows 10 on a laptop (PC). In this article, I decided to show the entire procedure for a “clean” installation of Windows 10 from scratch, step by step with screenshots of each step. The article is designed more for a novice user

    By the way, if your computer already has Windows 7 (or 8), it may be worth resorting to a simple Windows update: (especially since all settings and programs will be saved!).

    Step-by-step installation of Windows 10

    First, insert the USB flash drive into the USB port of the computer, and then turn on (restart) the computer. If the USB flash drive is written correctly, the BIOS is configured accordingly, then the computer should start booting from the USB flash drive (by the way, the boot logo is almost the same as in Windows 8).

    The first window that you will see when you start installing Windows 10 is the choice of the installation language (we choose, of course, Russian, see Fig. 12).

    Further, the installer offers us two options: either restore the OS, or install it. We choose the second (especially since there is nothing to restore yet).

    In the next step, Windows prompts us to enter a password. If you do not have it, then you can simply skip this step (activation can be done only later, after installation).

    The next step is to choose the Windows version: Pro or Home. For most users, the capabilities of the home version are enough, and I recommend choosing it (see Fig. 15).

    By the way, this window may not always be Depends on your ISO installation image.

    We agree with the license agreement and click further (see fig. 16).

    In this step, Windows 10 offers 2 options to choose from:

    Selecting a drive for installing Windows

    An important step during installation. Many users have incorrectly partitioned the disk, then edit and change partitions with the help of third-party programs.

    If the hard drive is small (less than 150 GB), I recommend that when installing Windows 10, simply create one partition and install Windows on it.

    If the hard drive, for example, is 500-1000 GB (the most popular volumes of laptop hard drives today), most often the hard drive is divided into two partitions: one per 100 GB (this is the system drive “C: \” for installing Windows and programs ), and on the second section they give all the remaining space. this is for files: music, films, documents, games, etc.

    In my case, I just selected a free partition (27.4 GB), formatted it, and then installed Windows 10 in it (see Figure 18).

    The next step is to install Windows (see Figure 19). The process can be quite lengthy (usually takes 30-90 minutes). The computer may be restarted several times.

    After Windows copies all the necessary files to the hard drive, installs components and updates, reboots. you will see a screen asking you to enter the product key (which can be found on the package with the Windows DVD, in an email, on the computer case, if there is a sticker ).

    You can skip this step, just like at the beginning of the installation (which I did).

    In the next step, Windows will offer you to increase the speed of work (set basic parameters). Personally, I recommend clicking the “Use standard settings” button (and everything else has already been configured directly in Windows itself).

    Next, Microsoft suggests creating an account. I recommend skipping this step (see Figure 22) and creating a local account.

    To create an account, you must enter a login (ALEX. see Fig. 23) and a password (see Fig. 23).

    Actually, this was the last step. the installation of Windows 10 on the laptop is complete. Now you can start customizing Windows for yourself, installing the necessary programs, movies, music and pictures

    A few words about drivers for Windows 10

    After installing Windows 10, drivers for most devices are found and installed automatically. But for some devices (today) drivers are either not found at all, or there are some, because of which the device cannot work with all the “chips”.

    For a number of user questions, I can say that most problems arise with video card drivers: Nvidia and Intel HD (AMD, by the way, recently released updates and there shouldn’t be any problems with Windows 10).

    By the way, about Intel HD, I can add the following: Intel HD 4400 is just installed on my Dell laptop (on which I installed Windows 10 while as a test OS). there was a problem with the video driver: the driver that was installed by default by the OS did not allow adjust the brightness of the monitor. But Dell quickly updated the drivers on the official website (2-3 days after the release of the final version of Windows 10). I think that very soon other manufacturers will follow their example.

    In addition to the above, I can recommend using utilities to automatically search for and update drivers: article about the best programs for auto-updating drivers.

    Several links to popular laptop manufacturers (you can also find all new Drivers for your device here):

    This concludes the article. I would be grateful for constructive additions to the article.

    How to install Windows 10 or Windows 7 on an asus vivobook

    Despite all the “attractions” of the asus vivobook, and there are quite a few of them, the owners have difficulties with installing Windows 10 / Windows 7, especially if they are trying to install from a flash drive.

    DVD drive is easier, but since it is not in asus vivobook 17, asus vivobook max, asus vivobook flip, asus vivobook 15, x540sa, d540n, x540ya, x712fa, a512f, x540na, x540ma dm298, 15 a512d, m712d, you have to buy a drive USB.

    Although it is not expensive, then who wants to toil with this now, if it is easier from a flash drive and it is now at hand for almost everyone.

    There is also a problem for those who install Windows 7, since drivers are usually provided only for the tenth version.

    Although not all the way here either. I recently bought a vivobook with a ten, and Wi-Fi worked extremely poorly.

    I wanted to download from the official resource, but alas, they weren’t there, I couldn’t even find my model, but let’s get back to the installation.

    How to install Windows 10 Windows 7 from a USB flash drive on an asus vivobook

    If nothing is done then your asus vivobook will not see the stick, so you must follow my steps to continue.

    In short, you need to create a UEFI flash drive with the Rufus program, then some may see the flash drive right away.

    If such an opportunity does not appear, then you need to go to the BIOS menu (as you ruled immediately after switching on, press “Esc”).

    Go to security secure boot disable save and exit. Then go to BIOS boot CSM menu to enable savd and exit. Step by step it is something like this.

    Insert the USB stick. Turn on the vivobook and immediately press ESC 5-10 times to open the boot menu. Then find the “Enter Setup” option, select it and press Enter.

    Once logged in, go to “Advanced” by pressing the right arrow key. There select “USB Configuration” and go to “XHCI Preboot Mode” and disable it.

    Now go to “Security” and disable “Secure Boot Control”.

    The next step is to enable “Launch CSM” on the download tab, but you will be denied the “Enable” option.

    To be able to enable Launch CSM, press “F10” and select “Yes” to save the configuration and exit.

    Now quickly press ESC 5-10 times and you will get into BIOS again. Now go to the Boot tab and you will see the Launch CSM option is available, just enable it and press the F10 button again to save.

    Then quickly press the ESC key 5-10 times to open the boot menu.

    Congratulations! Now you have the option of successfully unlocked boot and you can safely install Windows 10 or Windows 7 from a USB flash drive without straining your asus vivobook.

    just keep in mind that at the time of reading this entry, ASUS may make changes and this option will not work. Then write in the Комментарии и мнения владельцев. Success.

    BYRGPUB.COM 2022